Related Manuals for Wasco OPTOOUT-PCIe32 STANDARD
Summary of Contents for Wasco OPTOOUT-PCIe32 STANDARD
- Page 1 OPTOOUT-PCIe32 STANDARD EDP No: A-846600 32 optocoupler isolated digital outputs wasco ® user‘s guide...
- Page 2 ® © Copyright 2019 by Messcomp Datentechnik GmbH This documentation is copyright by Messcomp Datentechnik GmbH. All rights are reserved. Messcomp Datentechnik GmbH reserves the right to modify the products described in this manual at any time and without preannouncement.
-
Page 3: Table Of Contents
8.1 Installing the Linux driver ...................20 8.2 Supported Linux distributions/kernel versions .............20 ® 8.3 Programming of the OPTOOUT-PCIe32 with wasco driver .......20 8.4 Access to the card OPTOOUT-PCIe32 Standard ....................21 8.5 Assignment of the Memory Mapped I/O addresses ..........21 OPTOOUT-PCIe32 ©... - Page 4 ® Table of Contents 9. Accessories ..................22 ® 9.1 Compatible wasco accessories ................22 9.2 Connection Technique (application examples) ............22 9.3 Single components for customized assembly .............23 10. Troubleshooting ................24 11. Specifications ................25 12. Product Liability Act ..............26 13. CE Confirmation ................28 OPTOOUT-PCIe32 ©...
-
Page 5: Description
® 1. Description The wasco ® interface card OPTOOUT-PCIe32 provides 32 digital STANDARD outputs, every single channel is galvanically isolated. Electrical isolation is granted by special high power optocouplers, which can cope with a switching current of up to 150 mA. Additionally, each output is fitted with protection diodes against harmful voltage peaks. -
Page 6: Installing The Optoout-Pcie32
® 2. Installing the OPTOOUT-PCIe32 STANDARD 2.1 Installing the card into your computer Before you insert the card unplug the power cord or make sure, there is no current to/in the computer. Inserting into a running system may cause... -
Page 7: Connectors
® 3. Connectors 3.1 Position of the connector plugs on the board 17.06.2020 13:38 f=1.50 C:\Daten\Layout\Karten\OPTOOUT-PCIe32U\OPTOOUT-PCIe32_v1.02\OPTOOUT-PCIe32_1v02.brd CN1: Optocoupler Outputs OUT00...OUT31 OPTOOUT-PCIe32 © 2019 by Messcomp Datentechnik GmbH EV01 STANDARD... -
Page 8: Pin Assignment Of Cn1
® 3.2 Pin assignment of CN1 OUT31- OUT31+ OUT30- OUT30+ OUT29- OUT29+ OUT28- OUT28+ OUT27- OUT27+ OUT26- OUT26+ OUT25- OUT25+ OUT24- OUT24+ OUT23- OUT23+ OUT22- OUT22+ OUT21- OUT21+ OUT20- OUT20+ OUT19- OUT19+ OUT18- OUT18+ OUT17- OUT17+ OUT16- OUT16+ OUT15-... -
Page 9: System Components
® 4. System Components 4.1 Block diagram +12V +12V Control Logik PCIe Bus Interface OPTOOUT-PCIe32 © 2019 by Messcomp Datentechnik GmbH EV01 STANDARD... -
Page 10: Access To The System Components
The relevant addresses for OPTOOUT-PCIe32 depend on the base address assigned by the BIOS. You can access to the OPTOIO-PCIe32 by double word access only. For reasons of compatibility the wasco dri- vers process or take into account the least significant bytes only. -
Page 11: Optocoupler Outputs
® 5. 32 Optocoupler Outputs Die OPTOOUT-PCIe32 provides 32 output channels, which are galvani- cally isolated by optocouplers. 5.1 Pin assignment of the output optocouplers 5.2 Optocoupler specifications Voltage collector-emitter: max. 50V Voltage emitter-collector: 0,1V Current collector-emitter: 150 mA 5.3 Output circuitry... -
Page 12: Board Identification
® 6. Board Identification 6.1 Board Identification The board Identification enables you to dif- Jumper ferentiate between several PC boards of the same type in your system. This is realised by a software readable jumper block. The board identification to be read consists of one Byte (16 Bit) and is... -
Page 13: Access Via 16 Or 32 Bit
® 6.2 Access via 16 or 32 bit The jumper block JP2/1-2 can be used to set the access width. If the jumper block JP2/1-2 is not set (default), the card operates in com- patibility mode. In this mode, the card is accessed in 16-bit mode. -
Page 14: Programming Under Windows
® ® 7. Programming under Windows ® 7.1 Installing the Windows driver In order to implement the card under Windows ® , it is necessary to install a special driver, which allows access to the card. The operating system ®... - Page 15 ® Once the driver and development files have been installed completely, you will find an icon in the control panel of your computer to localize all wasco ® PCI and PCIe cards existing in the system. OPTOOUT-PCIe32 © 2019 by Messcomp Datentechnik GmbH...
