Page 1
Manufacturers of PP strap, machinery & packaging Accesories. Manual de uso User guide V07/21...
Page 2
INDEX Translated from Spanish Introduction. Technical machine specifications and noise emissions. Main components. 3.1. Spool holder hoop. 3.2. Spool holder. 3.3. Access door. 3.4. Control panel. 3.5. Footswitch. Safety instructions. Set up. Electrical panel operating. 6.1. Master switch. 6.2. Emergency stop button. 6.3.
Page 3
We thank you for choosing the NELEO 50, 90 machines. This well-known model is technologically advanced and easy to manage. For a better development of your NELEO 50, 90 machines, please read carefully this manual. It is the customer responsibility that all staff allowed to work with this machine and maintenance technicians read and understand this manual, especially the safety instructions.
Page 4
Maximum noise level 70 dB In compliance with annex 1 of the Machinery Directive 2006/42/CE, Plasticband, S.A. declares that the noise emitted by this machine is within the limits of the above mentioned legislation which provides a maximum of 70dB (A).
Main components 3.1 Spool holder hoop It is the rotation element that wraps the product on which the spool holders are mounted. It is mounted on four or five bearings (depending on model) for silent running, driven by an electric motor via a V-belt of low maintenance and wear.
3.4 Control panel It is provided with all the control elements: Panel control with different push-buttons, pilot lamps, and an emergency stop push-button with a red visual signal. 3.5 Footswitch The pedal is covered by a protection to avoid the machine to starts unintentionaly.
Safety instructions The wrapping machine NELEO 50, 90 has been designed and made to guaranty the maximum safety during its use. 1. Before using this machine, consult the manual use. 2. Do not work in explosive environment. 3. Do not use water o water steam to clean the machine.
Electrical panel operating CONTROL PANEL - The panel control is placed in the left-hand side cover and its compossed of: 6.1 Master switch Push botón (ON/OFF): it operates as master switch. 6.2 Emergeny stop button This button is placed in the upper part of the machine. In any situation, just pressing this button will stop automatically the machine.
6.3 Control speed It is the speed regulator of the spool holder, with which you can adjust the density of stretchfilm to put onto the products. Increases or decreases the speed of the hoop (faster/lower work). 6.4 Reset button The Reset button is a safety system which avoids machine working after a tension fail.
Page 10
Important: For the proper functioning of the machine, insert the coils tubes to the end of the spool holder to prevent possible damage to internal components of the machine. Plasticband recommends working with two coils simultaneously and keep them with a similar amount of film in order to prevent the machine from moving while turning at high speed.
Page 11
machine and the film is threaded. Optionally, to save time, you can hold the ends of the stretch film to wrap the product with your hand and press the pedal. When you release the pedal, the coils are automatically threaded. Stretchfilm tension adjustment To reach the wished stretchfilm tension, it will be enough by turning round the tension control (see...
Page 12
Package dimension adjustment To peach an optimal packaging is important to adjust the position of the gravity rollers tables. To adjust the height of the gravity rollers table to lose the handle (see picture) placed under the tables and adjust them to the desired height.
Review of screwed unions. 3 months Spool holder Maintenance Revise and clean the traces of 1 month stretchable film. Greasing Maintenance According to description. 6 months Perform a general review and maintenance of the machine every 12 months for Plasticband’s after-sales service. V07/21...
Page 14
Ring bearings guide. Important: Do not put grease in the belt guide, it could cause that belt slide as well as that ring would not turn. PLASTICBAND AFTER SALES CUSTOMER SERVICE Phone: +34 938 495 722 Mobile phone: +34 630 299 839 service@plasticband.com...
Page 15
Breakdowns SYMPTOM: Machine blockaded. CAUSE SOLUTION 1. Some safety device activated. 1. Push RESET button. Check that window is closed. 2. Blockade of the frequence variator. 2. Stop the machine for 20 seconds. 3. Automaton (PLC) out of sequence. 3. Stop the machine for 20 seconds. 4.
Page 16
Component list and spare parts 10.1 Components list • Framework set • Transmission set • Spool holder set • • Safety closing set Control panel Optionals • Gravity rollers table • • Cutter set Short products bridge • Manual top presser •...
Need help?
Do you have a question about the NELEO 50 and is the answer not in the manual?
Questions and answers