Summary of Contents for ESB AUDIO TREMILA 3000 Series
- Page 1 3000 eries nstallation Manual esbcar.com esbcar.com/3000-series Specifications may change without notice.
- Page 2 3.25 1”/25 mm weeter Installation Manual M IN FE TURES TECHNIC L SPECIFIC TIONS • 25 mm voice coil • Power handling: • Neodymium magnet N42 type 160 W peak, 50 W continuous • Light vented aluminum former • Frequency response: •...
- Page 3 The ESB 3.25 tweeter can be installed with different solution, this depend of car fter removed the ring you can place the tweeter in a 43 mm diameter hole in a type, factory location and tweeter position or listening angle. First solution is to car panel (max 4 mm thickness).
- Page 4 3.28 1.1”/28 mm weeter Installation Manual M IN FE TURES TECHNIC L SPECIFIC TIONS • 28 mm voice coil • Power handling: • Nominal diameter 32.8 mm 180 W peak, 90 W continuous • Neodymium magnet N42 type • Frequency response: •...
- Page 5 The ESB 3.28 tweeter can be installed with different solution, this depend of car Basic mounting system is to use the four llen screws and fix the 3.28 by the 4 type, factory location and tweeter position or listening angle. First solution is to mounting holes from face-plate.
- Page 6 3.UM 2-Way Mid-High Unit Installation Manual M IN FE TURES TECHNIC L SPECIFIC TIONS • 25 (Tw)/20 (mid) mm voice coil • Power handling: • High temperature aluminum/copper 120 W peak, 60 W continuous voice coil • Frequency response: • xial forced ventilation 100 Hz - 25 KHz +/- 3dB •...
- Page 7 This speaker unit can be installed in -pillar, kick panel, or in the car’s door. Remove the speaker and drill 2 mm holes at each mark. Connect the speaker wires, observing correct polarity, and be sure wires don’t touch any metal part. -Pillar: The mounting in the -pillar has too many variables depending on the Make sure the speaker is secured so that air does not leak around the mounting shape of the car to be briefly described.
- Page 8 3.65 2.5”/65 mm iderange Installation Manual M IN FE TURES TECHNIC L SPECIFIC TIONS • Copper/aluminum 20 mm voice coil • Power handling: • FE motor optimized 120 W peak, 60 W continuous • luminum former • Frequency response: • Neodymium magnet N42 type 100 Hz - 22 KHz +/- 3dB •...
- Page 9 Factory Location: Your new speakers have been designed to install into most Remove the speaker and drill 2 mm holes at each mark. Connect the speaker vehicles that accept a 2.5”/65 mm speaker. It is absolutely vital that the speaker wires, observing correct polarity, and be sure wires don’t touch any metal part.
- Page 10 3.90 3.5”/90 mm idrange Installation Manual M IN FE TURES TECHNIC L SPECIFIC TIONS • Copper/aluminum 20 mm voice coil • Power handling: • FE motor optimized 120 W peak, 60 W continuous • High temperature aluminum former • Frequency response: •...
- Page 11 Factory Location: Your new speakers have been designed to install into most vehicles Remove the speaker and drill 2 mm holes at each mark. Connect the speaker that accept a 3.5”/90 mm speaker. It is absolutely vital that the speaker frame fits into wires, observing correct polarity, and be sure wires don’t touch any metal part.
- Page 12 3.165 6.5”/165 mm id-Woofer Installation Manual M IN FE TURES TECHNIC L SPECIFIC TIONS • Copper/aluminum 25 mm voice coil • Power handling: • FE motor optimized 240 W peak, 120 W continuous • High temperature aluminum former • Frequency response: •...
- Page 13 Factory Location: Your new speakers have been designed to install into most vehicles Remove the speaker and drill 2 mm holes at each mark. Connect the speaker that accept a 6.5”/165 mm speaker. It is absolutely vital that the speaker frame fits into wires, observing correct polarity, and be sure wires don’t touch any metal part.
- Page 14 3.69 6 x 9”/150 x 230 mm oofer Installation Manual M IN FE TURES TECHNIC L SPECIFIC TIONS • Copper/aluminum 25 mm voice coil • Power handling: • FE motor optimized 240 W peak, 120 W continuous • High temperature aluminum former •...
- Page 15 Factory Location: Your new speakers have been designed to install into most vehicles Remove the speaker and drill 2 mm holes at each mark. Connect the speaker that accept a 6x9”/150x230 mm speaker. It is absolutely vital that the speaker frame wires, observing correct polarity, and be sure wires don’t touch any metal part.
- Page 16 3.165 6.5”/165 mm onvertible Speaker Installation Manual M IN FE TURES TECHNIC L SPECIFIC TIONS • FE motor optimized • Power handling: • 25 mm copper/aluminum voice coil 240 W peak, 120 W continuous • High temperature aluminum former • Frequency response: •...
- Page 17 Crossover Network: The crossover terminals area are separated as red zone and black zone: all connectors on red zone are positive (+) and all connectors on black zone are negative (-). Wires from the amplifier outputs must be connected on terminal labeled IN+ and IN-.
- Page 18 3.69 6 x 9”/150 x 230 mm onvertible Speaker Installation Manual M IN FE TURES TECHNIC L SPECIFIC TIONS • FE motor optimized • Power handling: • 25 mm copper/aluminum voice coil 240 W peak, 120 W continuous • High temperature aluminum former •...
- Page 19 Crossover Network: The crossover terminals area are separated as red zone and black zone: all connectors on red zone are positive (+) and all connectors on black zone are negative (-). Wires from the amplifier outputs must be connected on terminal labeled IN+ and IN-.
- Page 20 3.6K2 X 2-Way Passive rossover Installation Manual M IN FE TURES TECHNIC L SPECIFIC TIONS • Dedicated to 3000 series speakers • Power handling: • Large screw terminal 300 W peak, 150 W continuous • Ventilated case • Crossover cut-off: •...
- Page 21 The crossover should be installed in a dry location inside your vehicle. It can be CROSSOVER NETWORK DJUSTMENT screwed into a solid surface via all 4 holes located under the protective cover of the case. To access these holes, remove the 4 llen screws and pull the cover away tweeter level can be adjusted on 4 steps by first jumper on right side.
- Page 22 3.6K3 X 3-Way Passive rossover Installation Manual M IN FE TURES TECHNIC L SPECIFIC TIONS • Dedicated to 3000 series speakers • Power handling: • Large screw terminal 300 W peak, 150 W continuous • Ventilated case • Crossover cut-off: •...
- Page 23 The crossover should be installed in a dry location inside your vehicle. It can be CROSSOVER NETWORK DJUSTMENT screwed into a solid surface via all 4 holes located under the protective cover of the case. To access these holes, remove the 4 llen screws and pull the cover away midrange level can be adjusted tweeter level...
Need help?
Do you have a question about the TREMILA 3000 Series and is the answer not in the manual?
Questions and answers