Advertisement
Quick Links
Verify part and application is correct before proceeding.
If missing part or damage item please customer service directly.
We strongly recommend reading through the installation
ARMORDILLO RECOMMENDS PROFESSIONAL INSTALLATION ON ALL THEIR PRODUCTS
WARNING:
When working on ,under or around vehicle exercise caution. If working without a lift check vehicle owners manual for correct jacking points.
Always wear safety glasses and ensure a safe working area. Serious injury or death could occur if safety measures are not followed.
PERIODICALLY CHECK TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUND
CARE
To protect your investment, wax this product after installing. Regular waxing is recommended to add a protective layer over the
finish. Do not use any type of polish or wax that may contain abrasives, that could damage the finish.
For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish.
Mild soap may be used to clean bull guard.
For color finishes: Regular waxing is recommended to add a protective layer over the finish.
Mild soap may be used to clean the bull guard.
ARMORDILLO products are designed as decorative accessories and should not be relied upon as protection for the vehicle or passengers. Buyers assume all
risk and liability whatsoever resulting from installation and use of ARMORDILLO products. ARMORDILLO assumes no liability for injury, loss, incidental or
consequential damages in the event of an accident.
ARMORDILLO guarantees the original purchaser a LIMITED 5 YEAR WARRANTY from data of purchase against manufactured defects in materials,
workmanship and finish under normal use. This excludes damage resulting from road hazards, debris, product misuse, improper installation, impairments from
accidents, neglect, shipping or product modification. This warranty applies only to new products and is limited to the repair or replacement of ARMORDILLO
products. Warranty does not included cost of removal, installation, labor, freight, inconvenience, or consequential damage. Original purchaser must return
defective merchandise to the original place of purchase and must provide the proof of purchase.
21912 Garcia Ln, Walnut, CA 91789
WWW.ARMORDILLOUSA.COM
CR 2 Chase Rack
Monday - Friday 9am-6pm PST (909)895-4522
Email - SUPPORT@ARMORDILLOUSA.COM
guide before installation.
STOP
IMAGE IS FOR REFERENCE,
SHOWN WITH ADDITIONAL ACCESSORIES
(909) 895-4522
SUPPORT@ARMORDILLOUSA.COM
1/2020 2000 REV2
Advertisement
Summary of Contents for ARMORDILLO CR 2
- Page 1 Mild soap may be used to clean the bull guard. ARMORDILLO products are designed as decorative accessories and should not be relied upon as protection for the vehicle or passengers. Buyers assume all risk and liability whatsoever resulting from installation and use of ARMORDILLO products. ARMORDILLO assumes no liability for injury, loss, incidental or consequential damages in the event of an accident.
-
Page 2: Parts List
PERIODICALLY CHECK TO ENSURE ALL FASTENERS ARE TIGHT A ND ALL STRUCTURAL COMPONENTS ARE SOUND Armordillo USA warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, We may repair or replace the product at their option, when the product is returned, prepaid, with proof of purchase. - Page 3 INSTALLATION WALKTHROUGH: READING INSTRUCTIONS THOROUGHLY AND COMPLETELY BEFORE BEGINNING INSTALLATION. WE ARE NOT RESPONSIBLE FOR ANY DAMAGE OR FAILURE RESULTING FROM IMPROPER INSTALLATION. 1) Lay out the parts on protected surface to prevent damage to the chase rack finish. Locate the mount point on the Driver side panel and middle section, Connect the driver side panel and middle section as shown with provided hardware by placing (3) M10X25mm button head bolt and (3) M10 Washer thru the hole on the driver side panel attaching it to the middle section panel with (3) M10...
- Page 4 INSTALLATION WALKTHROUGH: 6) With the chase rack installed on the vehicle attached the 3rd brake light holder to the chase rack. There are 2 mount points on the cross bar that is closed the rear of the bed. Attach the #rd bracket light holder with the supplied hardware, (2)M8 Hex bolt, M8 Washer on the top and on the bottom it will be (2) M8 washer, (2) M8 Lock Washer and (2) M8 Hex nut 7) The 3rd brake light is pre installed on the shroud, The wires are recommend to be tap into your...
- Page 5 INSTALLATION WALKTHROUGH: 21912 Garcia Ln, Walnut, CA 91789 (909) 895-4522 WWW.ARMORDILLOUSA.COM SUPPORT@ARMORDILLOUSA.COM 1/2020 2000 REV2...
- Page 6 Wiring Information WARNING This is meant for informational purposes only! DO NOT ATTEMPT ANY WIRING OF ANY KIND if you lack the knowledge and understanding required. Otherwise personal injury and/or death as well as property damage or loss could occur. Electricity is dangerous and can cause personal injury or DEATH as well as other property loss or damage if not used properly.
Need help?
Do you have a question about the CR 2 and is the answer not in the manual?
Questions and answers