Mac allister MBCP33-4 Manual

Petrol brush cutter (33 cm3)

Hide thumbs

Table Of Contents

Petrol Brush

Cutter (33 cm

)

MBCP33-4

EAN: 5059340124322

BX220IM

WARNING: Read the instructions before using the machine.

Table of Contents

Summary of Contents for Mac allister MBCP33-4

Page 1 Petrol Brush Cutter (33 cm MBCP33-4 EAN: 5059340124322 BX220IM WARNING: Read the instructions before using the machine.
Page 2: Table Of Contents
MBCP33-4 Let’s get started... These instructions are for your safety. Please read through them thoroughly before use and retain them for future reference. Getting Started... Safety information Technical Your machine Before start Quick start more detail... Machine functions Operation Care...
Page 3: Safety Information
Safety information MBCP33-4 Safety warnings IMPORTANT READ CAREFULLY BEFORE USE KEEP FOR FUTURE REFERENCE 1. This machine is not intended for use by children and persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge. 2. Children should be supervised to ensure that they do not play with the machine.
Page 4 Safety information MBCP33-4 10. Keep bystanders and animals at least 15 metres out of the work area. 11. Do not operate the machine if it has faulty safety equipment or damaged parts. 12. Do not under any circumstances modify the machine. Modifications can result in serious personal injury or death.
Page 5 Safety information MBCP33-4 4. Keep handles dry, clean and free from oil and grease. Greasy, oily handles are slippery and may cause loss of control. 5. Do not operate the machine if you are tired or ill, under the influence of drugs, alcohol or medication.
Page 6 Safety information MBCP33-4 Fuel handling 1. Always switch the machine off, disconnect the spark plug connector and let the machine cool down before refuelling it. 2. Fuel and fuel vapour are highly flammable. Take care when handling fuel. 3. Do not smoke while operating the machine, handling fuel or near fuel.
Page 7 Safety information MBCP33-4 3. Allow the engine to cool before storing in any enclosure. 4. Never store the machine with petrol in the tank inside a building where fumes can reach an open flame or spark. 5. Store the machine and fuel so that there is no risk of leakages or fumes coming into contact with sparks or naked flames from electrical equipment, electric motors, relays/switches, boilers etc.
Page 8 Safety information MBCP33-4 Residual risks Even if you are operating this machine in accordance with all the safety requirements, potential risks of injury and damage remain. The following dangers can arise in connection with the structure and design of this machine: 1.
Page 9 Safety information MBCP33-4 Description of signal words: The signal word that indicates a hazard with a high level of risk DANGER! which, if not avoided, will result in death or serious injury. The signal word that indicates a hazard with a medium level of WARNING! risk which, if not avoided, could result in death or serious injury.
Page 10 Safety information MBCP33-4 Petrol engines produce toxic carbon monoxide exhaust fumes. Breathing 40:1 carbon monoxide can cause nausea, fainting or even death. Do not operate the engine indoors! Stop the engine before refuelling. Never refuel the machine while the engine is running.
Page 11: Technical
Safety information / Technical specifications MBCP33-4 Designation of the tool MBCP33-4 (M_Brand Name; BCP_Brush Cutter Petrol; 33_Engine size in cc) The machine complies with the applicable European directives and an evaluation method of conformity for these directives was done. Technical specifications General >...
Page 12 Technical specifications MBCP33-4 Sound emission level Equivalent sound pressure level at operator position determined in accordance with ISO 22868 Brush cutter L > 98.2 dB(A) pA av > Grass trimmer L 93.2 dB(A) pA av > uncertainty: 3.0 dB(A) Sound power level determined in accordance with ISO 22868 and Directive 2000/14/EC >...
Page 13: Your Machine
Your machine MBCP33-4 Tri-arc blade String trimmer head...
Page 14: Before You Start
Your machine / Before you start MBCP33-4 1. Power unit 18. Tube clamp 2. Spark plug connector 19. Lock pin 3. Ventilation openings 20. Wing knob 4. Recoil starter handle 21. Bottom drive shaft tube 5. Fuel tank cap 22. Gear head 6.
Page 15 Before you start MBCP33-4 WARNING! The machine and the packaging are not children’s toys! Children must not play with plastic bags, sheets and small parts! There is a danger of choking and suffocation! You will need (items not supplied) (items supplied) >...
Page 16 Before you start MBCP33-4 Assembling the U-handle 1. Attach the U-handle (10) onto the handle connector (11) making sure to align the pin on the U-handle with the hole on the connector (Fig. 1). 2. Press and turn the fixing...
Page 17 Before you start MBCP33-4 2. Loosen the three pre-assembled screws on the gear head (22), using the multi-tool II (35) (Fig. 3). 3. With one hand holding the backing flange (27) and the locking flange (28), turn the securing nut (29) clockwise to loosen it.
