Table of Contents
Summary of Contents for Kielder KWT-013
- Page 1 18V CORDLESS ANGLE GRINDER TYPE18 ORIGINAL INSTRUCTION MANUAL For use with all variants of KWT-013 Cordless Angle Grinder K I E L D E R 1 8 V B AT T E RY S Y S T E M www.kielder.co...
-
Page 2: Warranty And Support
Why is Registration a Requirement? What is not covered? For Kielder to be able to fully support & service • Kielder does not guarantee the repair or a product warranty over a 3 year period it is replacement of a product incurred as a result imperative that the product is registered. -
Page 3: Intended Use
Tel: 0114 242 3794 Email: tools@kielder.co EN 60745-1 EN 60745-2-3 Intended Use All documentation is held in KWT-013 Technical With the appropriate disc fitted, this tool is File and is available, on request for review. intended for surface preparation and finishing. -
Page 4: General Safety
• If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. KWT-013-IMH22 Kielder WT Ltd... -
Page 5: Battery And Charger
Have your power tool serviced or repaired that may affect the power tool’s operation. by Kielder or a qualified technician using If damaged, have the power tool repaired only identical replacement parts. This will before use. - Page 6 • If necessary, fully secure the workpiece in Any accessories mounted by flanges must a vice or clamp. Never hold a workpiece by fit the locating diameter of the tool’s flange hand. by way of the arbour hole of the accessory. KWT-013-IMH22 Kielder WT Ltd...
- Page 7 A kickback will move the tool in the opposite direction to the wheel’s movement at the point of snagging. Kielder WT Ltd KWT-013-IMH22...
- Page 8 If the wheel is • Do not use other than the Kielder battery binding, investigate and take action to clear packs that are designed for use with this the cause.
- Page 9 Penalties apply incorrect disposal of waste in accordance with national legislation. Kielder WT Ltd KWT-013-IMH22...
-
Page 10: Product Overview
Upper Disc Plate (11) Battery; attached to tool Quick Release Nut (12) Battery Release Button Disc Guard (13) Battery Charge Level Indicator Side Support Handle (14) Charger Trigger (15) Battery Insert Slide Trigger Safety Switch (16) Charge Indicator KWT-013-IMH22 Kielder WT Ltd... -
Page 11: Specifications
Conforms to CE Wear Hearing Protection standard Revolutions Per Minute Do not burn or Wear Safety Glasses incinerate Electrical Capacity Wear Vibration Absorbing Maximum safe ambient Class II construction Gloves temperature for battery (double insulated) MAX 45ºC Kielder WT Ltd KWT-013-IMH22... - Page 12 (E). Note: When fitting a disc, ensure the spindle and disc bore are clean and free from debris. KWT-013-IMH22 Kielder WT Ltd...
- Page 13 (F) and rotate the guard into appropriate position. Replace the cam-lock lever to secure the guard in place. Remove The Battery Pack: Depress the button (G) at the front of the battery indication panel and slide the battery pack out. Kielder WT Ltd KWT-013-IMH22...
-
Page 14: Operating The Tool
If the Spindle Lock engages whilst the tool is operating it could cause catastrophic damage to the machine, with risk of personal injury. Note: Dual function switch can be operated as a trigger or with lock-on. KWT-013-IMH22 Kielder WT Ltd... -
Page 15: Variable Speed
• Do not put strain on the motor as this will activate the overload protection system or could cause permanent damage to the tool. • Use the tool so that the air from the ventilation slots does not blow onto you and thus prevent being burned. Kielder WT Ltd KWT-013-IMH22... -
Page 16: Battery Level Indicator
• The battery level indicator may be used officially assigned location with battery connected or disconnected to the tool. KWT-013-IMH22 Kielder WT Ltd... -
Page 17: Maintenance
Metal objects can make again. If you experience any problems when operating the tool, contact Kielder WT. a connection from one terminal to another and could short the battery terminals... -
Page 18: Charging The Battery Pack
If any dirt is found on the terminals clean the terminals before charging the battery pack. • When the charger is not in use, store in a location to prevent dust or dirt from contaminating the terminals which may cause a fault or short circuit. KWT-013-IMH22 Kielder WT Ltd... - Page 19 • Once charging is complete slide the battery out of the charger, disconnect the charger from power supply and store. Kielder WT Ltd KWT-013-IMH22...
- Page 20 KWT-013-IMH22 Kielder WT Ltd Kielder K I E L D E R W O R K S T E A M Kielder WT Ltd Sheffield, UK T: +44 (0)114 242 3794 E: tools@kielder.co W: http://www.kielder.co Kielder Tools Registered in England & Wales: 09426163...
Need help?
Do you have a question about the KWT-013 and is the answer not in the manual?
Questions and answers