Page 1
監錄易(監控錄影設備專門店) http://www.cam62.com User manual http://www.CAM62.com CA101 / CA111 / VI8908 / VI8908W IP Wireless / Wired Camera REMOTE PAN / TILT ROTATE User Manual CA101 CA111 VI8908 VI8908W 1 WELCOME This model IP Camera is an integrated wireless IP Camera solution. It combines a high quality digital Video Camera with network connectivity and a powerful web server to bring clear to your Desktop from anywhere on your local network or over the Internet.
監錄易(監控錄影設備專門店) http://www.cam62.com User manual Features Powerful high-speed video protocol processor High-sensitivity 1/4 CMOS sensor Picture Total 300k Pixels Video Frame Rate:30fps(QVGA), 30fps(VGA) Resolution:640 x 480(VGA), 320 x 240(QVGA) Light Frequency:50Hz, 60Hz or Outdoor Optimized MJPEG video compression for transmission Multi-level users management and passwords definition Embedded Web Server for users to visit by IE Support wireless network (WiFi/802.11/b/g)mobile...
監錄易(監控錄影設備專門店) http://www.cam62.com User manual 1.2 Packing List Untie the packing and checking the items contained against the following list; Wireless IP Camera Wi-Fi Antenna DC Power Supply Network Cable Mounting bracket NOTE: Contact us immediately in the case of any damaged or short of contents.
監錄易(監控錄影設備專門店) http://www.cam62.com User manual PC System Requirements System configuration requirements :( Example for view four IP Camera) CPU: 2.06GHZ or above Memory: 256M or above Network Card: 10M or above Display Card:64M or above memory Recommendable Operating system: Window2000 or Window XP or Vista Hardware Instruction Follow the steps below to set up your camera hardware.
Page 5
監錄易(監控錄影設備專門店) http://www.cam62.com User manual 1 SOFTWARE OPERATION SETTING IP Camera DevFind Tool Software Download Site : http://www.cam62.com/article.php?id=73 When the Device has been mounted properly, you can double click the Icon “IP Camera DevFind Tool” and a dialog box as will pop up.
Page 6
監錄易(監控錄影設備專門店) http://www.cam62.com User manual 3. The IP Cameras installed within LAN do not share the same subnet with the monitoring PC. A prompt as shown in result field (prompt: Subnet doesn’t match, double click to change!). Click the left mouse button to choose the prompt and click the right mouse, choose Network Configuration to set the IP address of the Camera to the same subnet as LAN.
監錄易(監控錄影設備專門店) http://www.cam62.com User manual Camera Login You can access the camera through IP Camera Tool or IE directly. Double click the IP address of the IP Camera listed. To access the camera ,start your web browser and type in the camera’s IP...
監錄易(監控錄影設備專門店) http://www.cam62.com User manual For Visitor The status of 9 routes, as shown below. For example: if is bright, the first route is on Detection (Motion Detection). If you want to detect 4 views, need to click this icon If you want to detect 9 views, need to click this icon OSD: Display date and time on the video .You can disable the OSD function or choice...
監錄易(監控錄影設備專門店) http://www.cam62.com User manual AUDIO: Click icon Camera MIC open, Local Voice input TALK: Click icon Camera Speaker open, Remote Voice Output RECORD: Click icon into REC mode, is stop. For operator When login as operator administrator, you can enter the IP Camera For Operator...
監錄易(監控錄影設備專門店) http://www.cam62.com User manual Resolution: VGA (640*480) / QVGA (320*240) Work mode: 50Hz/60Hz/Outdoor Color parameter: Click can adjust the brightness and contrast Image PTZ function: Image PTZ function is recommended, you can control the camera Direction on the video image. Double click the right mouse on the image to enable PTZ...
Page 11
監錄易(監控錄影設備專門店) http://www.cam62.com User manual Use multiple cameras with a single IP address In the Multi-Device Settings page .You can use multiple camera with a single IP address by configuring different ports for each camera .By default, the Device uses port 100 for accessing the camera’s homepage and video streaming.
Page 12
監錄易(監控錄影設備專門店) http://www.cam62.com User manual Upgrade Device Firmware Upgrade Device Firmware and device embedded web UI software in this page. Restore Factory Settings Restore factory settings of the device. Reboot Device Reboot the device.
監錄易(監控錄影設備專門店) http://www.cam62.com User manual 2.5.1 Network Settings Basic Network Settings If the router and the IP camera connect has DHCP function, you can choose “Obtain IP from DHCP Server” else fill in the network parameters manually. Http Port: In most cases, you can leave this value as however, if your Internet Service...
Page 14
監錄易(監控錄影設備專門店) http://www.cam62.com User manual Wireless Lan Settings Please enter the wireless net setting page of the wireless Router to out SSID, Channel, Encryption, Authentication. ADSL Settings When connected to the Internet through ADSL directly, you can enter the ADSL username...
監錄易(監控錄影設備專門店) http://www.cam62.com User manual UPNP Settings If you access IP Camera, to be make sure UPNP Status is Succeed. Protocol settings, as Figure below: UPNP 2.5.2 DDNS Service Settings DDNS Service: The system support protocols from some DDNS providers: Dyndns.org.
Page 16
監錄易(監控錄影設備專門店) http://www.cam62.com User manual 2.5.3 Other Service Settings Configure the E-mail box to receive and send mails. The E-mail box is used for receiving the images sent after alarm and the system IP address after successful dial-up. Mail Service Settings...
監錄易(監控錄影設備專門店) http://www.cam62.com User manual Alarm Service Settings Enter Alarm Service Settings page to configure Motion Detection function. Motion Detect Armed When you enable motion detect armed, the camera can be triggered to send email alerts sound you will hear. Motion Detect Sensibility...
監錄易(監控錄影設備專門店) http://www.cam62.com User manual Path Settings Setting the path of preserve video, when start record video, click , and the video file will be preserved in the specified directory Record Path. As below figure: 2.5.4 System Device Info You can find the information about Device ID, Firmware Version and Embedded Web UI...
Page 19
監錄易(監控錄影設備專門店) http://www.cam62.com User manual Alias Settings You can Input the new name as you like. Date &Time Settings Data &Time Settings page.
監錄易(監控錄影設備專門店) http://www.cam62.com User manual Users Settings Eight accounts are acceptable for this system. Here the eight users can Configure their user names and password as administrator, Operator or Visitor. Visitor: In this mode, you can only view. Operator: You can control the direction of IP Camera and set some parameter.
監錄易(監控錄影設備專門店) http://www.cam62.com User manual 4) Set the safety property of IE in the PC when you view it first time, 5) Camera login 6) Now you can use the IP Camera as Visitor, operator or Administration in the LAN. Setting Wi-Fi of IP Camera 1) To use the wireless function of the IP Camera, a wireless router like TPLink is required.
監錄易(監控錄影設備專門店) http://www.cam62.com User manual 4 APPENDIXES 4.1 Frequently Asked Questions Note: Any questions you would meet, please check Network connections firstly. Check the working status revealed by the indicators on the network server, hub, exchange and network card. If abnormal, check the network connections.
Page 23
監錄易(監控錄影設備專門店) http://www.cam62.com User manual —31— 4.1.5 Problems with network bandwidth The image frame rate is subjected to the following factors: 1, network bandwidth; 2, PC performance, network environment and display preference setting (brightness, theme, etc); 3, the number of visitors (Too many visitors will slow down the image frame rate.): 4, choice of switch or hub (Use a switch for multiple IP Camera Servers rather than a HUB,).