SmartDHOME MyOT User Manual
  1. Manuals
  2. Brands
  3. SmartDHOME Manuals
  4. Boiler Supplies
  5. MyOT
  6. User manual

SmartDHOME MyOT User Manual

Interface / actuator for opentherm boilers
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
MyOT interface/actuator for OpenTherm Boilers
User manual and data sheet
Thank you for choosing the interface/actuator for OpenTherm boilers, the latest generation device that allows you to
monitor the performance of the OpenTherm boilers on which it is installed. Z-Wave certified, it is compatible with any
gateway that communicates through this protocol such as MyVirtuoso Home.
www.myvirtuosohome.com
www.smartdhome.com
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MyOT and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for SmartDHOME MyOT

  • Page 1 MyOT interface/actuator for OpenTherm Boilers User manual and data sheet Thank you for choosing the interface/actuator for OpenTherm boilers, the latest generation device that allows you to monitor the performance of the OpenTherm boilers on which it is installed. Z-Wave certified, it is compatible with any gateway that communicates through this protocol such as MyVirtuoso Home.

  • Page 2: General Safety Rules

    Do not use the device in gas saturated environments. Do not place the device near heat sources. Use only the original EcoDHOME accessories supplied by SmartDHOME. Do not place the connection and/or power cables under heavy objects, avoid paths near sharp or abrasive objects, prevent people from walking on them.

  • Page 3: Intended Use

    Description The MyOT interface/actuator for OpenTherm boilers is a fundamental tool for achieving the objectives of Predictive Maintenance, Adaptive Energy Management, qualitative data analysis and remote programming of parameters for proper operation of the systems. It has communication capabilities both through a Sigfox M2M network, through a gateway equipped with a transceiver with Z-Wave protocol, and through Wi-Fi.
  • Page 4 MyOT interface/actuator for OpenTherm Boilers User manual and data sheet The parts of the MyOT interface/actuator for OpenTherm boilers GREEN FUNCTIONS RESET Figure 1: Buttons and LEDs Functions Button: see Wi-Fi configuration and Z-Wave configuration sections. Reset Button: reboot the device.

  • Page 5: Warning Leds

    The green LED signals the status of the OpenTherm connection to the chronothermostat: The MyOT device is connected with the OpenTherm 1 flashing every 3 seconds Thermostat. MyOT works as if it were connected to a 2 flashing every 3 seconds chronothermostat with ON/OFF contact (traditional system).
  • Page 6 For correct device configuration, you need to download and install the IoB application on your smartphone. Then set the MyOT in programming mode by turning on the device and pressing the function key for about 3 seconds. When the button is released, the device will enter configuration, signaling the status with alternating flashing of the LEDs (red and green).
  • Page 7 If you have good experience with this type of device, you can configure MyOT without using the application: Switch on the device.

  • Page 8: Z-Wave Configuration

    Inclusion/Exclusion in a Z-Wave network If you have the Z-Wave version, you can include or exclude the MyOT device in a Z-Wave network. To do this, first of all consult the manual of your gateway to learn how to include and exclude devices. After that it is possible to include/exclude...
  • Page 9 MyOT interface/actuator for OpenTherm Boilers User manual and data sheet COMMAND_CLASS_THERMOSTAT_SETPOINT This CC can be used to manage the boiler setpoints. N.B. The maximum and minimum value of the setpoints are displayed with the COMMAND_CLASS_CONFIGURATION. This was done to support a non-exclusion/inclusion boiler hot swap. It is also important to know that setting the heating setpoint to 0 is equivalent to setting it to the maximum reported by the boiler.

  • Page 10: Warranty And Customer Support

    Enabling DHW (0: no 1: yes) Error flag if present (0 otherwise) Error code if present (0 otherwise) COMMAND_CLASS_SECURITY MyOT device supports unauthenticated S0 and S2 security. Warranty and customer support Visit our website at the link:http://www.ecodhome.com/acquista/garanzia-eriparazioni.html If you encounter technical problems or malfunctions, visit the site: http://helpdesk.smartdhome.com/users/register.aspx...
  • Page 11 MyOT interface/actuator for OpenTherm Boilers User manual and data sheet SmartDHOME Srl V.le Longarone 35, 20080 Zibido San Giacomo (MI) info@smartdhome.com Product Code: 01335-2080-00 Rev. 06/2021...

This manual is also suitable for:

01335-2080-00

Table of Contents