Related Manuals for LOCKLY GUARD DUO 679D
Summary of Contents for LOCKLY GUARD DUO 679D
- Page 1 WWW.LOCKLYPRO.COM PGD679DW FOR COMMERCIAL USE & PROFESSIONAL INSTALLATION DUO (679D) INTERCONNECTED EDITION INSTALLATION GUIDE...
- Page 2 GET THE MOST OUT OF YOUR LOCKLY GUARD ™ Get the latest user/installation manuals , instructional videos, and FAQs SCAN or VISIT Locklypro.com/679D...
- Page 3 Welcome! This guide will walk you through step-by-step how to install and get Lockly Guard up and running. Instal- ™ lation generally takes less than 30 minutes. If you have any questions please call our VIP Hotline (855) 562-5599 for help.
- Page 4 Preparation To complete the installation you will need: Flathead Screwdriver Tape measure or ruler Phillips Screwdriver Optional Screwdriver with drill bits Pliers Drilling maybe required to install this lock. If you are installing your lock on a brand new door, a drill is required if there are no holes prepared for lock installation. Use provided template to bore holes on door.
-
Page 5: Important Notice
Preparation Remove existing door hardware, latch or deadbolts before installing the new lock. Use provided template to bore new holes if needed. Measure and confirm your door is 1- 3/8"—2" (35mm—50mm) between 1-3/8" - 2" ( 35mm - 50mm). 2-1/8" 54mm 1"... - Page 6 Step 1 INSTALLING THE LOCKSET Measure the distance between center of front door hole to the edge of your door hole to determine the backset. Adjust latchbolt and deadbolt according to the backset of your door. Deadbolt Adjustment 2-3/8"(60mm) 2-3/4"(70mm) extend I.
- Page 7 Step 1 INSTALLING THE LOCKSET continued After adjusting the latchbolt , determine the orientation of the latchbolt. Determine the orientation of latchbolt. Facing the door exterior, install the latchbolt according to the opening direction of your door. LEFT OUT-SWING DOOR RIGHT OUT-SWING DOOR Inside Inside...
- Page 8 Step 2 CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS The lock ships with handle default for right in-swing or left out-swing door. Check the diagram below if you are unsure of you door orientation. RIGHT IN-SWING DOOR INTERIOR LEFT IN-SWING DOOR Hinge Side LEFT OUT-SWING DOOR...
- Page 9 Step 2 CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS continued Rotate the handle 180° to the other side Confirm that your installation was complete by of the lock. checking if the pins are flush against the handle, and has popped out. Adjust the handle accord- Using your fingers, press the two pins located ingly to make sure the pins are fully decom- on the left and right side of the the lock...
- Page 10 Step 2 CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS continued At the back of the exterior panel, remove the screw on point "R". Align the screw hole on point "L" then insert the removed screw and tighten.
- Page 11 Step 2 CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS continued Changing the Interior Handle Orientation Remove the handle retaining screw. Rotate the handle to 180° as shown. Insert the handle retaining screw to the left screw hole and tighten.
- Page 12 Step 3 PREPARING LOCK FOR INSTALLATION Carefully prepare the lock and ensure the required parts ( ) have been properly attached before installing to door. Peel paper layer OFF the Adhesive tape and prepare for installation. Carefully bend the end Install Spindle C with of the locking pin D with the holes side into the...
- Page 13 Step 4 INSTALLING EXTERIOR SIDE OF LOCK Exterior Press the door to open the hole, Note: select E to fit in 4" or 5.5" positio While aligning the lock straight up-and-down, pass the wiring cable under the latchbolt then ensure the Slotted Exterior Barrel Extension passes through the hole on the lower...
- Page 14 Step 5 INSTALLING INTERIOR SIDE OF LOCK Select interior cover plate according to door hole distance and install on to door. 4” use cover plate 5.5” use cover plate Ensure the rods on interior cover plate is inserted on the holes of the deadbolt. and the cable and spindle passed through part .
- Page 15 Step 5 INSTALLING INTERIOR SIDE OF LOCK continued Secure interior cover plate with screws , then remove the positioning tool Check and ensure the spindle is at the center after removing Hole for screw for 5.5" Hole for screw for 4" Check and ensure the spindle is at the center after removing...
- Page 16 Step 5 INSTALLING INTERIOR SIDE OF LOCK continued according to door handle orientation Left Select the side of the interconnection gear or Right . Insert torque blade to plate according the distance between the latchbolt and deadbolt . Select the correct side of the interconnection gear. For right swing door For left swing door Insert...
- Page 17 Step 5 INSTALLING INTERIOR SIDE OF LOCK continued Install plate onto door. Ensure the torque blade is inserted horizontally to the deadbolt. The spindle must pass through the plate. Secure the plate with screws...
