Do you have a question about the CT1750 and is the answer not in the manual?
Questions and answers
Summary of Contents for ARIES INDUSTRIES CT1750
Page 1
ELECTRIC WOLVERINE (CT1750) Wheeled Electric Cutter Operation and Maintenance Aries Corporate Office: 550 Elizabeth Street, Waukesha, WI 53186 800-234-7205 / 262-896-7205 / Fax: 262-896-7099 Western Regional Office: 5748 East Shields Avenue, Suite 101, Fresno, CA 93727 800-671-0383 / 559-291-0383 / Fax: 559-291-0463...
Page 2
This document contains proprietary and confidential information of Aries Industries, Inc. Copyright 2017 Aries Industries, Inc. All rights reserved. Disclaimer The information contained in this document has been carefully checked and is believed to be entirely reliable and consistent with the products described. However, no responsibility is...
Cutting Motor Lift Up/Lift Down Axis Working Head In/Working Head Out Pipe Clamp Inflate/Deflate Water Control Camera Rotate Up/Rotate Down Camera Brightness Cutting Motor On/Off Tractor Retrieval Maintenance Cleaning/Inspection Returning Equipment Ordering Equipment 970262_A Aries Industries, Inc. ▪ (800) 234-7205 ▪ www.ariesindustries.com Page 2...
Section Two – Drawings and Parts Lists Subject Page CT1750 Cutter Tractor Assembly 380405 Cutter Tractor Assembly w/o Wheels, Arms, or Grind Motor 380629 Main Body Assembly 380629 Main Body Assembly, Bill of Materials 380628 Tip-Up Assembly 380628 Tip-Up Assembly, Bill of Materials...
Page 5
380090 Inner Connect Tow Clevis 380372 Slip Ring Assembly 380958 Common Hardware Kit, Bill of Materials 380685 Oversized Arms & Clutches Kit, Bill of Materials 950637 Spare Parts Kit, Bill of Materials 970262_A Aries Industries, Inc. ▪ (800) 234-7205 ▪ www.ariesindustries.com Page 4...
Page 6
This page was intentionally left blank 970262_A Aries Industries, Inc. ▪ (800) 234-7205 ▪ www.ariesindustries.com Page 5...
Page 7
Section One Operation and Maintenance 970262_A Aries Industries, Inc. ▪ (800) 234-7205 ▪ www.ariesindustries.com Page 6...
Electric Wolverine cutter reel and tractor, the correct air pressure, and proper wheel and extensions arrangements for the pipeline diameter being worked in. The Electric Wolverine cutter tractor may sometimes be referred to as the CT1750. This manual is designed to assist personnel when performing tractor configurations, wheel conversions, and maintenance procedures.
Electric Wolverine Equipment Safety 1. Read and understand the supplied instructions before operating equipment. 2. The CT1750 Electric Wolverine cutter tractor is equipped with powerful cutting motor arms that can pinch, causing injury to fingers or extremities. 3. To prevent personal injury or damage to equipment, turn off and disconnect all power when making adjustments or performing maintenance.
See the Returning Equipment section. If the problems do go away when using the test cables with the cutter tractor and camera, then the cable must be replaced. See the Ordering Equipment section. 970262_A Aries Industries, Inc. ▪ (800) 234-7205 ▪...
Test the previously failed wires from where the termination was cut off to ensure a clean wire path is made between the 970262_A Aries Industries, Inc. ▪ (800) 234-7205 ▪...
Electric Wolverine when not in use. The shipping box should also be used if it is ever necessary to return the Electric Wolverine cutter tractor to Aries for repair. 970262_A Aries Industries, Inc. ▪ (800) 234-7205 ▪...
(P/N 380107) first. The Top Clamp rollers (P/N 380102) can be installed on the Top Clamp strut guide (P/N 380109) before mounting the Top Clamp strut guide (P/N 380109) to the Top Clamp spacer (P/N 380107). 970262_A Aries Industries, Inc. ▪ (800) 234-7205 ▪...
The greater the angle from center, the faster the cutting motor will lift. To lift the cutting motor up, incrementally move the left joystick forward. To lower the cutting motor down, incrementally move the left joystick backward. 970262_A Aries Industries, Inc. ▪ (800) 234-7205 ▪ www.ariesindustries.com...
Turn. Turning this switch to the left will rotate the camera head up. Turning this switch to the right will rotate the camera head down. Returning the switch to center will stop rotation. 970262_A Aries Industries, Inc. ▪ (800) 234-7205 ▪...
This can cause damage to the termination and to the cutter tractor. Always use a pole lift hook or crane assist to lift the cutter tractor out of the manhole. See the Pipeline and Manhole Safety section for more information. 970262_A Aries Industries, Inc. ▪ (800) 234-7205 ▪...
Typical replacement parts over time are O-ring seals, bearings, gears, and fasteners. See the Returning Equipment section for instructions on how to return equipment for repair, or see the Ordering Equipment section for instructions on how to order parts for in house repairs. 970262_A Aries Industries, Inc. ▪ (800) 234-7205 ▪...
2. Product/Item, Description, Quantity, Part Number (Serial Number and Reason for Return when Returning) 3. Contact Name at Aries Industries, Inc. (if applicable) 4. Bill to and Ship to Address 5. Preferred Method of Shipment and an alternate method of shipment 6.
Page 20
This page was intentionally left blank 970262_A Aries Industries, Inc. ▪ (800) 234-7205 ▪ www.ariesindustries.com Page 19...
Page 21
Section Two Drawings and Parts Lists 970262_A Aries Industries, Inc. ▪ (800) 234-7205 ▪ www.ariesindustries.com Page 20...
Need help?
Do you have a question about the CT1750 and is the answer not in the manual?
Questions and answers