Related Manuals for TELEFLY TELE2210G-2GF-8GT
Summary of Contents for TELEFLY TELE2210G-2GF-8GT
- Page 1 TELE2210G-2GF-8GT Full Gigabit Din-rail mount Industrial Ethernet Switch User Manual Edition: V1.0) TELEFLY TELECOMMUNICATIONS EQUIPMENT CO.,LTE www.telefly.cn...
- Page 2 TELE2210G-2GF-8GT Full Gigabit Din-rail mount Industrial Ethernet Switch Safe Use Instruction This product performance is excellent and reliable in the designed range of use, but it’s necessary to avoid man-made damage or destroy for the equipment. Read the manual carefully and keep this manual for reference if need afterwards.
-
Page 3: Table Of Contents
TELE2210G-2GF-8GT Full Gigabit Din-rail mount Industrial Ethernet Switch Catalogue 1. System outline............- 1 - 1.1. Product Introduction..............- 1 - 1.2. Product Characteristic..............- 1 - 1.2.1. Industrial network features..............- 1 - 1.2.2. Industrial-grade power supply design..........- 1 - 1.2.3. -
Page 4: System Outline
TELE2210G-2GF-8GT Full Gigabit Din-rail mount Industrial Ethernet Switch 1. System outline 1.1. Product Introduction The TELE2210G-2GF-8GT is a high performance unmanaged industrial Ethernet switch with total 10 Gigabit Ethernet ports. It has 2x1000Base-X SFP fiber ports and 8x10/100/1000Base-T RJ45 ports, which is suitable for the big bandwidth Ethernet communications. -
Page 5: List
User manual Certificate and warranty card 1.4. Product election The TELE2210G-2GF-8GT switch provides two types of AC and DC products for customers to choose. The product model list is shown in Table 1-2. Table 1-2 TELE2210G-2GF-8GT switch product model list... -
Page 6: Technical Index
TELE2210G-2GF-8GT Full Gigabit Din-rail mount Industrial Ethernet Switch 2. Technical Index Content TELE2210G-2GF-8GT 2x1000Base-X SFP socket Ports quantity 8x10Base-T/100Base-TX/1000/Base-T RJ45 port Standard support: IEEE802.3,IEEE802.3u, IEEE802.3ab,IEEE802.3x System parameter MAC address table:4K Switch method: storage and forward GF:1000Base-X Wavelength: 1310nm or 1550nm (Single mode);... -
Page 7: Hardware Installation And Testing
3. Hardware installation and testing 3.1. Hardware structure 3.1.1. Product configuration The TELE2210G-2GF-8GT uses Din rail mount installation and whole machine with six sides fully enclosed structure.The dimensions(not including DIN rail size) are: 136mm×54mm×110mm (height×width×depth). 3.1.2. Front panel and side panel... -
Page 8: Power Supply
Side panel of DC/AC model 3.2. Power supply The DC power supply model of the TELE2210G-2GF-8GT switch supports DC12~48V power supply, dual power input, and the two power supplies are mutually backup. Use 5-ways lockable 5.08mm pitch terminal, as shown in the figure below: The TELE2210G-2GF-8GT has a 3-ways lockable 5.08mm pitch terminal... -
Page 9: Led Indicator Lights
TELE2210G-2GF-8GT Full Gigabit Din-rail mount Industrial Ethernet Switch When the switch works well, the normally open relay is closed,and the normally closed relay is off.When the device power off, the normally open relay is off,and the normally closed relay is closed. Recommended load capacity of the relay switch is 1A (24VDC).The user can connect other sound and light... -
Page 10: Cable Connection
TELE2210G-2GF-8GT Full Gigabit Din-rail mount Industrial Ethernet Switch the installation of the switch. Checking if there was suitable power supply for the switch. Please select the correct position for the switch. Install switch on DIN-RAIL as following steps: Insert the upper part of the DIN rail into the slot on the upper part of the DIN rail connection base with the circlip. - Page 11 TELE2210G-2GF-8GT Full Gigabit Din-rail mount Industrial Ethernet Switch Hot-pluggable SFP modules as follows: Hot-plug procedure: Observe the end with PCB gold finger during SFP Insert the golden finger end into the metal shielding cage of the SFP, and hear a clicking sound to indicate that the device has been inserted in place, and then put the SFP plug-in handle on the normal position parallel to the interface.Then it means we can use it.
-
Page 12: Simple Test
TELE2210G-2GF-8GT Full Gigabit Din-rail mount Industrial Ethernet Switch performance Connect one end of the optical cable to the optical interface, and the other end to the optical interface of another device After connection is completed, check the corresponding LINK/ACT indicator of the fiber port on the front panel. If the indicator is on, the connection is valid. - Page 13 TELE2210G-2GF-8GT Full Gigabit Din-rail mount Industrial Ethernet Switch is a schematic diagram of the optical port test in the TELE2210G-2GF-8GT switch. Figure 3-8 Schematic diagram of optical port test www.telefly.cn - 10 -...
-
Page 14: Maintain And Service
TELE2210G-2GF-8GT Full Gigabit Din-rail mount Industrial Ethernet Switch 4. Maintain and service The switch has 5 years’ guarantee according to the product specifications of Maiwe, we will maintain or replace the product for free if has any problem during the guarantee.However, the above commitment does not cover damage caused by improper use, accidents, natural disasters, incorrect operation or incorrect installation.
Need help?
Do you have a question about the TELE2210G-2GF-8GT and is the answer not in the manual?
Questions and answers