Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Zubler 330 Series
- Page 1 EN07-2022 EN07-2022...
-
Page 3: Table Of Contents
CONTENTS from page 0. Introduction 0.1 Declaration of conformity 0.2 General 0.3 Intended use 0.4 Safety instructions Installation 6 Setting up the device Initial installation Display Diagnostic program 2. Operation 2.1 Program selection 2.1.1 Preview 2.1.2 Start program 2.1.3 Change program during a program run 2.1.4 Program abort 2.1.5... -
Page 4: Introduction
Performance and economy are nability. Perforamnce and economy are in favor of a Zubler furnace VARIO 230 favor of the Vario Press 330 pressing fur- with experienced dental technicians. The of experienced dental technicians. Our basic requirements. -
Page 5: Safety Instructions
0.4 Safety instructions Position the oven in the up-right Do not use an extension cord with Do not attempt to open, repair, position. A clearance of 200-300 the oven. Ask your electricity supplier or replace any part of your oven mm must be maintained above and about the electrical connection until you have read the manual... -
Page 6: Installation
1. Installation 1.1 Setting up the device 1.2 Initial installation After switching on for the first time, Place the oven on a stable and level instructions for the first steps are work station shown on the display. After that, the Set up the vacuum pump near the initial installation cycle runs auto- oven (remove the rubber cover from... -
Page 7: Display
Oven type / folder Main menu Furnace actual temperature Number pad VP330eZR Main menu 500°C Select program Edit program Fenster Durchsicht Display Warm-up oven Standby Settings 1.3 Display 1.4 Diagnostic program The display of the VARIO furnaces is a When you switch on the device, the oven full-touch display including an additional starts a diagnostic program to check the number block... -
Page 8: Operation
2. Operation Selection of the menu parameters Main menu 500°C VP330eZR VP330eZR After the furnace is switched on, the main menu with five options appears on the display. Selecting an option takes you directly to it. Programmwahl Select Program Programm bearbeiten Edit program Ofen vorwärmen Warm-up oven Stand-by Standby Einstellungen... - Page 9 Select program 500°C DC 9.2 DC 9.2 DC 9.2 Full Zirkon Wash Stain 3+ Stain DC 9.2 DC 9.2 Full Zirkon Dentin 1 Correction Glaze DC 9.2 Dentin 2 DC 9.2 Stain DC 9.2 Glaze Folders Preview Start Display, Status: Select program / select a folder / program selected Image 09.1 2.1.1 Preview - change program Preview...
-
Page 10: Start Program
2.1.2 Start program Preview 500°C As soon as a program is started DC 9.2 Professional using the green Start button, the Correction program sequence is displayed once Start temp. Heat rate Opening temp. as a graph and as a list of 450 °C 35 °C/min 720 °C... -
Page 11: Change Program During A Program Run
2.1.3 Change program during a Edit program 500°C program run DC 9.2 Parameters can be changed during Professional Correction a program run via the program Start temp. Heat rate Opening temp. Edit program button. As with the 450 °C 35 °C/min 720 °C program preview (image 10.2), these Pre dry... -
Page 12: Functional Error During Program Execution
2.1.5 Functional error during Dentin 1 500°C DC 9.2 program execution In the event of a functional error, the Error oven interrupts the work process and displays a window with an error message in plain text and an error code. V-01 This error message and the program Abort: Vacuum error... -
Page 13: Program Overview And Parameter Assignment
2.1.7 Program overview and parameter assignment Ceramic firing program type with optional tempering function Professional Ceramic firing program type with optional, linear, cooling rates - controlled temperature feedback Professional TTC 2 - phase firing program (two heating stages including holding time) 2-Step 2-phase firing program with optional, linear, cooling rates - controlled temperature feedback 2-Step TTC Types of burning program Professional Parameter Professional 2-Step 2-Step TTC Start temperature Pre dry Pre dry time Closing time Soak temperature Soak time Heat rate Final temperature Hold time Heat rate 1 and 2... - Page 14 2.1.8 Explanation of terms Start temperature The temperature in the firing chamber at which the program begins. Pre dry Selecting "YES" activates the pre-drying program. Pre dry time Enter a time value. In this section, the lift looks for a predetermined position over the entire period, depending on the radiated heat of the heating chamber, in which the object is thus pre-dried at a constant temperature.
-
Page 15: Edit Folder / Programs
2.2 Edit folder/program In the Edit program area, folders Edit Folder 500°C or programs can be created, edited, copied or deleted. A basic distinction DC CONCEPT PRESS DC 12.5 Ceramay Hans is made between two "levels". The "folder level" and the "program level". DC 12.5 DC 9.2 Ceramay... - Page 16 Edit program 500°C DC 9.2 Sarah The New function field is activated as soon as an empty program or folder DC 9.2 DC 9.2 Full Zirkon function field has been selected. If WASH Stain 3+ Stain the New field is now pressed, the DC 9.2 DC 9.2 Full Zirkon...
- Page 17 Delete Delete 500°C After pressing the Delete function field, a security query appears, which you must confirm with Yes or No. Delete The program will be permanently deleted! DC 9.2 Sarah Dentin 1 Display, Status: Edit program / folder selected / Programs / existing program selected / Delete Image 17.1 Edit Edit program...
- Page 18 Name programs / folders Edit program 500°C If a new program or a new folder is to be created, a name must first be DC 9.2 entered. Two lines of text, each with a maxi- Dentin 1 mum of 12 characters or letters, are available for this purpose (image 18.1).
