Table of Contents
Advertisement
Quick Links
spraymastertech.com
You have just purchased the best spray washer
on the market today. It incorporates the very
latest in technological advances. To assure
you the best and safest performance as well as
longest equipment life, please read the enclosed
information.
After reading the material in this manual, should
you have a service problem or need help, please
call our toll free number 1-800-548-3373 or
(479)636-5776.
TERMS: All parts will be shipped with check
in advance or C.O.D. Commercial accounts are
allowed 15 day terms from date on invoice with
approved credit.
FREIGHT: All freight will be paid by the customer.
Special consideration will be given to items under
warranty coverage.
IMPORTANT DOCUMENT - DO NOT DISCARD
Model Number
Serial Number
NOTE: Specifications found in this manual subject to change without notice.
FOR COMMERCIAL USE ONLY
SMT Wall Mount
SMT-600W, SMT-1100W
Owner's Manual
Date Purchased
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for SMT SMT-600W
- Page 1 SMT Wall Mount SMT-600W, SMT-1100W Owner’s Manual spraymastertech.com You have just purchased the best spray washer on the market today. It incorporates the very latest in technological advances. To assure you the best and safest performance as well as longest equipment life, please read the enclosed information.
-
Page 2: Table Of Contents
(479) 636-5776, or write to Spray Master Technologies®, 115 E. Linden St., Rogers, Arkansas 72756. SMT WARRANTY – LIMITED Effective May 16, 2014 Parts – Spray Master Technologies warrants parts for wall mounted and rack mounted 600 series and 2000 series units to be free from defects in material or workmanship for a period of 2 years from the date of shipment from the factory excluding items listed below. -
Page 3: Service Requirements
Manual. Also, refer to the CAT Pumps Service Manual provided with your system. If the problem is not Electric: resolved, then please call our toll free customer • SMT 600 & 1100 Series: service number: - 115 Volt/20 AMP Dedicated Circuit (NEMA 5-20R) or 1-800-548-3373 or (479) 636-5776. -
Page 4: Warnings
Warnings These "WARNING" labels are affixed to your system for all operators to read. If they have been removed or are unreadable, please call (800)548-3373 or (479) 636-5776 to order replacements. Note: Labels on this page are not to scale. Risk of Fire, Electric Shock or Personal Injury IMPORTANT SAFETY INSTRUCTIONS WARNING - When using this product, basic precautions should always be followed, including the following:... -
Page 5: Ground Fault Circuit Interruptor Protection
SMT unit away from risk of exposure to water. Water - The SMT unit is equipped with a 6-foot water supply hose. The unit or the hose bib should be positioned such that the supply hose can be easily connected with minimal stress on the hose. -
Page 6: Assembly And Installation
Water temperature - Water supply temperatures in excess of 120° F will cause the unit to shut down to protect the pump seals from damage. SMT recommends a water supply temperature of 120° F or less. Installation Procedure Refer to Figure 1 and Figure 2 for installation of the SMT600-W. - Page 7 Installation Procedure (continued) Refer to Figure 3 and Figure 4 for installation of the SMT-1100W. The SMT-1100W installation is similar to the installation of the SMT-600W. Differences in the installation are easily recognizable and should present little difficulty in adapting the instructions for the SMT-600W to the installation of the SMT-1100W.
- Page 8 Assembly and Installation Main Pump Installation (continued) Hose reel connection: If equipped with a hose reel, route the high-pressure pump hose behind the unit and connect to the fitting on the hose reel swivel. Use several wraps of Teflon tape on threaded fitting. GFCI power cord: Route the GFCI power cord out the back of the pump unit and connect it to the dedicated power receptacle.
-
Page 9: Operation
ON/OFF Switch: The Power ON/OFF switch is used to turn the pump motor on and off as necessary for operation. The ON/OFF switch is located on the upper right corner of the SMT-600-W cover. The SMT-1100-W ON/OFF switch is located just under the cover on the left side of the unit. -
Page 10: Accessories
Verify that the GFCI power cord/plug is fully inserted into the electrical receptacle and press the RESET button on the GFCI. • Verify there is adequate chemical and that the chemical pick-up tubes are fully submersed in the chemical. Cleaning With The SMT System • Hold the spray gun firmly. -
Page 11: Moving And Storage
Storage : Store SMT equipment and accessories so that they do not present a tripping or falling hazard. Protect from freezing. When storing SMT pressure cleaning units for extended periods or in freezing conditions, drain all water and winterize the system with antifreeze for use in potable water systems. -
Page 12: Chemical Metering Instructions
Step 3 The value at the point where the row (step 1) and the column (step 2) intersect is the ounces of chemical that should be injected into the SMT system during one minute to achieve the manufacturer’s recommended chemical solution strength.
Need help?
Do you have a question about the SMT-600W and is the answer not in the manual?
Questions and answers