Related Manuals for Kielder KWT-011
Summary of Contents for Kielder KWT-011
- Page 1 KWT-011 TYPE18 ORIGINAL INSTRUCTION MANUAL For use with all variants of KWT-011 Drill Driver K I E L D E R 1 8 V B AT T E RY S Y S T E M www.kielder.co KWT-011-IMA21...
- Page 3 EN 60745-2-2:2010 0114 242 3794 EN 55014-1:2006+A1:2009+A2:2011 Email: tools@kielder.co EN 55014-2:1997+A1:2001+A2:2008 All documentation is held in KWT-011 Technical Intended Use File and is available, on request for review. This tool can be used to tighten screws in Authorised Signatory: screw mode, drill holes in wood & metal in Steven Bulloss drill mode.
- Page 4 • If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. KWT-011-IMA21 Kielder WT Ltd...
- Page 5 If damaged, have the power tool repaired Have your power tool serviced or repaired before use. Many accidents are caused by by Kielder or a qualified technician using poorly maintained power tools. only identical replacement parts. This • Keep cutting tools sharp and clean.
- Page 6 ‘live’ wire will make exposed metal parts of the tool ‘live’ and shock the operator. • Be aware that this tool is always in an operating condition as it does not have to be plugged into an electrical socket. KWT-011-IMA21 Kielder WT Ltd...
- Page 7 Li-Ion • Do not use other than the Kielder For proper treatment, recovery and recycling battery packs that are designed for use of old products and used batteries, please with this rechargeable tool.
- Page 8 Torque Selection Ring (11) Battery Charge Level Indicator Speed Selection Switch (12) Battery Release Button Forward / Reverse / Lock Selector (13) Charger Trigger (14) Battery Insert Slide Hand Grip (15) Charge Indicator Belt Clip Fitting KWT-011-IMA21 Kielder WT Ltd...
- Page 9 (double insulated) Volts Wear Hearing Protection Conforms to CE standard Direct Current Wear Safety Glasses Do not burn or incinerate Revolutions Per Minute Indoor Use Only Maximum safe ambient Electrical Capacity temperature for battery MAX 45ºC Kielder WT Ltd KWT-011-IMA21...
- Page 10 Depress the button (F) at the front of the battery indication panel and slide the battery pack out. Removing a Drill or Driver Bit Turn the lock collar (C) anticlockwise (looking from the front) then remove the bit (A). KWT-011-IMA21 Kielder WT Ltd...
- Page 11 When drilling allow the bit to do the work. Ensure that the tool is used in such a way as to prevent the hot air from the vent holes being blown onto your skin as this may cause burns. Kielder WT Ltd KWT-011-IMA21...
- Page 12 When selecting a different speed it maybe necessary to run the motor slowly, by partially depressing the trigger for the gears to properly align. Once the motor is slowly running apply pressure to the speed selector switch and the gear will engage. KWT-011-IMA21 Kielder WT Ltd...
- Page 13 Charge Red light illuminated = Low Charge/Empty If the battery is of low charge, it should be charged before further use. The battery level indicator may be used with battery connected or disconnected to the tool. Kielder WT Ltd KWT-011-IMA21...
- Page 14 • When the battery pack is removed from the main unit, store the battery in a location to prevent dust or dirt from contaminating the battery terminals which may cause a short circuit. KWT-011-IMA21 Kielder WT Ltd...
- Page 15 If any dirt is found on the terminals always allow the battery pack to cool down clean the terminals before charging the before recharging. This will allow the battery battery pack. to be recharged to its full capacity. Kielder WT Ltd KWT-011-IMA21...
- Page 16 Why is Registration a Requirement? importer or retailer for that country. For Kielder to be able to fully support & What is not covered? service a product warranty over a 3 year • Kielder does not guarantee the repair...
- Page 17 Notes [10x10mm] Kielder WT Ltd KWT-011-IMA21...
- Page 18 Notes [10x10mm] KWT-011-IMA21 Kielder WT Ltd...
- Page 20 KWT-011-IMA21 Kielder WT Ltd Kielder K I E L D E R W O R K S T E A M Kielder WT Ltd Sheffield, UK T: +44 (0)114 242 3794 E: tools@kielder.co W: http://www.kielder.co Kielder Tools Registered in England & Wales: 09426163...
Need help?
Do you have a question about the KWT-011 and is the answer not in the manual?
Questions and answers