- Page 18 Step 6 INSTALLING THE LOCK INTERIOR (N) Make sure the cable is away and not tangling with the spindle Secure the lock interior with 3 screws Plug the cable into the interior side of the lock Align the spindle to the lock interior making sure you match the orientation of the and attach the Interior lock to the Interior plug by matching the red side on the plug with...
- Page 19 Step 6 INSTALLING INTERIOR SIDE OF LOCK continued Insert 4 AA batteries into the lock by aligning the positive (+) and negative (-) orientation markings on the batteries to the battery chamber. Secure the battery by sliding the cover over the lock and turning the screw clockwise on top until tight.
- Page 20 Door sensors provide real-time door condition status, such as the ability to verify if the door is securely closed. It also sends push notifications to your phone whenever your door opens and enables voice control. Lockly Guard Duo (679D) comes with a pre-wired door sensors consisting of two parts: ™...
- Page 21 Step 7 PREPARING DOOR SENSORS FOR INSTALLATION continued When you are installing the door sensors, make sure the arrow of the wired sensor is placed next to the arrow of the sensor magnet close as possible. IMPORTANT: Do not install the sensor LEFT close to the strike plate RIGHT...
- Page 22 Step 7 PREPARING DOOR SENSORS FOR INSTALLATION continued The interior assembly comes with the For left swing doors, re-route the door sensor pre-installed wired door sensor setup wire through the side channel. Trim excess for a right swing doors with 2-3/4" part for doors with 2-3/8"...
- Page 23 Step 8 INSTALLING THE DOOR STRIKE It is recommended that you use the included strike plate. However, if you find the deadbolt and latchbolt works with your existing strike plate free of any binding or resistance you can use it. Regardless of which strike plate used, deadbolt and latchbolt needs to operate smoothly, free of any binding or resistance.
- Page 24 Step 9 INSTALLING THE DOORS SENSOR Make sure you have prepared the door sensors for installation according to Step 7 Position the wired sensor to the edge Peel off the paper layer of the of the door, avoiding the door strike plate. adhesives from the back of the Attach and secure with the adhesives.
- Page 25 Step 10 DOWNLOAD LOCKLY APP Congratulations! You have completed the Lockly Guard™ Duo (679D) physical lock installation. To complete your setup, download the Lockly app from the iOS or Google Play app Store and follow on-screen instructions. Scan or visit Locklypro.com/app...
- Page 26 Step 11 SETTING UP THE SECURE LINK WI-FI HUB To set up your Lockly Guard™ Duo (679D), choose an appropriate location for the Secure Link Wi-fi Hub for optimum performance (see below). For optimum connectivity, it is recommended that the hub be no further away from the lock than 30 feet (9 meters).
- Page 27 Step 11 SECURE LINK WI-FI HUB SETUP continued Plug the Secure Link Wi-Fi Hub into the 5V 1A USB AC adapter and plug the AC adapter to your wall socket. GREEN LED indicator light will flash slowly to indicate that the Wi-Fi Hub is ready to connect.
- Page 28 Step 12 CONNECTING YOUR LOCKLY GUARD™ DUO (679D) The App will take you through the following steps, make sure the smart lock has been properly installed. You will need your activation card that is included in the box to proceed.
- Page 29 Step 12 CONNECTING YOUR LOCKLY GUARD™ DUO (679D) continued Plug in your Secure Link Password setting OK and Click "YES" Confirm lock password Set the Admin Code 9:46 AM 100% 9:45 AM 100% ●●●●● AT&T ●●●●● AT&T 9:45 AM 100% ●●●●●...
- Page 30 FCC Warning： This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Page 31 This lock can be installed for both right swing and left swing doors. The lock ships ready for a right swing door installation. INSTALLATION OVERVIEW & PARTS LIST If you wish to change the orientation of the lock for a Left Swing door, go to Step 2 (Installation Guide) for instructions. Battery Cover 2-3/4"...
-
Page 32: Important Notes
WAIT. IMPORTANT NOTES Lockly installs differently from other door locks. Professional installer(s) and locksmiths must read and follow Lockly installation and user manuals to prevent damaging the product. Failure to do so may also result in the smart lock not responding correctly to lock and unlocking commands and will require re-installation. - Page 33 FOR COMMERCIAL USE & PROFESSIONAL INSTALLATION We’re here to help! prosales@lockly.com locklypro.com/support © Copyright 2022 Lockly All rights reserved USA Patent NO. US 9,881,146 B2 | USA Patent NO. US 9,853,815 B2 | USA Patent NO. US 9,875,350 B2 | USA Patent NO. US 9,665,706 B2 | USA Patent NO. US 11,010,463 B2 | AU Patent NO.