Advertisement
DISCLAIMER
Under no circumstances will AOTO be liable for direct or indirect economic losses to customers due to this product
manual, and AOTO's maximum compensation for customer losses due to AOTO's liability shall not be higher than the
amount paid by customers for purchasing the product / service.
Outsourced parts are not included in the scope of service covered by this service manual.
AOTO may improve or update product versions or programs. Product details are subject to the actual shipping
SID Stand-alone LED Display
version, and the user manual will be updated without notice. This version may contain translation or typographical
errors, and any changes will be updated and published on the latest version.
User Manual
Copyright 1993-2020 Shenzhen AOTO Electronics Co., Ltd. All rights reserved. Global patent pending. AOTO and CLD are
trademarks of Shenzhen AOTO Electronics Co., Ltd. Specifications are subject to change without notice.
* Please read the manual thoroughly and save it before attempting to connect,
operate or adjust the product.
w w w . a o t o . c o m
Advertisement
Summary of Contents for AOTO SID303SD
- Page 1 DISCLAIMER Under no circumstances will AOTO be liable for direct or indirect economic losses to customers due to this product manual, and AOTO's maximum compensation for customer losses due to AOTO's liability shall not be higher than the amount paid by customers for purchasing the product / service.
-
Page 2: Table Of Contents
Contents product introduction··················································03 Installation Guide···························································05 Function introduction················································06 Maintenance ···································································15 Troubleshooting······························································18 Transportation and delivery·······························19... - Page 3 Copyright>> 15)Arrange professionals to inspect the display regularly. Shenzhen AOTO Electronics Co., Ltd. reserves the right to change this Manual, which has no further notice for Safety Regulations>> subsequent changes, and shall not be responsible for any direct, indirect, intentional, or unintentional damage and/or hidden danger caused by improper installation or use of the product without following the manual.
-
Page 4: Product Introduction
Product introduction Description Remarks Frame Installing the display panel Product appearance: Border Display protection of SID stand-alone display Power input Power supply to SID stand-alone display Lower beam Control unit of SID stand-alone display Back socket Signal input/output A-type base Support structure of SID stand-alone display Castor Moving parts of SID stand-alone display... -
Page 5: Installation Guide
Precautions: Model H1(mm) H2(mm) W1(mm) W2(mm) W3(mm) L(mm) SID303SD / SID303SI / SID503SD SID303SD / SID303SI / SID503SD 2678 1645.5 2259 19.8 1．After the product is unpacked, please check whether the product is damaged; / SID503SI / SID703SD / SID703SI / SID503SI / SID703SD / SID703SI 2．At least two people are required to participate in the installation process to ensure safety;... - Page 6 Software: Interface Features USB Control out interface can be used to connect computers and other 1)Use the remote control or press POWER_KEY for startup; After entering the main menu of the SID Stand-alone LED Interface 1 devices to realize Sid stand-alone LED display anti control device Display software, the following functions can be selected according to the actual needs: Whiteboard, signal source Interface 2 SPDIF OUT interface，are used to connect the sound and other equipment...
- Page 7 3)Select the projection function to select the transmitter projection, computer-software projection and mobile Display setting projection; follow the instructions in the figure below to realize the projection; “display setting” application,which able to be adjusted the brightness/ contrast ratio/ saturation/ color temperature of the LED display by manual or automatic operation.
- Page 8 OtaService Sound pick-up 1)In the application of "OtaService", SID stand-alone LED display can be upgraded with local USB. 1) Insert the USB signal receiver of the pickup into the USB2.0/USB3.0 interface of the lower beam of the SID stand-alone LED display, and press the power button of the pickup to open the device; 2) Open the Tencent conference and log in;...
- Page 9 Welcome screen 2)Insert the transmitter into the USB interface of the computer, and the dialog box below will pop up automatically; after the flashing arrow appears in the dialog box, you can press the Transmitter button for one-key projection. In With a variety of theme templates, you can edit the background, add text, change the text position, size, color and particular, if it is the first time to use the transmitter in a computer, you need to manually double-click the execut- so on.
-
Page 10: Maintenance
The main process of front display maintenance is as follows: Maintenance Step 1: Turn off the power of the display; Step 2: Place the tool on the surface of the module after connected it to the AC power cord , press the switch and the mark "I"... -
Page 11: Troubleshooting
Cleaning: Troubleshooting During the use of the product, dust or other stains may adhere to the surface of the cabinet, affecting the effect of the display, so the display needs to be cleaned regularly to ensure that it is in the best effect. Failure Analysis Solutions... -
Page 12: Transportation And Delivery
3．AOTO is not responsible for any personal, property or other damages caused by the failure of contents below of this document, including but not limited to instructions, steps, specifications, warnings, etc.
Need help?
Do you have a question about the SID303SD and is the answer not in the manual?
Questions and answers