Advertisement
Advertisement
Table of Contents
Summary of Contents for ZINCKER VAULTA K1
- Page 1 Electronic Door Knob...
-
Page 2: Customer Support
For now, please be sure to explore all of its features outlined in this manual. If you have any questions, feel free to just drop us an email anytime. We’d love to assist you to the get the most out of it! CUSTOMER SUPPORT support@zincker.com www.zincker.com... -
Page 3: What's In The Box
What’s in the Box Screw Interior Cover Interior Assembly Battery Compartment Cable Wire Latch Assembly Rod Bolts Strike Plate Square Spindle Exterior Assembly USB-C Port... - Page 4 Tools Parts Phillips Screwdriver Additional Exterior Assembly Interior Assembly Latch Assembly Key x 2 Strike Plate Drill Hole Saw Drill Chisel Hammer M4 Screws x 2 M4 Screws x 2 M4 Screws x 1 Strike Plate 2-1/3” (60mm) 1-1/2” (40mm) 1/2”...
- Page 5 Prepare the door and check dimensions For installation on new doors 1. Prepare door and jamb a. Take out the ‘Door Marking Template’ (Figure 1a). b. Fold template and place on door 36” (915mm) from the ground as marked (Figure 1b). -1a- -1b- 2.
- Page 6 3. Drill and chisel door a. Drill 2-1/8” (54mm) hole through door face as marked for lock set (Figure 3a). -3a- -3b- b. Drill 1” (25mm) hole in center of door edge for Latch Assembly (Figure 3b). c. Insert Latch Assembly in hole keeping it parallel to face of door. Mark outline and remove latch (Figure 3c).
- Page 7 For installation on doors with pre-drilled holes 1. Check door compatibility / Remove existing door knob (if applicable)
- Page 9 2. Double check door dimensions Backset: measure to confirm that the Thickness: measure to confirm that the door backset is either 2-3/8" or 2-3/4" (60 or 70mm). is between 1-3/8" to 2.5" (35mm to 65mm) thick. Hole in the door: measure to confirm Hole in the door edge: measure to confirm that the hole in the door is 2-1/8"...
- Page 10 DO NOT use an electric screwdriver, only hand tighten screws with Phillips screwdriver. DO NOT over-tighten screws. DO NOT install this product if your door thickness is out of range.
- Page 11 Install the latch and strike plate Hold the latch in front of the door hole, with the latch face flush against the door edge. Make sure the square-shaped hole is centered. For 2-3/4“ (70mm) backset, pull to extend the latch in order to center the squared-shaped hole.
- Page 12 Install the latch using screws. Facing door Jamb In most cases, the existing strike plate is ready to be used. You may store the strike plate in box for future use. If not, please make sure the bolt is aligned correctly with the strike plate.
- Page 13 Install the Exterior Assembly Make sure the door is open. Make sure the keyhole is in vertical position. Insert the Exterior Assembly onto the door with the rod bolts going through the round holes on the latch, and the square spindle and the control wire going through the square-shaped (center) hole. Forcing the control wire into any other place than specified above will...
- Page 14 Install the Interior Assembly Remove the screw on top and then pull out the cover. Plug the control wire male plug to the female socket located on the battery compartment. Install interior knob onto the door with the rod bolts going through the round holes on the latch, and the Install the batteries into the compartment.
- Page 15 Testing door knob Always test with door open. Enter admin passcode 123456 (default) > and test the exterior knob. The bolt should move smoothly in and out. Use keys to test the exterior knob. The bolt should move smoothly in and out. Test the interior knob.
- Page 16 Using door knob Enter button Indicator light Green Indicates a setting is successful and activated Unlocking successful Indicates a setting is unsuccessful and deactivated Low-battery warning USB-C Port Batteries Electronic lock requires 4 AA Alkaline batteries (Duracell or Energizer recommended) to be purchased separately.
- Page 17 Buzzer and Status Indicator Action Buzzer Indicator Power on Long beep Stays green for a while Press a button Beeps once Blinks green once Unlocking successful Long beep Stays green for a while Passcode operation successful Long beep Stays green for a while Silent mode on Silent Stays green for a while...
-
Page 18: Account Management
Account management Default administrator passcode is ‘123456’. If you wish to set a new Administrator Passcode passcode, it should be 4-8 digits. Make sure to set a new code as soon as you finish installing the lock. > old passcode > >... - Page 19 Settings Remove the screw and cover from the interior assembly. Press and hold the Reset Button until you hear a long beep sound Resetting the Door Knob along with the green light, and then the door knob will reboot itself until you hear another long beep sound along with green light, indicating the reset is successful.
- Page 20 The door knob will automatically lock after 5s. NOTE: Turning on Passage Mode will automatically disable the Auto-Lock Auto-Lock feature. As soon as Passage Mode is off, Auto-Lock will resume automatically. Turn on/off Silent Mode (Buzzer) Silent Mode > admin. passcode > >...
-
Page 21: Troubleshooting
Troubleshooting 1. Remove the cover from the interior assembly and then check if the cable wire is securely attached. If not, remove the connector and then plug in again. 2. Make sure the batteries are inserted properly (correct polarity). No indicator nor sound 3. - Page 22 1. Check the size of the hole in the door edge and adjust according to installation guide. Latch will not extend or 2. Check if the latch is installed properly according to the retract completely when backset length. closed 3. Make sure the thinner edge of both the interior and exterior knobs heads downward and vertically to the floor.
-
Page 23: Important Safeguard
Important safeguard Protect your administrator code (less exposure) by setting a user code aside from the administrator code for daily use. Use only administrator code when you need to manage users. When sending a user code, always double-check that you are sending it to the correct recipient. Dispose of used batteries according to local laws and regulations.