Subscribe to Our Youtube Channel
Summary of Contents for BRUEL & KJAER 4299
- Page 1 Technical Documentation Volume Velocity Adaptor Type 4299 Assembly Instructions English BE 1801 – 11...
- Page 3 Volume Velocity Adaptor Type 4299 Assembly Instructions February 2008 BE 1801−11...
- Page 4 Safety Considerations This apparatus has been designed and tested in accordance with IEC 61010 – 1 and EN 61010 – 1 Safety Requirements for Electrical Equipment for Measurement, Control and Laboratory Use. This manual contains information and warnings which must be fol- lowed to ensure safe operation and to retain the apparatus in safe condition.
-
Page 5: Table Of Contents
Contents CHAPTER 1 Assembly Instructions ..................1 Assembling the Microphones................2 Positioning the Microphones in the Adaptor ............3 Mounting the Adaptor on Sound Source Type 4295..........5 Mounting the Adaptor and Hose on Sound Source Type 4295 ......8... -
Page 7: Assembly Instructions
Chapter 1 Assembly Instructions... -
Page 8: Assembling The Microphones
Volume Velocity Adaptor Type 4299 – Assembly Instructions Assembling the Microphones Assemble the microphones, preamplifiers and colour-coded sleeves as shown in Fig.1.1. Fig.1.1 Attach the colour-coded sleeves before assembling the microphones and preamplifiers 2 × EU-4000 DB-4000 (blue) DB-4001 (red) -
Page 9: Positioning The Microphones In The Adaptor
CHAPTER 1 Assembly Instructions Positioning the Microphones in the Adaptor 1) Slide the cap on the adaptor to one side and insert the microphones as shown in Fig.1.2. Fig.1.2 Insert the microphones – red to red, blue to blue 080023 2) Ensure that the cones sit snugly in their receptacles (Fig.1.3). - Page 10 Volume Velocity Adaptor Type 4299 – Assembly Instructions Fig.1.4 Lock the caps 080033 4) Fasten the rubber belt around the adaptor to secure the preamplifier cables (Fig.1.5). Fig.1.5 Secure the cables (soft side of belt out) 080025...
-
Page 11: Mounting The Adaptor On Sound Source Type 4295
CHAPTER 1 Assembly Instructions Mounting the Adaptor on Sound Source Type 4295 Fig.1.6 Fixing the adaptor to the sound source 080026 Use the wires to fix the adaptor on the sound source (Fig.1.6). The procedure is as follows: 1) Place the metal lugs of the wires into the recesses of the adaptor (Fig.1.7). 2) Attach the metal band (Fig.1.8) to the body of the sound source and tighten the screw. - Page 12 Volume Velocity Adaptor Type 4299 – Assembly Instructions Fig.1.7 Fit the lugs into the recesses of the adaptor 080027 Fig.1.8 The metal band 080028 Fig.1.9 The screws and collars 080029...
- Page 13 CHAPTER 1 Assembly Instructions Fig.1.10 Attaching the wires to the metal band 080030 Fig.1.11 Tighten the wires 080031...
-
Page 14: Mounting The Adaptor And Hose On Sound Source Type 4295
Volume Velocity Adaptor Type 4299 – Assembly Instructions Mounting the Adaptor and Hose on Sound Source Type 4295 The method of attachment is the same as in section 1.3, but now the recesses for the wires’ metal lugs are at the end of the hose (Fig.1.12). - Page 16 HEADQUARTERS: DK-2850 Nærum · Denmark · Telephone: +45 4580 0500 · Fax: +45 4580 1405 · www.bksv.com · info@bksv.com Australia (+61) 2 9889-8888 · Austria (+43) 1 865 74 00 · Brazil (+55)11 5188-8161 · Canada (+1) 514 695-8225 China (+86) 10 680 29906 · Czech Republic (+420) 2 6702 1100 · Finland (+358) 9-755 950 · France (+33) 1 69 90 71 00 Germany (+49) 421 17 87 0 ·...
Need help?
Do you have a question about the 4299 and is the answer not in the manual?
Questions and answers