Do you have a question about the Black Wolf Pro and is the answer not in the manual?
Questions and answers
Summary of Contents for Brunswick Black Wolf Pro
Page 1
Black Wolf Pro™ POCKET BILLIARD TABLE SERVICE DEPARTMENT P.O. BOX 68 BRISTOL, WI 53104 EMAIL: BRUNSWICKSERVICE@BRUNSWICKBILLIARDS.COM 51-906416-001 October 2020...
Page 2
NOTE: Please use the instructions in this manual to assemble the tables shown below. Illustrations may be different depending on the table being assembled. Also note that careful handling of all components will assure damage-free assembly.
Page 3
BASE FRAME AND LEG ASSEMBLY BLACK WOLF PRO FIGURE ONE Step #1: Position the two leg assemblies upside down on a clean protected surface. Step #2: Install the four leg levelers into the bottom of the legs. Thread the levelers all the way into the legs, then back out two full turns.
Page 4
BASE FRAME AND LEG ASSEMBLY (CONTINUED) BLACK WOLF PRO FIGURE THREE 3/8-16 X 1-1/2” HEX HEAD CAP Step #4: Loosely attach the four leg attach brackets to SCREW the top of the legs with 3/8-16 x 1”-1/2” hex head screws 3/8 WASHER and 3/8 at washers.
Page 5
BASE FRAME AND LEG ASSEMBLY (CONTINUED) BLACK WOLF PRO FIGURE FIVE Step #9: Carefully lower base frame over the legs and leg brackets. Step #10: Align clearance holes in attach brackets with clearance holes in the side sills and attach securely with 3/8-16 x 3”...
Page 6
BASE FRAME AND LEG ASSEMBLY (CONTINUED) BLACK WOLF PRO FIGURE SIX S tep #14: Square the base frame by measuring the diagonal corners. Adjust as required. S tep #15: With table in its permanent location, use a precision level to locate the highest corner of the base frame.
Page 7
SLATE ASSEMBLY BLACK WOLF PRO FIGURE ONE Step #1: Position the center slate section evenly between the two base frame cross supports as shown, carefully CENTER SLATE SECTION center the slate section so there is an equal amount of overhang at each side of the base frame.
Page 8
ATTACHING BILLIARD CLOTH TO UNFRAMED SLATE BLACK WOLF PRO Before attaching the billiard cloth, clean slate thoroughly. FIGURE ONE Step #1: Lay the bed cloth over the top of the slate, nap side up. Leave an equal amount of cloth overhang at the ends and sides of the slate.
Page 9
ATTACHING BED CLOTH TO FRAMED SLATE BLACK WOLF PRO Before attaching the billiard cloth, clean slate thoroughly. FIGURE ONE Step #1: Lay the bed cloth over the top of the slate, nap side up, with the nap running from the head end to the...
Page 10
ATTACHING BED CLOTH TO FRAMED SLATE (CONTINUED) BLACK WOLF PRO FIGURE FOUR FOOT Step #11: At location #9, cut a short slit in the cloth at the edge centered on the side pocket opening. Grasp the cloth rmly above this slit, pull the cloth into the side pocket opening and tack or staple to the wood frame.
Page 11
GULLY SYSTEM ASSEMBLY (FOR RETURN SYSTEM TABLES ONLY) BLACK WOLF PRO NOTE: If table is equipped with gully returns, proceed to install in the following manner . FIGURE ONE Step #1: Place the right-hand foot and gully track into position against side and end base frame members.
RAIL ASSEMBLY BLACK WOLF PRO FIGURE ONE 1/4-20 x 1” HEX HEAD BOLT Step #1: Place corner casting upside down on oor. Seat CARPENTER’S SQUARE 1/4” FENDER end and side rail clearance holes onto corner casting WASHER posts. Step #2: Firmly hold end and side rails together, keep them, square by using a carpenter’s square against the...
Page 13
RAIL AND APRON ASSEMBLY (CONTINUED) BLACK WOLF PRO FIGURE ONE #12 x 2” PAN HEAD SCREW Step #1: With the rails remaining face down, attach aprons as shown. Aprons must overhang equally at #12 FLAT WASHER each end. (9/16” O.D.)
Page 14
RAIL AND APRON ASSEMBLY (CONTINUED) BLACK WOLF PRO FIGURE FOUR Step #4: Attach rails securely to table with 3/8-16 x 2-3/ 4” threaded studs, dome washers and 3/8-16 hex nuts. DOME WASHER 3/8-16 HEX NUT FIGURE FOUR FIGURE FIVE Step #5: Position the side pocket pads and corner pocket pads in their respective locations.
Page 15
BALL RECEIVER BOX ASSEMBLY BLACK WOLF PRO FOR RETURN SYSTEM TABLES ONLY FIGURE ONE Step #1: Securely attach the ball receiver box to the base frame end sill as shown with four 1/4-20 x 2-3/4” hex head screws. 1/4-20UNC TEE-NUT 1/4-20 x 2-3/4”...
Need help?
Do you have a question about the Black Wolf Pro and is the answer not in the manual?
Questions and answers