200w led profile spot light with zoom, beam shaping shutters & gobo slot (40 pages)
Summary of Contents for CentoLight Square 150P
Page 1
150P 150P quare quare 150W Led Profile Spot Light with Beam Shaping Shutters & Gobo Slot Sagomatore a Led da 150W con ghigliottine e slot per gobo User Manual Manuale Utente Carefully read this manual and properly take care of it Leggete questo manuale e conservatelo per future consultazioni...
Page 2
Dear customer, First of all thanks for purchasing a CENTOLIGHT® product. Our mission is to satisfy all possible needs of light designers and professionals of entertainment lighting, by offering a wide range of products based on the latest technologies. We hope you will be satisfied with this fixture and, if you want to collaborate, we are looking for a feedback from you about product operation and possible im- provements to be introduced in the next future.
Thank you for purchasing SQUARE 150P. Enjoy your new equipment and make sure to read this manual carefully before operation! This user manual is made to provide both an overview of controls, as well as information on how to use them.
1.4. Disclaimer The information and specifications contained in this Manual are subject to change without notice. CENTOLIGHT assumes no responsibility or liability for any errors or omissions and reserves the right to revise or to create this manual at any time.
SQUARE 150P User Manual 3 - M ounTing and igging Pay attention to safety! Please respectively consider the EN 60598-2-17 and the national standard during the installation. Only authorized technicians can carry out the installation. 3.1. Rigging The installation of the fixture must be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming demolition.
4 - i nTroduCTion Centolight SQUARE 150P is a professional LED Profile with 26° beam (also available optional 19° lens tube) designed for theaters and fixed installations where high LED chip reliability and warm white lighting (approx. 3.200K) are required.
3) Power Input/Output Sockets Plug the power-cord included with SQUARE 150P into an AC socket properly config- ured for this fixture. Please read “5.2. About Power Connection” on page 10 for details. This fixture is also equipped with an output power connector to be used as...
SQUARE 150P User Manual tures. Power Input 100-240Vac - 50/60Hz 1st Unit 2nd Unit 3rd Unit 4th Unit 5th Unit 4) DMX Input/Output Sockets DMX Input is a 3-pin male XLR socket for connection to a DMX control device. DMX output is a3-pin female socket for sending the DMX control signal to other units.
SQUARE 150P User Manual DMX machines are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which the machines are connected is not important and has no effect on how a controller communicates to each of them.
SQUARE 150P User Manual 5.5. 3-Pin vs 5-Pin DMX cables DMX connection protocols used by controllers and fixtures manufacturers are not standardized around the world. However, two are the most common standards: 5-Pin XLR and 3-Pin XLR system. If you wish to connect this fixture to a 5-Pin XLR in- put fixture, you need to use an adapter-cable or make it by yourself.
SQUARE 150P User Manual 6.2. Use of Gobo If want to get the Gobo effect on your SQUARE 150P Profile, you need to purchase first the gobo-holder listed below: Model Description J706J SQUARE GOBO-200 Gobo Holder for SQUARE 150P & 6200P Profile Ask your CENTOLIGHT dealer or check out our website www.centolight.com...
J708J SQUARE IRIS-200 Manual Iris for SQUARE 150P & 6200P Profile The manual iris is installed in the same slot used for the gobos. Of course, you have to choose between iris or gobo as they cannot be used simultaneously.
If you choose a starting address that is too high, you could restrict the access to some of the product’s channels. SQUARE 150P uses 2 DMX channels, which de- fines the highest configurable address to 511 to have all channels controllable. This allows you to control of up to 256 units in the 2-channel control mode.
* To contact CentoLight service, see “11 - Warranty And Service” on page 18 or visit www.centolight.com ** For instruction on how to install a DMX terminator, see “5.4. DMX Terminator” on page 11.
SQUARE 150P User Manual 10 - s PeCifiCaTions Light Source 1 x 150W Warm White Citiled® LED Chip Life Over 50,000h CCT (Color Temperature) 3100±150K Luminous Flux 3120lux/3m, 1170lux/5m, 780lux/10m WW≥90 Refresh Rate Over 15.000Hz (Flicker-Free) Framing System 4 adjustable Blades for radial and angle positioning Optics 26°...
Alternatively, you can send the product to CENTOLIGHT SERVICE CENTER – Via Enzo Ferrari, 10 – 62017 Porto Recanati - Italy. In order to send a product to service center, you need an RMA num- ber.
1 - P riMa niziare Grazie per aver acquistato il faro SQUARE 150P. Prima di iniziare, assicuratevi di leg- gere attentamente questo manuale! Esso utente è stato creato per fornire sia una panoramica dei controlli, sia informazioni su come usarli.
1.4. Limiti di Responsabilità Le informazioni e le specifiche contenute in questo manuale utente sono soggette a modifiche senza preavviso. CENTOLIGHT non si assume alcuna responsabilità per eventuali errori od omissioni e si riserva il diritto di rivedere o creare questo manua- le in qualsiasi momento.
