Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Jadak PR-5
- Page 1 PR-5 2D Imager Module For Customer-Facing Designs Installation Guide...
-
Page 3: Required Accessories
GETTING STARTED What is the PR-5? The PR-5 0 is a 2D imager module designed to be integrated into fixed mount enclosures, such as a self-service kiosk. It is optimized to read 1D and 2D bar codes on mobile phone screens, coupons, loyalty cards or tickets at close reading distances. -
Page 4: Front View
Views Front View Mounting... -
Page 5: Back View
PR-5 2D Imager Module Installation Guide Back View USB-B Front Back PR-5 2D Imager Module Installation Guide PR-5 2D Imager Module Installation Guide... -
Page 6: Mechanical Dimensions
3. Verify that the PR-5 is on by presenting a bar code in front of the scan window. The white LED should turn on and read the bar code. Note: The PR-5 does not beep to indicate a good read unless this has been setup by the user with the user feedback pins (see User Feedback Pins on page 8). - Page 7 Distance Selection Switch The PR-5 is equipped with a movement detector that triggers the scanner when an object is detected. It is configured using the distance selection switch located on the PCB. The CF3680 can detect objects from contact (on the exit window) up to 30 cm (12 inches) ±15% (typical tolerance - for reference only).
-
Page 8: Configuration Bar Codes
Using the JADAK ImageView scanning tool Configuration Bar Codes Scan configuration bar codes to set up your scanner. All available configuration bar codes are available in the JADAK JE-238 User’s Manual. Contact your local JADAK representative for more information ImageView scanning tool... -
Page 9: Basic Setup
JADAK representative to get the latest USB driver. USB HID Keyboard Emulation Scan the following code to program the PR-5 for the USB HID Keyboard mode USB COM Port Emulation Scan the following code to program the PR-5 to emulate COM post... - Page 10 User Feedback Pins User feedback pins give access to certain pins on the scan engine so the customer can add additional functions. User Feedback Pins Name Description Vout Power Power supply voltage output, 5V ±5% nBeeper Output Open drain, 100K pull up on engine; idle high signal that can be active low DC or PWM controlled AC signal used to drive an external beeper.
-
Page 11: Installation Recommendations
Installation Recommendations • Do not cover the exit window with another window or replace it with a different window. • Do not block the movement detector or place anything in front of it. • Avoid direct light shining in to the scanner. - Page 12 TECHNICAL SPECIFICATIONS PR-5 Technical Specifications Physical Specifications Parameter Specification Dimensions (typical) W10.5 cm x H7.51 cm x D9.05 cm (W4.13 in x H2.95 in x D3.56 in) Weight 50g ±5g Interface USB-B connector Electrical Specifications Parameter Specification Input Voltage 5 VDC ±0.25 V Operating Power 4.75 to 5.25 VDC...
-
Page 13: Depth Of Field
Scanning Specifications Parameter Specification Scan Pattern Area Imager (640 x 480 pixel array) Movement Detector Configurable, 3 positions (0 to 30cm/12in) ±15% (typical tolerance - for reference only) Motion Tolerance 10 cm/s (4 in/s) at 2 cm (0.87 in) Print Contrast 35% minimum reflectance difference Illumination White LED illumination. -
Page 14: Typical Specifications
15 mil Data Matrix 3.4 in / 8.7 cm 20 mil QR 5.9 in / 15 cm Field of View/Resolution Decode Field of View Focus PR-5 Horizontal Field Angle (degrees) 37.8° ±1.0° Vertical Field Angle (degrees) ± 28.8° 1.0° Note: DPI can be calculated based on the following formula:... - Page 15 Bar Code Reading Angles Note: The following angles are not cumulative. Parameter Specification Specular Reflection ±5° Angle Pitch ±45° typical for 13 mil UPC ±45° typical for 20 mil Data Matrix Skew ±65° typical for 13 mil UPC ±45° typical for 20 mil Data Matrix Tilt 360°...
-
Page 16: Maintenance
Bleach – 10% • Gentle dish soap and a small amount of water (PR-5 is not waterproof) Note: For best scanner and movement detector performance, do not cover the existing exit window with another window or use a different exit window. - Page 17 • Cut resistant gloves • Pry tool (such as a spudger) made of plastic or with a plastic tip • Cotton tipped applicators • Isopropyl alcohol Replace the Exit Window To replace the exit window: Put on the protective eye wear and cut resistant gloves. Insert the edge of the pry tool under the edge of the glass window.
- Page 18 Inspect the interior and clean/remove any dust or debris. Open and remove the top plastic cover on the new window with red release paper facing upwards. Remove the red release paper. Do not touch the window with your fingers! Carefully apply the window (tape side down) onto the housing like the previous window.
Need help?
Do you have a question about the PR-5 and is the answer not in the manual?
Questions and answers