Page 18 Before you start MBCP33-4 6. Put the backing flange (27) onto the spindle (26) (Fig. 5). 7. Rotate the backing flange (27) until one of its grooves is aligned with one of those on the gear head (22). 8. Insert the multi-tool II (35) into the groove to lock the rotation of the spindle (26).
Page 19 Before you start MBCP33-4 5. Put the backing flange (27) onto the spindle (26) (Fig. 8). 6. Rotate the backing flange (27) until one of its grooves is aligned with one of those on the gear head (22). 7. Insert the multi-tool II (35) into the groove to lock the rotation of the spindle (26).
Page 20 Before you start MBCP33-4 Assembling the bottom drive shaft tube 1. Pull out the lock pin (19) on the tube clamp (18). Insert the bottom drive shaft tube (21) into the upper drive shaft tube (17) (Fig. 9). 2. Release the lock pin (19). Rotate...
Page 21 Before you start MBCP33-4 Filling up fuel and oil WARNING! This machine is not supplied with petrol-oil mixture in the engine! Before operating this machine it is essential to fill it with petrol-oil mixture! This machine is equipped with a 2-stroke engine. The fuel and oil tank are combined and it is essential to fill a fuel-oil mixture before operating this machine.
Page 22 Before you start MBCP33-4 4. Unscrew and remove the fuel tank cap (5) (Fig. 10). 5. Fill the fuel into the fuel tank (6). Leave approximately 5 mm of space between the top of the fuel and the inside edge of the tank to allow for expansion. Do not overfill (Fig.
Page 23: Quick Start
Quick start MBCP33-4 Operating controls Recoil starter handle Throttle trigger Throttle trigger CLOSE lockout lockout OPEN Throttle Throttle trigger trigger Choke lever Stop Stop switch switch Primer...
Page 24 Quick start MBCP33-4 Preparation Add fuel and oil Assemble mixture Starting cold engine Set stop switch Set the choke Press primer Pull recoil Set the choke to I to CLOSE 6 times starter handle to OPEN 4 times (if engine already...
Page 25 Quick start MBCP33-4 Starting warm engine Set stop switch Set the choke Pull recoil Press and Operate to I to OPEN starter handle release the until engine throttle lockout starts and throttle trigger to let engine run at idle Stopping...
Page 26: In More Detail
Machine function MBCP33-4 Intended use This petrol brush cutter MBCP33-4 is designated with a maximum power output of 1.0 kW. > With the tri-arc blade and cutting-attachment guard attached, the machine is intended to cut heavier weeds, brush and similar vegetation with a thickness of up to 20 mm.
Page 27 Machine function MBCP33-4 Harness NOTE: The harness improves working movement and enables the operator to manage the job in a safer way and takes the strain away from the body. Always wear the harness when working with the machine. Always turn the machine off and wait until the cutting attachment stops completely before taking off the harness.
Page 28: Operation
Machine function / Operation MBCP33-4 Throttle trigger lockout The throttle trigger lockout (14) prevents unintentional start of the throttle trigger (16). The throttle trigger can only be activated if the throttle trigger lockout is pressed (Fig. 15). Press and release the throttle trigger lockout (14) and the throttle trigger (16) will set the engine running at idle speed.
Page 29 Operation MBCP33-4 NOTE: In some countries regulations define at what time of the day and on what special days machines are allowed to be used and what restrictions apply! Ask your community for detailed information and observe the regulations in order...
Page 30 Operation MBCP33-4 Starting cold engine 1. Place the machine on a flat and stable surface. The cutting attachment should not touch ground or any objects. Set stop switch (15) to I (Fig. 16). 2. Set the choke (8) to CLOSE position (Fig.
Page 31 Operation MBCP33-4 3. Hold the machine securely to the ground with your left hand. Pull the recoil starter handle (4) slowly with your right hand until you feel a definite resistance and then give it a brisk, strong pull. Repeat until the engine starts (Fig. 19).
Page 32 Operation MBCP33-4 Trimmer line feeding The string trimmer head (23) is equipped with a bumper help to feed the cutting line (32). Simply tap the bumper on a firm ground while the machine is operating, the spool will release fresh trimming line. A cutting line cutter (31) is integrated with the trimming guard (30) and it cuts the line to necessary length (Fig.
Page 33 Operation MBCP33-4 > Do not lift the cutting attachment higher than your hip. The higher you hold the cutting attachment, the higher the risk of objects being thrown (Fig. 23). Max. height: 300 mm > Avoid cutting tall grass in one cut. Trim taller grass in stages (Fig. 24).
Page 34: Care And Maintenance
Operation / Care and maintenance MBCP33-4 > Hold the cutting attachment just above the ground at an angle of approximately 30° (Fig. 25). > Move the machine with slow and regular motion from left to right before moving it back to the starting position and trimming the next area (Fig. 26).
