djm direct VMA915-O Instructions Manual

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear
Instruction protective
manual gloves
1. SAFETY
1.1. Electrical Safety
WARNING! It is the user's responsibility to check the following:
R
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all
electrical connections for wear and damage. Ensure the risk of electric shock is minimised by the installation of appropriate safety
devices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We recommend that an
RCD (Residual Current Device) is used with all electrical products. It is particularly important to use an RCD with portable products
that are plugged into a supply not protected by an RCCB. If in doubt consult a qualified electrician. You may obtain an RCD by
contacting your local dealer. Electrical safety information, it is important that the following information is read and understood.
1.2. The Electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by a
qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.3. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.4. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and use a
Portable Appliance Tester.
1.5. Ensure that cables are always protected against short circuit and overload.
1.6. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.7. Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.

DO NOT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.

DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a

qualified electrician.
1.8. This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged, remove from use and ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13A 3 pin plug. If in doubt contact a qualified electrician.
A) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
B) Connect the BROWN live wire to the live terminal 'L'.
C) Connect the BLUE neutral wire to the neutral terminal 'N'.
D) After wiring, check that there are no bare wires and ensure that all wires have been correctly connected.
Ensure that the cable outer sheath extends beyond the cable restraint and that the restraint is tight. Double
insulated products are marked with the Class II symbol;
Class II products are wired with live (brown) and neutral (blue) only.
To rewire, connect the wires as indicated in diagram. DO NOT connect either wire to the earth terminal.
1.9. Products which require more than 13 amps are supplied without a plug. Contact a qualified electrician to ensure that a suitably
rated
1.10. Supply is available. Ensure that an industrial round pin plug and socket are fitted by a qualified electrician.
1.11. If an extension cable reel is used, ensure that it is fully unwound before connection. Use a reel that includes an RCD, an appliance
will be protected by the RCD. The cable core section is important and should be at least 1.5mm
is appropriate for this product. We recommend the use of 2.5mm² core section cable.
INSTRUCTIONS FOR
VALET MACHINE WET & DRY 30LTR
STAINLESS BIN
MODEL NO:
Wear
protective
clothing
Original Language Version
VMA915-O
Recommended fuse rating
13 Amp
. Ensure that the cable of the reel
2
VMA915-O Issue:1 - 19/05/15