4G Lift Dialer & 4G Lift Dialer Box Preface All rights reserved; no part of this publication may be reproduced, stored in a retrieval system, or trasmitted in any form or by any means, electronic, otherwise, without the prior written permission of Digicom S.r.l. The contents of this booklet may be modified without notice. Every possible care has been taken in testing and putting together all the documentation contained in this booklet, however Digicom can not take any responsability brought by the use of this booklet.
4G Lift Dialer & 4G Lift Dialer Box Preface SAFETY WARNINGS Read these instructions and norms carefully before powering the device. Violation of such norms may be illegal and cause hazard situations. For any of the described situations please refer to the specific instructions and norms. The device is a low power radio transmitter and receiver.
4G Lift Dialer & 4G Lift Dialer Box Introduction 1. INTRODUCTION Thanks for purchasing a Digicom product! 4G Lift Dialer and Voice Box constitute a bidirectional Emergency phone for lifts system, compliant to EN 81-28, EN 81-20, EN 81-70 regulations. The Emergency phone allows the users blocked in a lift cabin to send an alarm via GSM to a Service Center or to the authorized Technical people.
4G Lift Dialer & 4G Lift Dialer Box Introduction 1.2. SYSTEM DESCRIPTION AND PACKAGE CONTENT Digicom Emergency phone for lift system is composed by two main elements: 4G Lift Dialer Remote alarm dialer with native integrated 4G/LTE module. Voice Box Speakerphone unit with integrated microphone and speaker.
Page 9
4G Lift Dialer & 4G Lift Dialer Box Introduction Voice Box speakerphone unit, only 19mm thick and powered directly by 4G Lift Dialer Emergency phone, is available in the following versions: Voice Box Car (cod. 8D5804) For the installation in car behind the car operating panel. Equipped with: •...
4G Lift Dialer & 4G Lift Dialer Box Installation 2. INSTALLATION Here below the procedure for the installation and configuration of 4G Lift Dialer and Voice Box together. This user's manual can be used for the following models of 4G Lift Dialer: •...
4G Lift Dialer & 4G Lift Dialer Box Installation 2.3. TESTS DURING THE INSTALLATION Locate a proper position for the various parts of the system and before the final mounting check the following: • 4G Lift Dialer Emergency phone • SIM correctly inserted; •...
4G Lift Dialer & 4G Lift Dialer Box Installation 2.4. BEFORE POWERING LIFT DIALER ON Place 4G Lift Dialer where you prefer, in a zone with a good GSM signal, and go on as follows: 1. Open the SIM holder by slightly pressing and pushing it horizontally toward the internal side of the card.
4G Lift Dialer & 4G Lift Dialer Box Installation 2.5. VOICE BOX CONNECTION Place the Voice Box(es) where you prefer and go on as follows: 1. Switch Off the 4G Lift Dialer. 2. Connect pins 5-6 of 4G Lift Dialer to pins 1-2 of Voice Box. PINS CAN BE CROSSED.
4G Lift Dialer & 4G Lift Dialer Box Installation 2.6. 4G LIFT DIALER PINOUT DESCRIPTION NOT USED NOT USED PHONE PHONE VOICE BOX VOICE BOX IN F (ALARM FILTER) IN SOS IN T (TECHNICAL ALARM) GND (IN F , IN SOS , IN T) RELAY1 - N.O.
4G Lift Dialer & 4G Lift Dialer Box Installation 2.10. VOICE BOX - TOP / PIT PINOUT (CODE 8D5780) DESCRIPTION LIFT DIALER LIFT DIALER NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED For a good audio quality we suggest the use of a twisted pair for the connection. Otherwise it is possible: - to use two unused wires already present in the cabin cable;...
4G Lift Dialer & 4G Lift Dialer Box Installation 2.12. VOICE BOX BUTTON PINOUT (CODE 8D5810) DESCRIPTION NOT USED NOT USED NOT USED VOICE BOX CAR NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED VOICE BOX CAR NOT USED For installation on Top/Pit, with alarm button only, without integrated microphone and speaker.
4G Lift Dialer & 4G Lift Dialer Box Installation 2.14. LIFT DIALER: LED INDICATORS ANTENNA Through 3 led indicators you can check the status of 4G Lift Dialer: SERIAL PORT RS232 STATUS DESCRIPTION RESET 1 POWER Device powered OFF USB PORT Blinking Main power absent, battery in use RS232 ENABLED...
ANTENNA 4G Lift Dialer & 4G Lift Dialer Box Installation SERIAL PORT RS232 2.16. BACKUP BATTERY RESET USB PORT 4G Lift Dialer can be equipped with a backup battery (Digicom code 724000163401) to ensure proper operation in the event of RS232 ENABLED main power blackout.
