Wavlink WL-WN523N2 Quick Start Manual

QUICK START GUIDE
300Mbps Wi-Fi Range Extender
WL-WN523N2
WAVLINK (@WavlinkOfficial)
WL-WN523N2x2
WAVLINK SUPPORT (@WavlinkTechSupport)
Wi-Fi Repeater Mode
OPTION ONE
Using a Web Browser
1 2
Power ON Connect to the Device
1.
Plug the Device into an electrical outlet near your
For Windows User
Wi-Fi router.
2.
Wait until the POWER LED is on and solid green.
Not connected
Wireless Network Connection
WAVLINK-N
1.
Disconnect the Ethernet (Wired) connection
from your laptop (if any).
2.
Turn your laptop's Wi-Fi ON if it is OFF.
3.
Click the Wi-Fi icon on the taskbar and connect
to the Device's network: WAVLINK-N.
4 Relocate
1.
Plug the Device into an electrical outlet about halfway between your router(Host Wi-Fi) and the Wi-Fi dead zone. The location you
choose must be within the range of your existing host Wi-Fi.
2.
If the signal is weak, relocate it closer to the router to achieve a good (or better) signal quality.
Tips: Use your phone to find the ideal location for the Device.
If your phone's Wi-Fi signal(received from your router) is higher
than 3 levels, it is the ideal spot to install the Device. If not, we
suggest you to move closer to your router for better Wi-Fi signal.
Introduction
The Device is mainly used for providing free Wi-Fi service in big area such as
actory, community, street or etc. The Device can take an existing 802.11n
wireless signal, repeat and extend it to a longer range where it is too far away
for the router or access point to reach. The device supports 2.4G wireless
network connection, and it can supports 2.4G transmission speeds of up to
300Mbps. It has two internal antennas which provide even better wireless
performance, transmission rates. Stability technology automatically avoids
channel conflicts using its channel selection feature.
For Mac OS X User
Wi-Fi:On
Turn Wi-Fi Off
WAVLINK-N
Connections are available
Join Other Network....
Create Network....
Open Network Preferences...
Connect automatically Connect
1.
Disconnect the Ethernet (Wired) connection
from your laptop (if any).
2.
Turn your laptop's Wi-Fi ON if it is OFF.
3.
Click the Wi-Fi icon on the top right corner
of the screen, and connect to the Device's
network: WAVLINK-N.
Hardware Overview
8
9
5
6
7
1
2
3
4
Default Parameters
- Default IP: 192.168.10.1 - URL: http://ap.setup
- Wi-Fi key: no
- Login Password: admin
- Wi-Fi SSID: Wireless-N
3 Configure
3
1.
Launch a web browser and type http://ap.setup
in the address field. Enter admin (all lowercase)
to login.
Wi-Fi Range Extender
English
login
If the login window does not pop up, please
refer to the FAQ > Q1.
4.
Verify your wireless settings and click "Connect".
Host Wi-Fi
WPS Button LED Indicators
1
Reset Button
2
WAN/LAN Port
3
ON: The Device is powered on
POWER
LAN Port
4
OFF: The Device is not receiving electrical power.
LAN LED
5
6
WAN/LAN LED ON: The Ethernet port is connected.
LAN/WAN OFF: The Ethernet port is disconnected.
7
WPS LED
Flashing: Transferring data to/from a network device
8
Wi-Fi LED
9
Power LED
Slow Flashing: The Device is trying to connect to your PC or Phone
WPS
Fast Flashing: The Device is connecting to your AP/Router
WPS Button:
Press and hold for 2 seconds, the Device is trying to connect to your PC or Phone
Press and hold for 6 seconds to connect to your Wi-Fi AP/Router
Reset Button: Press and hold for 3 seconds to
2. 3.
Click "Wizard". Select a Wi-Fi SSID of your router (Host Wi-Fi) and enter
the password. Either keep the same SSID as your host
Wi-Fi or create a new name for the extended network.
Repeater
Connect to:
This Device Router
Wi-Fi Password:
Speed Clients Internet
Repeater SSID:
0 KB/S 1
Disconnet
0 KB/S
Device Information
WAN Type Repeater Wi-Fi SSID Wireless-N
Device IP 192.168.10.1 Channel 11
Gateway 192.168.10.1 Connect to NONE
DNS1 0.0.0.0 Status Disconnect
DNS2 0.0.0.0 Up Time 00h:10m
WAN MAC 82:3F:5D:09:EA:62 Firmware M78N_V3130.1121
Status Wizard Wi-Fi Setup
Status
(for Repeater Mode)
Reset the Device.
Repeater Wizard
Host Wi-Fi Name
Wavlink_530
Host Wi-Fi Password
********
Extended Network Name
Wavlink_Extend
Connect
Select a Wi-Fi Manually enter
Wavlink_530
Wireless-562
Wireless-N
Wireless-112
Wireless-MO
Wizard Wi-Fi Setup