Download Print this page

Advertisement

Quick Links

Advertisement

loading
Need help?

Need help?

Do you have a question about the 9125 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Hosim 9125

  • Page 3 W W W . H O S I M . C O M...
  • Page 6 • WARNING: RISK OF INJURY! Do not stand directly behind the car while driving to avoid personal injury from rocks,sticks, or other thrown objects, especially during full throttle starts. Keep any spectators and animals at a safe distance. Wearing eye protection is recommended.
  • Page 7 Charging and handling precautions • DO NOT let any exposed battery contacts or wires touch each other. This will cause the battery to short circuit and create the risk of fire. • While charging, ALWAYS place the battery on a nonflammable surface such as concrete.
  • Page 8 Precautions • Because your model is controlled by radio, it is subject to radio interference from many sources that are beyond your control. Since radio interference can cause momentary losses of radio control, always allow a safety margin in all directions around the model in order to prevent collisions.
  • Page 9: Speed Control

    Speed control Your model’s electronic speed control (ESC) is an extremely powerful electronic device capable of delivering high current. Please closely follow these precautions to prevent damage to the speed control or other components. • Disconnect the Battery: Always disconnect the battery or batteries from the speed control when not in use.
  • Page 10 MOTOR CARE • Seat the motor brushes by driving smoothly on a flat surface during use of the first battery charge. Failing to do so can greatly reduce motor performance and functional life. • Prolong motor life by preventing overheating conditions. Undue motor wear results from frequent turns, stops and starts, pushing objects, driving in deep water and tall grass, and driving continuously up hill.
  • Page 11 9125 Product Configuration Transmitter DIY Car Shell 7.4V 1600mAh Battery Pack Battery Fireproof Bag T Plug Connector Wheelnut User Manual USB charger LED Lights Battery strap Body clip Hex Wrench...
  • Page 12 Remove The Truck Body Pull out the pins and remove the body Make sure all accessories are properly attached, remove the protection film from the body before turning on the truck. Install LED wire (1).Make the LED wire pass (2).Lock the LED into the front and rear bumper.Connect the through the body bracket.
  • Page 13 Install Transmitter Batteries 1.Remove the battery cover on the bottom of the transmitter(figure 1) 2.Install 3*1.5V AA batteries( not included) in correct polarities (Figure 2) 3.Close the battery cover (Figure 3) Notice: 1.When installing batteries , please be sure to match the polarities labeled on the battery holder.
  • Page 14 Transmitter instructions 1. Turn on the power switch on the transmitter, red LED will flash. (1)Red LED (2)Blue LED 2.When pairing successful with the car, red LED and blue LED will turn solid. A.Power Switch D.Steering Reverse Blue LED will flash when power Switch is low on the transmitter, please B.Steering Trim...
  • Page 15 Transmitter switch instructions A.Power Switch B.Steering Trim When the chassis switch is turned on and the front tires When pairing for the first time,both the car and the are not straight,use the ST.TRIM to adjust the position. transmitter have to be turned on within 3 seconds en the car oversteers to the left , ST.TRIM should be to pair the frequency.
  • Page 16: Operation

    1. ALWAYS turn on your transmitter before you turn on the receiver in the vehicle. Always power off the receiver before turning your transmitter off. 3. WARNING: 9125 waterproof feature, 2. ALWAYS operate your vehicle in a wide open area. Opeating the...
  • Page 17: Troubleshooting

    Troubleshooting Firstly, Plug in the charger 1. Solid red light on the charger = Charger is plugged in. 2. Blinking red light on the charger = Charger is defective. Charger is normal,then plug in the battery 1. Blinking green light on the charger = Battery is Battery/charger plugged in and charging.
  • Page 18 Troubleshooting The RC car comes with a protective plastic film Scratched top that needs to be removed prior to using the car. When the car is moving forward in order to go in reverse please execute the following commands on the remote: Reverse command first throttle push will bring the car to a stop and not responding...
  • Page 19 Troubleshooting 6. Unplug the wires connecting the servo and the ESC, then pair the car with the remote control again. RC car will not pair with the If the car pairs with the remote, then the servo remote might be the problem. If the car still can't pairs with the remote, then the ESC might be the problem.
  • Page 20 6. Servo and remote controller can be ordered through our website www.hosim.com 1. Inspect the car and make sure all the parts are in place and no foreign objects were caught up in Please refer to the schematic in this User Manual to properly check the parts.
  • Page 21 NO.HS-SJ01 NO.HS-SJ02 NO.25-SJ03 NO.25-SJ04 Car shell Car shell Car shell bracket Front bumper block PRODUCT NAME PRODUCT NAME PRODUCT NAME PRODUCT NAME Blue Black SPECIFICATIONS SPECIFICATIONS SPECIFICATIONS SPECIFICATIONS QUANTITY QUANTITY QUANTITY QUANTITY NO.25-SJ05 NO.25-SJ06 NO.25-SJ07 NO.25-SJ08 Front upper arm Rear upper arm Front lower arm Rear bumper block PRODUCT NAME...
  • Page 22 NO.M25-ZJ05 NO.HS-ZJ03 NO.25-ZJ04 NO.M25-ZJ06 Main drive 5 wires servo Differential Shock Absorbers PRODUCT NAME PRODUCT NAME PRODUCT NAME PRODUCT NAME shaft assembly SPECIFICATIONS SPECIFICATIONS SPECIFICATIONS SPECIFICATIONS QUANTITY QUANTITY QUANTITY QUANTITY NO.25-ZJ07 NO.25-ZJ08 NO.25-ZJ09 NO.25-WJ01 Electronic speed Aluminum alloy 2.4G transmitter Arm connector set PRODUCT NAME PRODUCT NAME...
  • Page 23 NO.15-LS08 NO.15-LS14 NO.15-LS09 NO.15-LS10 Countersunk head Round headed screw Round headed screw Round headed screw PRODUCT NAME PRODUCT NAME PRODUCT NAME PRODUCT NAME screw 2.3 x 16PBHO 2.6 x 7PBHO 2.6 x 8KBHO 2.5 x 6 x 5PWMHO SPECIFICATIONS SPECIFICATIONS SPECIFICATIONS SPECIFICATIONS 1X10...
  • Page 25 25-ZJ05 25-ZJ06...
  • Page 30: Warranty Policy

    Warranty policy Warranty policy...
  • Page 31: Customer Service

    Ke ep t his ma n ua l fo r fu tur e re fe re nce . Customer service You can find all replacement parts on our website at WWW.HOSIM.COM If you have any questions about your model or its operation, call HOSIM Customer Support at +1 (989) 430-5314 (EST: 10:00-18:00) E-mail: US@HOSIM.COM CA@HOSIM.COM...
  • Page 32 CE&FCC CE Compliance for Users in the European Union WEEE Compliance: Please help the environment by disposing of your product responsibly at the end of its life. The wheeled bin symbol indicates that this product should not be disposed of in your household waste containers.