Related Manuals for Bernhard EXPRESS RELIEF
Summary of Contents for Bernhard EXPRESS RELIEF
- Page 1 EXPRESS RELIEF EXPRESS RELIEF for Express Dual Spin Grinders with Lift Table User s Guide & ’ Instruction Manual Please read this manual carefully. This manual should be kept in a safe place so that it can be used for future reference.
- Page 2 Welcome to the Bernhard Express Relief. If cared for and operated correctly this machine will give you years of good service. This manual will enable you to obtain the best results from your Express Relief so please read it thoroughly before using your machine.
- Page 3 EXPRESS RELIEF USER INSTRUCTIONS EXPRESS RELIEF in Up position EXPRESS RELIEF in Down position © Bernhard and Company Limited...
- Page 4 NEVER fit or use a grinding wheel (or other spares) other than those supplied specifically for use on the EXPRESS RELIEF (Warranty will be invalidated). NEVER fit or use a grinding wheel which has been dropped or subjected to any other form of abuse.
-
Page 5: Installation
Undo the two wing knobs and remove the cover from the lft table mechanism. Using an ‘allen’ key in the adjusters, adjust the chain length so that the platform and the machine table are level. © Bernhard and Company Limited... - Page 6 Place the Express Relief on the lift table platform as shown (ensure that the bolts securing the support/pivot shaft to the bracket go into the detents in the shaft). Position the support bracket so that it is central on the side plate of the lift table chassis.
- Page 7 EXPRESS RELIEF User Instructions These instructions assume that the Express Relief has been correctly fitted to the lift table of an Express Dual according to the supplied fitting instructions. If the Express Relief is in its "lowered" position, supported on the lift table platform, lower the lift table platform to the ground.
- Page 8 Express Relief to the horizontal position. Raise the platform to it’s highest position once more to support the Express Relief frame. Bring the cutting unit onto the Express Relief so that it’s rear roller is located in the ‘V’...
- Page 9 [D], Loosen locking lever [E] to enable angular adjustment of the grinding head. 3.10 Fine adjustment of mower position back and forth can be achieved by moving the vee support for the rear roller with the handwheel. © Bernhard and Company Limited...
- Page 10 Note: Ideally mark the first blade that is ground, grind each blade in turn for one complete revolution of the reel, then apply a fine finishing cut and repeat grinding for one revolution of the reel in the opposite direction. © Bernhard and Company Limited...
-
Page 11: Parts List
EXPRESS RELIEF 4. Parts List Page EXPRESS RELIEF COMPLETE ____________________________ 11 EXPRESS RELIEF FRAME ASSEMBLY _____________________ 12 FRONT RAIL ASSEMBLY _________________________________ 13 GRINDER TROLLEY ASSEMBLY __________________________ 14 HINGE ASSEMBLY ______________________________________ 15 RIGHT HAND MOWER SUPPORT ASSEMBLY _______________ 16 LEFT HAND MOWER SUPPORT ASSEMBLY ________________ 17... - Page 12 EXPRESS RELIEF 4. Parts List (Continued) Ref # Name of Part Qty. Part # EXPRESS RELIEF FRAME ASSEMBLY _________________________ Main Frame Fabrication ............1 03934 Feed Screw Bush ..............1 03718 Single Slide Rail ..............2 03422 BT Roller Cradle ..............1 04154 Roller Cradle Feed Assembly ..........
- Page 13 Kip Lever M10x30 ..............2 06119 Hexagon Nut ISO - 4032 - M12 - D - N ........2 ISO 7380 - M5 x 12 --- 12N ........... 11 ISO 7380 - M10 x 30 --- 30N ........... 2 © Bernhard and Company Limited...
- Page 14 ISO 4018 - M8 x 16-WN ............2 ISO 10642 - M6 x 16 - -- 16N ..........8 BS 4168-5 - M6 x 8-N ............. 2 ISO 7380 - M6 x 12 --- 12N ............. 4 © Bernhard and Company Limited...
- Page 15 Hinge Support Fabrication ............1 03378 Hinge Fabrication ..............1 03377 T Pin ..................1 04262 1 1/4” Set Collar ............... 2 04050-14 BS 4168-5 - M10 x 10-N ............2 ISO 4018 - M8 x 30-WN ............2 © Bernhard and Company Limited...
- Page 16 LH Vice Grip Clamp Fabrication ..........1 03727 Support Stay Spacer ............... 1 03366 M8 x 15mm Lobe Knob ............3 06131 Wing Knob M6x10 ..............1 06126 Black washer BS 4320 - M8 (Form G) ........3 © Bernhard and Company Limited...
- Page 17 RH Vice Grip Clamp Fabrication ..........1 03726 Support Stay Spacer ............... 1 03366 M8 x 15mm Lobe Knob ............3 06131 Wing Knob M6x10 ..............1 06126 Black washer BS 4320 - M8 (Form G) ........3 © Bernhard and Company Limited...
- Page 18 Rest of World: UK Head Office, England (+44) 1788 811600 Email: techsupport@bernhard.co.uk Technical FAQs can be found on our web site: www.bernhard.co.uk When ordering spare parts please quote the machine type and serial number. THE MANUFACTURERS ACCEPT NO RESPONSIBILITY FOR ANY SITUATION ARISING FROM THE FITTING AND/OR USE OF NON-ORIGINAL SPARE PARTS.
Need help?
Do you have a question about the EXPRESS RELIEF and is the answer not in the manual?
Questions and answers