- Page 16 ® ® Start the card query by double-clicking the „wasco “ icon. Following window appears: (An OPTOIO-PCIe16 is used as an example) STANDARD If your card has been detected in the system, the board name, the Board-ID, the I/O address as well as the possible interrupt number of the respective card are displayed in this window.
-
Page 17: Programming The Optoout-Pcie32 With Wasco Driver
After installing the development files of Kithara by means of the setup program the folder wasco contains of the relevant development files and the sample programs. Further sample programs specified for access to the OPTOOUT-PCIe32 you can find on the enclosed CD or please visit our homepage. -
Page 18: Access To The Card Optoout-Pcie32
The access to the OPTOOUT-PCIe32 is done exclusively via board Standard name (card type) WASCO-PCIe8246 7.5 Assignment of the Memory Mapped I/O Addresses The Memory Mapped I/O addresses of the individual hardware compon- ents depend on the base address as follows:... -
Page 19: Compatibility To The Optoout-Pci32
® 7.6 Compatibility to the OPTOOUT-PCI32 STANDARD Developping the OPTOOUT-PCIe32 and its drivers special regard STANDARD was attended to use identical accesses as to the OPTOOUT-PCI32 STANDARD This enables you to change over from PCI to PCIe with existing programs in a very easy way. -
Page 20: Programming Under Linux
® Ubuntu 18.04.4 LTS (Kernel: 5.3.0) 8.3 Programming of the OPTOOUT-PCIe32 with wasco ® driver The programming of the hardware components of the OPTOOUT-PCIe32 is done by accessing the Memory Mapped I/O addresses, which depend on the base address assigned by the system‘s BIOS for the OPTOOUT-... -
Page 21: Access To The Card Optoout-Pcie32
The access to the OPTOOUT-PCIe32 is done exclusively via board Standard name (card type) WASCO-PCIe8246. 8.5 Assignment of the Memory Mapped I/O addresses The Memory Mapped I/O addresses of the individual hardware compon- ents depend on the base address as follows... -
Page 22: Accessories
® 9. Accessories 9.1 Compatible wasco ® accessories Connecting parts EDP-No. KMDB-68 Terminal Module A-492200 DS68R100DS68 Connecting wire (1 meter) A-492400 DS68R200DS68 Connecting wire (2 meter) A-492800 DS68R500DS68 Connecting wire (5 meter) A-494800 9.2 Connection Technique (application examples) DS68R ...*... -
Page 23: Single Components For Customized Assembly
® 9.3 Single components for customized assembly Connection parts EDP No. SCSI-II plug 68-pin for flat ribbon cable A-553200 SCSI-II socket 68-pin for flat ribbon cable A-557200 Slot bracket with cutout for 68-pin connector A-577800 male/female Flat ribbon cable 68-pin A-572800 SCSI-II plug 68-pin für round cables... -
Page 24: Troubleshooting
Please check all settings of your computer or contact your system administrator. (As this are BIOS settings of the computer we cannot expand on this issue. We refer to your systems manual.) Did you install the latest driver version for the wasco ® drivers? Updates you can find here: http://www.messcomp.com... -
Page 25: Specifications
® 11. Specifications Optocoupler Outputs Optocouplers 32* PC853 or compatible socketed 32 channels, galvanically isolated Galvanic isolation even between every single channel with each two se- parate connectors Overvoltage protection by protection diodes Output current max. 150mA Output frequency ca 1 KHz Voltage collector-emitter: max. -
Page 26: Product Liability Act
® 12. Product Liability Act Information about Product Liability The Product Liability Act (Act on Liability for Defective Products - Prod- HaftG) in Germany regulates the manufacturer‘s liability for damages caused by defective products. The obligation to pay compensation can be given, if the product’s pres-... - Page 27 ® * unplug the power plug before you open the unit or make sure, there is no current to/in the unit. * You only may put into operation any components, boards or devices if they have been installed inside a secure touch-protected casing before.
-
Page 28: Ce Confirmation
® 13. CE Confirmation This is to certify, that the product OPTOOUT-PCIe32 STANDARD EDP number A-846600 comply with the requirements of the relevant EMC directives 2014/30/ EU. This declaration will lose its validity, if the instructions given in this manual for the intended use of the products are not fully complied with. - Page 29 ® Reference system for intended use This PC expansion card is not a stand-alone device. The CE-conformity only can be assessed when additional computer components are in use simultaneously. Thus the CE conformity only can be confirmed when using the following reference system for the intended use of the PC...
Need help?
Do you have a question about the OPTOOUT-PCIe32 STANDARD and is the answer not in the manual?
Questions and answers