4G Lift Dialer & 4G Lift Dialer Box Configuration CONFIGURATION 4G Lift Dialer can be configured with: • Lift Manager Application for Android smartphones via SMS or BLE; • SMS with mobile phone; • phone or mobile phone calling the Emergency phone; •...
4G Lift Dialer & 4G Lift Dialer Box Configuration 3.3. CONFIGURATION VIA SMS Send to the SIM phone number of 4G Lift Dialer the SMS messages as reported in the CONFIGURATION TABLE. The message must be always precedeed by the access Password. With the configuration via SMS it is possible to send to 4G Lift Dialer several commands with a sole SMS, by inserting at the beginning of the message the Access password once only.
Page 27
4G Lift Dialer & 4G Lift Dialer Box Configuration DESCRIPTION COMMAND Alarm call (ex. Pit or smoke flooding sensor): Phone Number 23 [xx] * [pp] * [numero tel] # (sensor connected to VoiceBox) xx : phone book position from 01 to 12 Es.
Page 28
4G Lift Dialer & 4G Lift Dialer Box Configuration DESCRIPTION COMMAND Alarm Call: delay for the recall in case of disconnection of the line without 3 9 0 [mm] # alarm reset (19) mm: minutes from 00 to 59 (default 02) In case of missed call, the next attempt is made after 20 seconds.
Page 29
4G Lift Dialer & 4G Lift Dialer Box Configuration DESCRIPTION COMMAND Alarm reset by configuration 1 9 # Alarm reset during speakerphone on Enable the answer to configuration messages via SMS. 9 4 [r] # By enabling the answer, after the configuration message, you will receive ACK 0 answer disabled (default 0) if the command is correct and it has been executed, NACK if the command 1 answer enabled...
Page 30
4G Lift Dialer & 4G Lift Dialer Box Configuration DESCRIPTION COMMAND Relay1 management: open gate 8 1 # N.O. pin12-13 N.C. pin13-14 If the bell management is active (command 84t#) the command open gate 81# is ignored. Relay1 management: bell management 8 4 [t] # t: 0 = disabled (default 0).
Page 31
4G Lift Dialer & 4G Lift Dialer Box Configuration DESCRIPTION COMMAND PUK insertion and new PIN * 9 3 [puk] * [pin] # puk: puk code of the SIM, 10 digits. After 10 faulty attempts, the SIM is disabled. Contact the telecom operator.
4G Lift Dialer & 4G Lift Dialer Box Configuration 3.5. CONFIGURATION EXAMPLES Phone number for SOS calls: 3351111111 (see line 3) Second phone number for SOS calls: 3352222222 (see line 4) Phone number for Autotest calls: 3408888888 (see line 5) Periodic test call every 3 days at a time calculated by 4G Lift Dialer (see line 6) Current date and time: 3 June 2014, time 16:04...
4G Lift Dialer & 4G Lift Dialer Box Configuration 3.9. MANAGING THE ALARM CALL When the Alarm Center and/or Support service receive the alarm call, while listening the message, they can perform the following operations: • press a configured key to playback the alarm message again; the digit code can be modified with command 95*04*[d]# (in factory settings, none key is configured, and the emergency phone repeats the message 10 times).
4G Lift Dialer & 4G Lift Dialer Box Configuration 3.13. CHANGING THE LANGUAGE (COMMAND 45*XX#) To select language of standard messages: comfort, alarm, welcome. • 45*39# Italian (default) • 45*34# Spanish • 45*44# English • 45*31# Dutch • 45*49# German •...
4G Lift Dialer & 4G Lift Dialer Box Configuration 3.16. ACTIVATING THE INTERCOM FUNCTION (COMMAND *1) The intercom function between the lift Car and the Control Center or the concierge service can be activated with a common phone connected to pin 3-4 of the Emergency phone. To activate the conversation with the people in the Car: •...
4G Lift Dialer & 4G Lift Dialer Box Configuration 3.18. RELAY1: BELL MANAGEMENT (COMMAND 84T#) For the connection between 4G Lift Dialer and VoiceBox Car you can use the 2 wires already present and normally used for the bell. Here below the installation procedure to be carried on with 4G Lift Dialer powered off. In the machine room, looks for the 2 wires going to the bell and connect them to Relay1 N.O.
4G Lift Dialer & 4G Lift Dialer Box Configuration 3.21. RELAY 1 AND RELAY 2: SENT ALARM AND RECEIVED ALARM (COMMAND 851#) It is possible to report to the signals "Alarm Sent" and "Received Alarm", respectively on Relay 1 and Relay 2 of the 4G Lift Dialer, with command 851 # From this moment on, when the yellow Alarm Alarm LED turns on or off on the VoiceBox, the Relay 1 changes state;...