Page 35 Care and maintenance MBCP33-4 DANGER! Proper maintenance is essential for safe and trouble free operation. Improper maintenance, or failure to address a problem instantly can cause a malfunction which can result in serious injury or even death. 1. Keep the machine clean. Remove debris after each use and before storage.
Page 36 Care and maintenance MBCP33-4 Maintenance table Inspect and maintain this machine regularly based on below maintenance table. Keep the machine in good working condition during maintenance. Part Task Before/after Every 10 hours Every 25 hours each use of operation of operation...
Page 37 Care and maintenance MBCP33-4 3. Form a loop at the middle of the line and insert this loop into the hook on the spool (Fig. 29). 4. Wind the two parts of the cutting line clockwise firmly around the spool (Fig. 30).
Page 38 Care and maintenance MBCP33-4 Air filter Inspect the air filter regularly. Clean or replace it with a new one if necessary. 1. Press the locking tab on the air filter case (9) and open its cover (Fig. 31). 2. Remove the filter and tap it on a stable surface to remove dust.
Page 39 Care and maintenance MBCP33-4 6. Check the spark plug gap. It should be 0.6-0.7 mm (Fig. 32). 7. Replace with a new spark plug if either the electrode or the insulation is damaged. 8. When replacing the spark plug, first screw it in hand tight and then lightly tighten it with the multi-tool I (34).
Page 40 Care and maintenance MBCP33-4 Spare parts/Replacement parts The following parts of this machine may be replaced by the consumer. Spare parts are available at an authorised dealer or through our customer service. Description Model no. or Specification Cutting blade Tri-arc blade: 3 teeth, Ø255 x Ø25.4 mm Cutting line Ø3.0 mm nylon line...
Page 41 Care and maintenance MBCP33-4 Short term storage (less than 1 day) 1. Let the machine cool down before storage. 2. Store the machine as horizontally as possible. Make sure that no fuel-oil mixture can run out of the carburetor. Long term storage NOTE: Risk of machine damage! >...
Page 42: Troubleshooting
MBCP33-4 Troubleshooting Troubleshooting Suspected malfunctions are often due to causes that the operators can fix themselves. Therefore check the machine using this section. In most cases, the problem can be solved quickly. WARNING! Only perform the steps described in these instructions! All further...
Page 43: Recycling And Disposal
Troubleshooting / Recycling and disposal MBCP33-4 Problem Possible cause Solution Engine does not start Spark plug defective? Replace spark plug. Engine cold? Follow cold starting procedure. Carburetor setting not correct? the carburetor. Engine does not reach Incorrect fuel or incorrect...
Page 44: Guarantee
MBCP33-4 Guarantee Guarantee We take special care to select high quality materials and use manufacturing techniques that allow us to create products incorporating design and durability. This product has a manufacturer’s guarantee of 2years against manufacturing defects, from the date of purchase (if bought in store) or date of delivery (if bought online), at no additional cost for normal (non-professional or commercial) household use.
Page 45: Ec Declaration Of Conformity
EC declaration of conformity MBCP33-4 (EN) EU DECLARATION OF CONFORMITY (FR) DÉCLARATION UE DE CONFORMITÉ (PL) DEKLARACJA ZGODNOŚCI UE (RO) DECLARAȚIA DE CONFORMITATE UE (ES) DECLARACIÓN UE DE CONFORMIDAD (PT) DECLARAÇÃO DE CONFORMIDADE UE Product/ Produit/ Produkt/Produsul/Producto/Produto > Brush cutter/Débroussailleuse/Obcinarka do zarośli/Mașina de tuns tufișuri/ Desbrozadora/ Cortador de mato >...
Page 46 EC declaration of conformity MBCP33-4 The object of the declaration described above is in conformity with the relevant Union harmonisation legislation: L’objet de la déclaration décrit ci-dessus est conforme à la législation d’harmonisation de l’Union applicable : Wymieniony powyżej przedmiot niniejszej deklaracji jest zgodny z odnośnymi wymaganiami unijnego prawodawstwa harmonizacyjnego: Obiectul declarației descris mai sus este în conformitate cu legislația relevantă...
Page 47 EC declaration of conformity MBCP33-4 Measured Sound Power Level Guaranteed Sound Power Level Le niveau de puissance acoustique mesuré Le niveau de puissance acoustique garant Zmierzony poziom mocy akustycznej Gwarantowany poziom mocy akustycznej Nivel de putereacusticămăsuratNivel de putereacusticăgarantat Nivel de potencia sonora medido Nivel de potencia sonora garantizado Nível de potência sonora medido...
Page 48 EC declaration of conformity MBCP33-4 (UK) DECLARATION OF CONFORMITY Product • Brush cutter • MBCP33-4 • 33 cm³ , 1.0 kW • 000001 - 999999 Name and address of the manufacturer or his authorised representative: Kingfisher International Products Limited 3 Sheldon Square...
Page 49 Manufacturer, Fabricant, Prodecent, Producător, Fabricante: UK Manufacturer: Kingfisher International Products Limited 3 Sheldon Square London W2 6PX United Kingdom EU Manufacturer: Kingfisher International Products B.V. Rapenburgerstraat 175E 1011 VM Amsterdam The Netherlands www.diy.com www.screwfix.com www.screwfix.ie To view instruction manuals online, visit www.kingfisher.com/products...