Flo-Master 24101 Instructions

ASSEMBLE HOSE TO TANK
HOW TO FILL
HOW TO PRESSURIZE
HOW TO SPRAY
HOW TO RELEASE PRESSURE
SERVICE AND MAINTENANCE
Clean and dry your sprayer after every use to greatly prolong its useful service life. Many spray materials will harden if left in the sprayer and plug up the nozzle, shut-off valve or supply tube.
The soft parts, O-rings and gaskets, will ultimately wear out and need replacing, just like the oil fi lter on your car, for example. How often they need replacing depends on how much you
spray, the spray materials you use and whether or not the sprayer is regularly cleaned after use. Call 1-800-9-SPRAYER to obtain genuine Hudson® replacement parts. If you leave your
sprayer in the garage over winter, particularly in northern areas, the soft parts may dry out and need servicing before you use your sprayer for the fi rst time in the spring.
FOR YOUR SAFETY
This sprayer operates with liquid under pressure. Failure to observe cautions and follow instructions for use and maintenance can cause tank, hose or other parts to become corroded,
weakened, and/or burst. This can result in serious injury or property damage from forcible ejection of parts or high-pressure discharge of spray material. Do not use any fl ammables or
boiling liquids in this sprayer as it is not designed nor intended for such use. Not for use with acetone based products. Some spray materials can ignite or explode. Do not spray in
an enclosed space, near an open fl ame such as found in a bbq grill or water heater, near an electric motor or open switch, or any source of heat. Do not smoke while spraying. Use of
fl ammables could result in serious injury or property damage from unintended ignition or explosion. Do not use any caustics or acids in this sprayer, since these can damage or weaken
the sprayer and its parts, resulting in serious injury or property damage. Keep out of reach from children and pets. Always read and follow directions on the spray material container,
including the need for protective clothing. Before using your sprayer, thoroughly inspect both inside and outside of the sprayer and do not pressurize sprayer if tank, hose or other parts
appear to be damaged, discolored, brittle, excessively soft or loose. Do not pressurize with any mechanical device such as an air compressor, since this can create dangerous pressure
and bursting of parts and result in serious injury. Wear long-sleeved shirt, pants, gloves, goggles or similar protective clothing when spraying. PROP 65 WARNING: This product can
expose you to one or more chemicals, including lead, known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling. For
more information go to www.p65warnings.ca.gov.
LIMITED WARRANTY
H. D. Hudson Manufacturing Company warrants to the original consumer purchaser of this product at retail that it is free from problems in materials and workmanship for the period of 1
year from the original date of purchase. Visit hdhudson.com for specifi c model warranty period.This warranty does not apply to damage to the product resulting from accident, misuse,
neglect, alteration, modifi cation, tampering, or failure to follow instructions supplied with the product. This warranty does not cover normal wear and tear of o-rings or seals, and the
warranty shall be void if the product is used commercially. If the product or any part of it should malfunction within the warranty period, call 1-800-977-7293. Valid only in North America.
You must retain your sales receipt as proof of the date of purchase and include it with any return of
the product. H. D. Hudson Manufacturing Company excludes liablity under this warranty for any and all incidental and consequential loss or damages.
871-511 Instruction
Instructions for Polyethylene Sprayer 24101 & 24102
If you have any questions or concerns, or missing parts, do not return sprayer to the store.
Call or email Customer Service at 1-800-9-SPRAYER/ ladybug@hdhudson.com
1. Insert supply tube into the small tank opening and screw the tank nut down.
2. Make sure the tank nut is tight, if loose, it may come off with force or spray may escape,
resulting in injury.
1. Pour measured amount of spray material into the open tank. Follow label
directions on spray material container for amount to use.
2. Add water as directed. Do not fi ll beyond the max fi ll line.
3. Insert pump and turn clockwise to seal. Do not over tighten.
1. Unlock the pump hand by pushing down and turning counterclockwise.
2. Using the handle, pump up and down. (the more you pump, the more pressure
you will build inside the tank. When it becomes diffi cult to pump, your tank has
reached maximum pressure.)
3. Do not stand so your head is over the pump.
1. Squeeze the trigger on the handle to spray.
2. Push the trigger forward to lock on for continuous spray.
3. Then push the trigger back down to unlock.
Turn sprayer on its side and turn nozzle away from you. Squeeze shut off rigger to
let all the air escape. Turn sprayer upright and slowly unscrew pump from tank and
remove it.
1-800-9-SPRAYER
ladybug@hdhudson.com
©2019 Manufactured by H. D. Hudson
Manufacturing Company