Summary of Contents for FARMSCAN 5300C
- Page 1 5300C AND 5300H 5300 CONVENTIONAL Boom Interface 5300 HARDI Boom Interface Installation & Setup Guide...
- Page 2 A different trailer loom is provided for Hardi sprayers to match the reverse polarity on/off signaling. If you have purchased the 5300 NG option for use with the “Hardi Pilot”, an alternative connection scheme is to be followed. Will suit the Farmscan CF-18, CFM-33, CFM-34 and the RT-4000 guidance systems. AM-5300 farmscan.net...
-
Page 3: Installation
A-5300 NG2 SECTION INTERFACE AC-109 2M POWER EXT WITH PACKARD AC-5003-01 SECTION INTERFACE CABLE TRACTOR AC-5003-C-00 SECTION INTERFACE CABLE CONVENTIONAL AH-5300C FARMLAP 5300 CONVENTIONAL INSTALL AM-5300 5300 INSTALLATION & SETUP MANUAL Parts 5300H Part # Description A-5300 NG2 SECTION INTERFACE... - Page 4 5300 Installation and Setup Instructions AC-5003-01 AC-5003C-00 AC-5003H-00 AM-5300 farmscan.net 07/09/2006 +61 8 9470 1177...
-
Page 5: Typical System Layout
5300 Installation and Setup Instructions Typical System Layout This diagram applies for all Famscan contour guidance computers with the 5300 conventional & 5300 Hardi kits. Refer to the following pages for more information. AM-5300 farmscan.net 07/09/2006 +61 8 9470 1177... - Page 6 The existing connection from the GPS and guidance system has to be removed and connected to the 5300. Use the data cable supplied with the AH-5300C pack and connect the 5300 to the guidance system as shown in the diagram.
- Page 7 • Strip back both wires, (wire 1 Hardi, wire 1 loom). • Splice both wires together and crimp on a new terminal. • Carefully slide the terminal back into place. TIP: Remove and reconnect one wire at a time to avoid confusion! AM-5300 farmscan.net 07/09/2006 +61 8 9470 1177...
- Page 8 Left inside Off Section 3 Off 12 volts Right Inside Off Section 4 Off 12 volts Right Off Section 5 Off Master On 12 volts Master On Master Off 12 volts Master Off AM-5300 farmscan.net 07/09/2006 +61 8 9470 1177...
- Page 9 • Select the “MACHINERY” button. • Select the “MASTER CONTROL” button and scroll through the options to select the “BOOMBITS_NG_5300” option. Select this option • Continue to select the “CONTROL” button to setup your sections and widths. AM-5300 farmscan.net 07/09/2006 +61 8 9470 1177...
- Page 10 The 5300 can be configured to work with 1 to 5 section boomsprays. • Select the “WIDTH” button to adjust your individual boom section widths. Each section can be adjusted one at a time by pressing the “SECTIONS” button at the bottom of the screen. AM-5300 farmscan.net 07/09/2006 +61 8 9470 1177...
-
Page 11: Testing The Installation
Green section indicators indicates that your sections are ON, Red indicates OFF. Try to turn each individual section on and off to verify this. NOTE: You must have a GPS signal for this to work Section status Indicators AM-5300 farmscan.net 07/09/2006 +61 8 9470 1177... - Page 12 Click “View” -> “Options” from the menu bar. With the options window open click “Expand” -> “Section Control”. The following screen will appear. Select this option After selecting the Boombits NG Option, select Master under Options. Select depending on installation AM-5300 farmscan.net 07/09/2006 +61 8 9470 1177...
- Page 13 Follow the procedure below to test installation. 1. Open the NG Test software by clicking: Start -> Programs -> Farmscan -> NG Test. The window below will appear.
-
Page 14: Troubleshooting
Loom and sprayer loom. Section not responding on Break in circuit Check all connections for break, Farmlap when switched on between 5300 and corrosion etc. Clean and spray controller. sprayer loom. reconnect where necessary AM-5300 farmscan.net 07/09/2006 +61 8 9470 1177...