Summary of Contents for MC Clean+ FM430
- Page 1 Operator’s Manual FM430/FM510 Multifunction Scrubber ● Please read this Operator’s Manual carefully and make sure fully understand before using the appliance. ● Please keep this Manual for future reference.
-
Page 2: Table Of Contents
CONTENTS 1.0 Operate Safety Instruction 2.0 Machine Introduction 2.1 Accessories 2.2 Technical Specifications 2.3 Technical Change 3.0 Prepare the machine before operation 3.1 How to install the Brush and Pad Driver 3.2 How to adjust the Handle 4.0 Power connection 5.0 How to operate the machine 5.1 How to start/stop the machine 5.2 How to control the machine... -
Page 3: Operate Safety Instruction
Operate safety instruction Please read this manual carefully before using this appliance In this manual, there are common safety instructions in details on appliance preparing, operating and maintenance. And operator must obey these accident preventive regulations when use this machine. Any accident aroused by regulations disobey, producer will not bear any liability. - Page 4 Electrocution could occur if maintenance and repairs are performed on a unit that is not disconnected from the power source. Disconnect the power supply before attempting any maintenance or service. Always remove the electrical plug from the electrical outlet before changing the brush, pad or other attachment and before leaving the machine.
-
Page 5: Accessories
The appliance is heavy. Get assistance before attempting to transport or move 2.0 Machine instruction FM430 Single Disc Scrubber is a multifunction floor scrubber appliance, it is favorable in strong adaptability, simple reliable construction, smooth working, huge measurement of solution tank, this appliance can basically meet the cleaning requirement on hard floor for the professional cleaning company. -
Page 6: Technical Change
2.2 Technical Data MC Multifunction Floor Scrubber TYPE FM430 POWER(W) 1100 VOLTAGE(V) 110V FREQUENCY(Hz) BRUSH PLATE DIA.(in) PAD DRIVER DIA.(in) BRUSH PLATE ROTATION SPEED(rpm) CABLE LENGTH(m) WEIGHT(lbs) 2.3 Technical Changement MC preserves rights to improve the technology without prior notice. So, the machine may not match these manuals, figures completely. - Page 7 How to prepare the machine for operation Please pull off the power plug from electrical outlet before installing or replacing the pad driver, brush and other attachments. How to install brush or pad driver To install brush pad, follow the steps on below: 1,Pull the level in Figure 1, and adjust the handle in the suitable position for you, 2,Tilt the machine backward until the handle touches the...
-
Page 8: How To Adjust The Handle
3.2 How to adjust the handle To adjust the handle, please follow the steps below: 1. Pull up the level in Figure 1, and adjust the handle 2. Lower the handle to the best operating position NOTE: For the best operating position, keep your back straight, bend only your arms. -
Page 9: How To Operate The Machine
5.0 How to operate the machine 5.1 How to start/stop the machine Never start the appliance when the handle is vertical position. Also a start lock construction is designed, in order to avoid mistake operating when the handle is in vertical position. Both hands should be hold on the handle when start the appliance Start the appliances based on following steps, see Figure 4: 1,Pull up the level, adjust the handle to your suitable position. -
Page 10: Maintenance
So take care. For safe operation, and longer life to your MC product, use only MC parts. The grease for the gear box needs to be changed every year. FM430/FM510 floor scrubber should add about 250ml lubrication grease. - 10 -... -
Page 11: Common Malfunction Diagnosis
7.0 Common malfunction diagnosis Before asking for amendment and examination, please check based on the following points. If the malfunction can not be eliminated, please contact the amendment center or local sale agency. Problem: Possible Cause: Solution: Power cable looses/falls off Check all the power cable connection Motor operates Power cable is broken...
Need help?
Do you have a question about the FM430 and is the answer not in the manual?
Questions and answers