Summary of Contents for Q-DIS FIAT-LI
- Page 1 Installation Manual Multimedia Interface for Fiat / Jeep U-Connect 7inch / 8.4inch 2015~ FIAT-LI NON COLLEGARE IL CANBUS NO LINEE GUIDA STERZANTI...
-
Page 2: Specification
Specification Compatibility: Fiat/Jeep 2015~2020 U-CONNECT 7inch / 8.4inch Fiat 500 (L & L Pro) / 500X / 500 Cross / Tipo / Jeep RENEGADE Cap. T/S monitor * Currently, Not Support OEM Cap. T/S Function Interface Input / Output specification : Input: LVDS IN x1 CVBS(Front Camera) x1... -
Page 3: Main Board
Components LVDS CABLE POWER/CAN CABLE MAIN BOARD HLVDSC0069 HPOWER0282 QCPASS1672 FFC Cable 40P SUB BOARD Ext. BOARD FFCBAL0073 QCPASS1680 QCPASS1692 FFC Cable 30P FFCBAL0064 REMOTE CTRL. IR CABLE REMOTE0001 HIRCAB0002... -
Page 4: Cable Connection
Cable Connection FIAT-LI PWR/CAN: Connect provided power/CAN cable MODE: Connect toggle button cable LVDS IR: Connect IR cable R-CAM: Rear camera input QDISPLAY F-CAM: Front camera input T/S OUT: Connect UART 3P cable, Pin #2 (middle) used for touch data transmission... -
Page 5: Dip Switch Setting
DIP Switch Setting * ON : DOWN / OFF : UP Please make sure to disconnect the power cable of the interface and reconnect the power cable again to apply the dip switch changes. FUNCTION Dip S/W SELECT OFF : LVDS IN Mode LVDS ON : LVDS IN Mode Skip OFF : After Market Front Camera... -
Page 6: Remote Control
Remote Control FUNCTION POWER & PIP MENU Activating OSD menu Selection or Mode change ▲ Moving upward ▼ Moving downward Moving leftward ◀ (Press this button 2 seconds long to access the factory mode) Moving rightward ▶ (Press this button 2 seconds long to reset all the data about user environment) * Connect the IR wire with the interface box input “KEY/IR”... -
Page 7: Factory Settings
Factory Settings IMAGE BRIGHTNESS IMAGE Setting for image display PARK CONTRAST FUNC SHARPNESS UTIL INFO PAS TYPE : PAS ON IMAGE PARK PAS SETUP FUNC REAR TYPE : LAMP UTIL RCAM TIME : OFF INFO PARK PAS TYPE: Select parking line type. PAS SETUP: Move the position of parking line. - Page 8 Factory Settings CAR MODEL : RENAULT IMAGE PARK LVDS MODE : SECP-HD FUNC AUTO FCAM : OFF UTIL INFO FUNCTION CAR MODEL: Car Model Settings LVDS MODEL: CARPLAY/Navigation Model Settings SUNE10: QROIX 800x480 setting SE-NAV2 SECP: QDISPLAY 8000x480 update file SECP-D: QDISPLAY 8000x480 update file &...
- Page 9 LVDS Cable / Sub Board Connection Inside Monitor Supplied Sub Board Supplied FFC 30P Supplied Ext. Board Provided LVDS Cable FIAT-LI * Please refer to the next page for the sub board and FFC cable installation inside the monitor.
- Page 10 Sub Board/FFC Cable Installation Please disassemble the monitor and head unit, and find OEM FFC cable in the yellow circle. Smontare il monitor fino alla scheda madre sulla quale è presente il flat cable video originale come indicato in figura. Disconnect OEM FFC cable and insert provided 40P FFC cable like picture.
- Page 11 Sub Board/FFC Cable Installation Connect the other side of 40P FFC cable to supplied sub board like picture. Collegare il flat cable a corredo nell'inserto FROM COMMAND. Connect provided 30P FFC cable to supplied sub board like picture. Connettere il flat cable video 30pin fornito a corredo nell'inserto dedicato rimasto libero 5CH LVDS Reassemble the monitor like picture.
- Page 12 Sub Board/FFC Cable Installation Connect the other side of 30P FFC cable to supplied Ext. board and connect supplied LVDS cable like picture. Collegare l'estremità del flat calbe 30pin nell'inserto dedicato sulla seconda SUB BOARD. Collegare poi il cablaggio LVDS nel suo inserto dedicato.
- Page 13 Control QDISPLAY by Remote Control * Please go to the Factory setting menu and select -> FUNC -> LVDS MODEL: SECP/SECP-HD to use this function. Power button short press: menu confirm Left arrow short press: moving left Right arrow short press: moving right...
- Page 14 Power / CAN Cable Drawing...
- Page 15 RM #404 4TH FLOOR, B-DONG, WOORIMLIONSVALLY, 371-28, GASAN-DONG, GEUMCHEON-GU, SEOUL, KOREA. TEL : 82-2-868-3627~9 | FAX : 82-2-2026-5987...