Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for MIKO MAH-01W
- Page 1 MYST HUMIDIFIER User Manual MA-04...
- Page 2 READ AND SAVE THESE INSTRUCTIONS AND WARNINGS FAILURE TO COMPLY WITH THE WARNINGS LISTED BELOW MAY RESULT IN ELECTRIC SHOCK OR SERIOUS INJURY. This product should be used only in accordance with the specifications outlined in this manual. Usage other than what has been specified here may result in serious injury.
- Page 3 • DO NOT operate the device if the power plug or power cord is defective. • DO NOT spray flammable materials, e.g. pesticides or fragrances, near the humidifier. • DO NOT place any objects on top of the humidifier, and do not sit or stand on it.
-
Page 4: Product Troubleshooting
PRODUCT TROUBLESHOOTING PLEASE NOTE: IF YOU EXPERIENCE A PROBLEM, DO NOT ATTEMPT TO OPEN THE HOUSING BY YOURSELF. DOING SO MAY VOID YOUR WARRANTY AND CAUSE DAMAGE TO THE HUMIDIFIER OR RESULT IN PERSONAL INJURY. ISSUE CHECKLIST POSSIBLE SOLUTION Whether power is on Press the power button. - Page 5 GET TO KNOW THE MYST Water tank cover Mist Nozzle Handle Water tank Air outlet Aroma drawer Base Air inlet Ultrasonic Filter transducer PTC heater *DO NOT touch the PTC heater to avoid burn. Base Water tank...
-
Page 6: Prior To First Use
PRIOR TO FIRST USE 1. Place the device upright on a solid, level, and water resistant surface. Keep the device away at least 4 inches/10 cm from walls for best results. 2. To ensure optimum performance of the device, please ensure that the mist outlet, air inlet and outlet are not covered. - Page 7 HOW TO OPERATE THE MYST POWER WARM MIST LIGHTING MODES L1- Mood Light L2- Pick a color, Any color L3- Deep Breathing Meditation MIST LEVELS Low / Med / High AUTO Myst monitorsenvironment humidity and maintains it to a perfect 60%. SLEEP Long press (2s) to enter sleep mode.
- Page 8 HOW TO OPERATE THE MYST BY REMOTE CONTROLLER Same as the Power button on unit Same as the WARM button on unit AUTO Mode: ON / OFF Same as the Mist Level button on unit Same as the Timer Sleep Mode: ON / OFF button on unit Switch between Light Mode of RGB Random / Set Color / OFF...
- Page 9 HOW TO CLEAN THE MYST ATTENTION! ALWAYS POWER OFF AND UNPLUG THE DEVICE BEFORE CLEANING THE DEVICE. WIPE THE SURFACE OF THE DEVICE WITH A SOFT AND DAMP CLOTH IF NEEDED. Water tank Remove the water tank cover, empty the water tank. Use water, vinegar solution or dish soap to wash the inside of the water tank.
-
Page 10: Transport And Storage
HOW TO DESCALE Depending on usage and water quality, cleaning to remove scale may be required weekly or every other week to optimize performance. If you live in a hard water area, distilled water is recommended to be used on this device. This will help reduce the precipitation of minerals or ‘white dust’. -
Page 11: Technical Data
TECHNICAL DATA Model number: MAH-01W Humidification mode: Miko MYST Top Filling Ultrasonic Warm/Cool Mist Power supply: 120V~, 60Hz Power consumption: 30W(cool mist), 90W(warm mist) Tank capacity: 4.5L Mist output: 300ml/h(cool mist), 400ml/h(warm mist) Dimensions: 195*195*319mm/ 7.7*7.7*12.6 in CORRECT DISPOSAL OF THIS PRODUCT Please dispose of this product after its service life pursuant to the Waste Electrical and Electronic Equipment Directive 2012/19/EU- WEEE.
Need help?
Do you have a question about the MAH-01W and is the answer not in the manual?
Questions and answers
Flashing E 1 light. Also, the unit never shuts off when empty.
A flashing E1 light on the MIKO MAH-01W indicates that there is no water in the water tank or the water tank is not properly placed. When this happens, the device stops producing mist automatically, but the fan continues to run.
This answer is automatically generated
Hi my Miko humidifier stopped working
Your MIKO MAH-01W humidifier may have stopped working due to several possible reasons:
1. Power Issues – Ensure the power plug and cord are not defective and that the device is properly plugged into a working outlet.
2. Water Level – Check if the water tank is empty or improperly placed. The humidifier may not operate without sufficient water.
3. Blocked Filter – A clogged filter inside the water tank may restrict water flow. Clean it as instructed.
4. Mineral Deposits – Mineral buildup inside the device could block mist output. Clean the water tank, filter, and base with water, vinegar solution, or dish soap.
5. Safety Features – The device may have automatically shut off due to overheating or tilting. Ensure it is on a stable surface and restart it.
6. Defective Components – If the unit still does not work, internal electrical or mechanical issues may require professional servicing. Do not attempt repairs yourself, as this voids the warranty.
Try these steps to troubleshoot the issue. If the problem persists, contact qualified personnel for servicing.
This answer is automatically generated
Mist is being produced...but not coming up the top of the column to the outside.
The mist from the MIKO MAH-01W may not be coming up the top of the column due to the following reasons:
1. Ultrasonic Transducer Blockage – The ultrasonic transducer may be covered by white dust, scale, or other objects. Cleaning the transducer or removing any obstructions can resolve the issue.
2. Low Water Level or Incorrect Tank Attachment – The water tank may be empty or not correctly attached to the base. Refilling the tank and ensuring proper attachment can help.
3. Hard Water Usage – If hard water is used, mineral buildup may affect mist production. Using distilled water is recommended.
4. Device Not on a Level Surface – The device may not be placed on a level surface, affecting mist output. Placing it on a stable, level surface can fix this.
Checking and addressing these issues should restore normal mist production.
This answer is automatically generated
The mist button is blinking. What does that mean?