Manuale Utente SQUARE 150P 3 - i nsTallazione osPesa Prestare attenzione alla sicurezza! Si prega di fare sempre riferimento alla direttiva EN 60598-2-17 e agli standard nazionali in fase di installazione. Solo personale autorizzato può eseguire l’installazione. 3.1. Installazione Sospesa L’installazione del prodotto deve essere progettata e costruita in un modo che...
4 - i nTroduzione Centolight SQUARE 150P è un Sagomatore LED professionale con fascio luminoso a 26° (disponibile anche tubo con lente a 19° opzionale) progettato per teatri e instal- lazioni fisse in cui è richiesta un’elevata affidabilità del chip LED e un’illuminazione bianca calda (circa 3,200K).
Manuale Utente SQUARE 150P Regolazione Dimmer di precisione a 16-bit Funzionamento Flicker-Free (per applicazioni video) Sistema di raffreddamento a bassa rumorosità Scomparto Gobo/Iris (gobo e iris opzionali) Porta-gelatina Frontale (incluso) 4.2. Dimensioni e Panoramica del Prodotto 590mm (23.29”) 520mm (20.47”) 266mm (10.47”)
Manuale Utente SQUARE 150P 5 - C onfigurazione del rodoTTo 5.1. Descrizione del pannello posteriore 150P QUARE Imported by: FRENEXPORT SPA Porto Recanati (Italy) www.frenexport.com MENU DOWN ENTER Address Dimmer AC100~240V 50/60Hz Il pannello di comando presenta un display LCD da 2x8 caratteri e un’area di fun- zionamento per il controllo dei pulsanti.
Manuale Utente SQUARE 150P Power Input 100-240Vac - 50/60Hz 1st Unit 2nd Unit 3rd Unit 4th Unit 5th Unit 4) Prese di ingresso / uscita DMX L’ingresso DMX è una presa XLR maschio a 3 pin per la connessione a una centra- lina DMX.
Manuale Utente SQUARE 150P dispositivo al DMX IN del dispositivo successivo. L’ordine in cui i fari sono collegati non è importante e non ha alcun effetto su come una centralina comunica a ciascun faro. Utilizzare un ordine che preveda il cablaggio più semplice e diretto.
Accendere l’unità e allentare le manopole di regolazione del fuoco. Quindi regolare la messa a fuoco muovendo avanti e indietro il tubo. 6.2. Utilizzo di Gobo Se si desidera usare dei Gobo nel Sagomatore SQUARE 150P, occorre prima dotarsi del seguente accessorio porta-gobo (opzionale): Modello...
Manuale Utente SQUARE 150P Chiedete al vostro rivenditore CENTOLIGHT o visitate il nostro sito web wwww.cen- tolight.com per ulteriori informazioni. Successivamente, realizzate un gobo da Ø60mm (2.36”) 94mm (3.7”) con l’immagine inversa di ciò che si vuole proiettare. Consultare il disegno a fianco per tutti i dettagli sulla misura minima/massima del gobo.
Manuale Utente SQUARE 150P 121mm (4.76”) Ø100mm Ø79mm (3.94”) (3.11”) 15mm (0.59”) Allentare la manopola del gobo/iris Inserire l’iris all’interno dello scomparto. Accendere il faro, regolare la messa a fuoco fino a che l’immagine del gobo non sia perfettamente nitida.
DMX. Se si sceglie un indirizzo iniziale troppo alto, è possibile che si limiti l’accesso ad alcuni parametri del prodotto. SQUARE 150P utilizza 2 canali DMX, i quali definiscono il più alto indirizzo configurabile a 511 per avere tutti i canali con- trollabili.
I cavi DMX in ingresso e uscita dall’unità e collegarli fra di loro. * Per contattare il Servizio Assistenza Centolight, consultare il paragrafo “11 - Garanzia e Assistenza” a pagina 34 o visitate il sito www.centolight.com ** Per istruzione su come installare un terminatore DMX, vedere “5.4. Terminatore DMX” a pagina 27.
Manuale Utente SQUARE 150P 10 - s PeCifiChe eCniChe Sorgente Luminosa 1 LED Bianco Caldo da 150W CITILED® Ciclo di vita del chip Più di 50.000h CCT (Temperatura Colore) 3100±150K Flusso Luminoso 3120lux/3m, 1170lux/5m, 780lux/10m ≥90 Frequenza di Aggiornamento Oltre 15,000Hz (Flicker-Free)
11 - g aranzia e ssisTenza Tutti i prodotti CENTOLIGHT sono coperti da garanzia di due anni. Essa è valida dalla data di acquisto, come indicato dal documento di acquisto. I seguenti casi/ componenti non sono coperti dalla garanzia di cui sopra:...
Page 35
Questo prodotto viene importato nella UE da FRENEXPORT SPA – Via Enzo Ferrari, 10 - 62017 Porto Recanati - Italy CentoLight® is a registered trademark of FRENEXPORT SPA - Italy CentoLight® è un marchio di fabbrica registrato di FRENEXPORT SPA - Italia...