GDZX ZX3030B Manual

Ac/dc three phase standard power source

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

ZX3030B AC/DC Three

Phase Standard Power Source

Table of Contents

Need help?

Do you have a question about the ZX3030B and is the answer not in the manual?

Questions and answers

Summary of Contents for GDZX ZX3030B

Page 1 ZX3030B AC/DC Three Phase Standard Power Source...
Page 2 ZX3030B manual Attention This device is a high precision electronic equipment, it must be carried lightly during transportation and use. In order to ensure the precision of output and measurement, the equipment should be preheated for 30 minutes after turning on.
Page 3: Table Of Contents
ZX3030B manual Table of Contents I、 Introduction ......................1 II、 Functions and characteristics ................1 III、Specifications ......................1 IV、Familiar with the device ..................3 Front Panel Features ..................3 rear panel Features....................4 V、Operation instructions ...................5 Attention......................5 Main menu......................6 Ac output operation ................... 6 Electric energy error detection................8...
Page 4: I、 Introduction
[source meter integrated portable calibration device] developed by GDZX. The core technology of the device is ARM and FPGA, high speed and high precision D / A converters and direct digital synthesis technology (DDS). High precision parameter...
Page 5 ZX3030B manual Operating voltage and current regulation fineness: 5×10 － ▽ Voltage and current accuracy: The error is ≤ 0.03% (reading) + 0.02% (full);Grade 0.05 ▽ Voltage and current output power: The volume of each volume is 100% ▽ Output power is no less than 20W...
Page 6: Familiar With The Device
ZX3030B manual The error is ≤ 0.03% (reading) + 0.02% (full); Grade 0.05 ▽75mV、150mV, the output voltage accuracy (greater ≥ 200 ohm load): The error is ≤ 0.06% (reading) + 0.04% (full); Grade 0.1 current of 30uA, 5A, 20A) accuracy: ▽...
Page 7: Rear Panel Features
ZX3030B manual Rear Panel Features Figure 2 Pulse input and output terminals for watt-hour meter calibration. See figure 3 (Figure 3) Pulse Input: GND: grounding +5V: providing optoelectronic head power supply FL: low frequency pulse input Pulse Output: GND: grounding...
Page 8: Operation Instructions
ZX3030B manual (2). RS232 Interface RS232 communication interface terminal. (Figure 4) (3). AC Power Input Module (4) .Ground Terminal (5). Fan V. Operation instructions Attention Warm up electricity for at least 20 minutes before meter calibration. Turn it on at least 30 seconds after shutdown.
Page 9: Main Menu
ZX3030B manual Main menu The main menu screen shown in fig. 5 appears after the LCD is turned on. According to the main menu prompt, press the number key on the right side of the LCD display to enter the corresponding submenu.
Page 10 ZX3030B manual The middle part of the diagram shows the voltage, current, power, power factor and frequency values measured by the built-in standard. The lower half is used for shortcut key settings. Phase line setting: press the corresponding [< <] key, three-phase four-wire in the ...
Page 11: Electric Energy Error Detection
ZX3030B manual Electric energy error detection In the main menu, press the corresponding [< <] key on the right to enter the Power error Detection interface. Figure 7: Power operation window On the right side of the electric energy error detection interface is the power error output setting.
Page 12: Dc Output Operation
ZX3030B manual DC output operation Figure 8:DC operating window Voltage and current range setting: Press the corresponding [< <] key and highlight the  voltage range 10.0V, change the range by the up and down key, and press the [confirm] key to execute.
Page 13: Standard Configuration
ZX3030B manual VI. Standard configuration Hosts Test line RS232 communication line Pulse line power cable Aluminum alloy box manual Test Report Certification - 12 -...