-
Page 19: Warm Up
2.3 Warm-up If you select Warm-up, the device Main menu 500°C V230ZR starts a program to heat up to the operating temperature. The furnace is preheated to 900°C and held for 10 minutes. The heating Select program chamber is then heated through homogeneously. -
Page 20: Settings
Main menu Display, Status: Settings Image 20.1 2.5.1 Data transfer Data transfer 500°C Included with your Zubler ceramic furnace a USB data stick (flash drive) is enclosed. Import all folders With the help of this USB stick you can transfer program datas (from the oven to Export all folders USB or from USB to oven) or log datas for quality assurance to save. - Page 21 Export all folders Export all folders 500°C When the Export all folders function field is activated, all folders on the furnace are saved from the Export furnace to the USB memory and can be transferred to another furnace. The furnace creates the file name as Do not turn off the oven! model name of the furnace, serial number of the furnace, date and time...
- Page 22 Export protocol files Protocol files 500°C For documentation and quality assurance, the last 50 program runs and results can be downloaded with a csv file. Accomplished programs After 50 program sequences have Last data backup been saved, the furnace overwrites 01.02.22 the previous log data, starting with the oldest, in subsequent work pro- cesses.
- Page 23 2.5.2 Firmware update / Firmware Firmwareupdate / Firmwareversion 500°C version Firmware Display Board Firmware Presseinheit I/O Board number of series Firmware version and Firmware 00-00-24 123456789-1234-1 update. Firmware Date Firmware Press Kernel The firmware versions of the relative 2022-03-18 15:10 components are displayed here. Firmware I/O Board Hardware Version Press A firmware update can be installed on 00-00-27...
-
Page 24: Idle / Standby Temperature
2.5.3 Idle- / Standby temperature Idle / Standby temperature 80°C Both the Idle and the Standby tempe- DC 9.2 rature can be set up in this area. The Stain 3+ idle temperature is the temperature that the oven idles at between programs. This Idle temperature is to maintain the oven at operating tem- perature. -
Page 25: Last Error Message
2.5.5 Last error message Last error message 500°C The last error message displayed by the oven can be called up again here. This is DC 9.2 Dentin - 10.05.2022 - 14:12 retained until the oven displays an error message again and is then updated in the process (image 25.1). -
Page 26: Basic Settings
2.5.9 Basic settings Basic settings 500°C In this area, specific display settings can be made. Select language These are: Set date and time Set unit system Set brightness Set volume Settings Display, Status: Settings / Basic settings Image 26.1 Select language Select language 500°C Selection of the menu language. To do this, select the desired national language by activating the red Back button you´ll get back to the Basic... - Page 27 Set brightness Set brightness 500°C Setting the display brightness using the slider. 4 test color patches are Test used for orientation. Activate the slider until the display shows the Test desired values. With the red Back function field you´ll return to the Basic Test settings level (image 27.1). Test Back Display, Status: Settings / Basic settings / Set brightness...
-
Page 28: Vacuum, Pressure, Lift
2.5.11 Vacuum, pressure, lift Vacuum, pressure, lift 500°C This area is divided into further sub- areas. These are: Vacuum test Vacuum pump mode Pressunit test Lift test Vacuum test The oven starts the vacuum test by pressing the green function field Back Start. -
Page 29: Service Menu
To do this, you request a basic code deleted. under this menu item, which you send to your dealer or to us at Zubler Gerätebau GmbH. You will then receive an activa- tion code which you can enter in this menu area. You confirm this code with... -
Page 30: Data
3. Data 3.1 Technical Data Image 30.1 Width 320mm Height 765mm Depth 445mm Weight 30kg Voltage 115V AC / 230V AC ±5%, 50-60Hz Power consumption 1600VA Idle temperature 20°C - 700°C Temperature 20°C - 1200°C Colour display 152 x 92mm Touch 230 x 92mm Programs... -
Page 31: Scope Of Delivery
3.2 Scope of delivery 1x Power Cord 1x USB flash drive 1x Muffle tongs 1x Firing tray 1x Press tray including press insert (centering disc) 1x Compressed air hose 1x Pressure reducer (water separator) with mounting bracket 1x Long tweezer 1x Fine filter 1x Vacuum hose 1x Connection cable "furnace - vacuumpump" 1x User manual 1x Honeycomb tray inclusive 5 pins 1x Flexring system 100gr. with muffle base 13mm... -
Page 32: Status Messages
4. Status messages Error indication Error indication Cause Cause Remedy Remedy H-01 H-01 Abort: Heating system error Abort: Heating system error the oven does not heat up. the oven does not heat up. - please contact your for oven service dealer or - please contact your for oven service dealer or service company. -
Page 33: Warranty
5. Warranty 5.1 Filter element for vacuum pump P3 The filter element prevents components of the insulation material of the heating chamber dissolved in the condensate or extremely fine dust from entering the vacuum pump. We recommend replacing this filter element after 3 years at the latest. 5.2 Cleaning the heating chamber see point 2.5.7 5.3 Checking the water separator Please check the container for water separation after the press furnace has been put into operation at short intervals, about every 4 weeks. Accumulated water must be drained by loosening the screw plug. -
Page 34: Guarantee
Zubler guarantees professional repairs with original spare parts. A guarantee period of 6 months is granted for every repair carried out by a specialist dealer or by Zubler, provided that all maintenance work required for the unrestricted function of the device has been commissioned. - Page 36 Zubler Gerätebau GmbH Buchbrunnenweg 26 89081 Ulm-Jungingen Germany...
Need help?
Do you have a question about the 330 Series and is the answer not in the manual?
Questions and answers