Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for aevit VIC 2.0
- Page 1 AEVIT 2.0 INSTALL-VIC 2.0-042418-REV6 oice nterac tive ontrols INSTALLATION & OperATION MANUAL INSTALLATION BY EMC CERTIFIED TECHNICIAN ONLY! 26 Gabriel Drive • Augusta, ME • Phone: (207) 512-8009 • Fax: (207) 512-8049 • www.aevit.com...
-
Page 2: Table Of Contents
1.3 System Components 2. Wiring 2.1 Standard Wiring Diagram 3. Installation 4. Training 4.1 Important Criteria for Training 4.2 Accessing VIC 2.0 Training Mode 4.3 Training VIC 2.0 5. Operation 6. Final Testing 7. Service Requirements VIC 2.0 INSTALL MANUAL... -
Page 3: Introduction
* These functions are Confirmation Functions (See page 5-1 for more information.) When the activation switch is triggered, VIC 2.0 will first send a signal to AEVIT 2.0 to shut off the ra- dio so it will be quiet. VIC 2.0 will then supply enough power to drive two OEM front speakers so the messages can be clearly heard by the driver. -
Page 4: Wiring
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � VIC 2.0 INSTALL MANUAL... -
Page 5: Installation
INSTALLATION STep 2 EMC requires that VIC 2.0 be secured with at least (2) ¼-20 bolts with lock nuts. EMC also recom- mends that the EMC technician fabricate a mounting plate with (2) ¼-20 studs for VIC 2.0 and weld the mounting plate into the vehicle. - Page 6 Locate the two front speakers and cut the two wires to each speaker so you have a vehicle side (VS) and a speaker side (SS). Strip the wire back approx. 3/8 in, solder and heat shrink the VIC 2.0 speaker...
- Page 7 InstAllAtIon stEP 4B - sInGlE sPEAKER The following diagram shows how to wiring the VIC 2.0 if only one OEM speaker is being used. � � � � � � � � � � � � � � � � � � � � � � � � �...
- Page 8 VIC 2.0 INSTALLATION INSTALLATION STep 5 Connect the Radio Defeat Harness to the VIC 2.0 CPU RD port and route the harness to the vehicle’s radio. All digital radio systems contain two 12VDC power feeds. One of these wires is always “hot” and is used to maintain the radio’s memory.
- Page 9 INSTALLATION STep 7 Connect the 3.5 mm microphone extension cable to the MI port on the VIC 2.0 unit and route the cable to cockpit area of the ve- hicle. The female end of the cable should be mounted in a convenient place so the client can plug it into the microphone.
- Page 10 It is necessary to position the microphone with the client in the vehicle: Typical locations to mount the VIC 2.0 microphone include the “B” pillar or the upper left roof support trim panel that runs between the “A” and “B” pillar.
-
Page 11: Training
See the Operation and Programming Manual for more information. VIC 2.0 has two parts to the training. Part 1, Training, is to record and train the words and Part 2, rec- ognition, is to test the recognition of the words trained during Part 1. -
Page 12: Accessing Vic 2.0 Training Mode
To access the VIC 2.0 Training Mode, follow these steps: STep 1 Wake up the AEVIT 2.0 system and press the “Accept” button on the initial warning screen. If VIC 2.0 is in- stalled properly, VIC 2.0 will say, VIC 2.0: “You now have voice activation”... -
Page 13: Training Vic
Client: “LEFT” TrAININg STep 2 Once Training Part 1 is completed, VIC 2.0 will say: “Training mode part 2.” In this mode, follow the instructions from VIC 2.0 as she will guide you through the recognition portion of the training. -
Page 14: Operation
When training is completed, boot down the AEVIT 2.0 system as described in the Operation and Pro- gramming Manual. Boot up the system by pressing the Wake-Up button and press the Accept Button. VIC 2.0 will say, “You now have voice activation” which means you can now operate the (17) functions listed on page 1-1. - Page 15 The START/STOP Confirmation Functions are a bit different than the shifting functions. In order to START the engine, the client must first physically wake the system up by pressing the “Wake-Up” but- ton. Then, the client can prompt VIC 2.0 to START the vehicle. For example, to START the vehicle: Press the Wake-Up Switch...
- Page 16 Normal operation should be around (3) VI C R ev is io n: 0 2. 03 .0 1 VIC - Volume: This is the volume of VIC 2.0. (1) being the low- est volume and (8) being the highest volume. VIC revision: This is the current software version of VIC 2.0...
-
Page 17: Final Testing
Verify proper operation of all voice commands with client before they take delivery of the vehicle. 7. SerVICe reQUIreMeNTS VIC 2.0 VIC 2.0 does not have any mandatory service requirements. Please contact EMC Service if you have any questions regarding VIC 2.0. VIC 2.0 INSTALL MANUAL...
Need help?
Do you have a question about the VIC 2.0 and is the answer not in the manual?
Questions and answers