MHGOALS FT-342 Installation Manual

Folding goals

Advertisement

Quick Links

1
2

Installation of Goals

A
Always use the instructions and recommendations provided by the manufacturer when installing
equipment
The appropriate personal protective equipment (PPE) must be worn at all times. I.E. Hard hat, steel
toe cap boots, gloves, etc.
B
When tall and/or heavy equipment is being assembled, it is recommended that scaffolding and/or
heavy lifting equipment is used.
A risk assessment should be carried out if necessary.
Installation should only be undertaken by, or under the direct supervision of, trained persons with
enough experience and with the adequate assistance for the size of the goal being assembled.
C
For spares or assistance please get in contact with MH GOALS Via -
T
- 01502 711 298
E
- Info@mhgoals.com
D
W
- www.mhgoals.com
E
F
G
H
1
2
3
4
5
3
4
5
6
7
8
6
7
8
9
10
11
9
10
11
12
A
B
C
D
E
F
G
MH Goals Ltd,
Ellough Industrial Estate,
H
Beccles, Suffolk,
NR34 7TD
Instructions for ALL
Folding Goals
SHEET
REVISION
1 OF
8
1
12

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FT-342 and is the answer not in the manual?

Questions and answers

Summary of Contents for MHGOALS FT-342

  • Page 1 For spares or assistance please get in contact with MH GOALS Via - - 01502 711 298 - Info@mhgoals.com - www.mhgoals.com MH Goals Ltd, Ellough Industrial Estate,...
  • Page 2 PARTS LIST ITEM PART NUMBER 32mm Back Bar 80mm Ali CrossBar 80mm Ali Post RH 80mm Ali Post LH 80mm Ali Crossbar FT-687 - Top Folding Hinge Weldment LH FT-2090 - Large Folding Goal Top Hinge Weldment LH FT-531 - Bottom Folding Hinge Weldment RH FT-530 - Bottom Folding Hinge Weldment LH FT-688 - Top Folding Hinge Weldment RH 80mm Ali Upright LH...
  • Page 3 Parts Required 80mm Ali Crossbar Extra channel nut goes here if using the larger hinges 80mm Ali Upright LH 80mm Ali Upright RH M8 Channel Nut DETAIL, D SCALE: 1 : 3 DETAIL, E SCALE: 1 : 3 Step 1 - Take the crossbar and both post weldments and lay them all out on a flat surface with the channel in the back facing upwards.
  • Page 4 Parts Required Top Folding Hinge Top Folding Hinge Weldment LH Weldment RH Bottom Folding Hinge Bottom Folding Hinge Weldment LH Weldment RH DETAIL, F SCALE: 1 : 2.5 M8 Spring Washer M8 x 20 Hex Head Bolt DETAIL, G SCALE: 1 : 2.5 DETAIL, H SCALE: 1 : 2.5 DETAIL, J...
  • Page 5 Parts Required DETAIL, K 32mm Round SCALE: 1 : 2 End Cap DETAIL, N SCALE: 1 : 2.5 Back Bar Bracket M10 x 50 Hex Head Bolt DETAIL, M SCALE: 1 : 2.5 M10 Nyloc DETAIL, P SCALE: 1 : 2.5 DETAIL, L SCALE: 1 : 2.5 DETAIL, R...
  • Page 6 Parts Required M10 Spring M10 Nyloc DETAIL, S Washer SCALE: 1 : 2.5 M6 Washer M6 Nyloc DETAIL, T SCALE: 1 : 2.5 M10 Bolt Cap M6 Bolt Cap M10 x 60 Hex Head Bolt M6 x 55 Hex Head Bolt DETAIL, V SCALE: 1 : 2.5 DETAIL, U...
  • Page 7 Parts Required 32mm Back Bar Spring Clip PLEASE NOTE THAT ON A 24 X 8 THE BACK BAR IS SPLIT INTO 2 SECTIONS, THIS WILL BE SECURED TOGETHER BY SLIDING THE SWAGED (REDUCED) END OF ONE SECTION INTO THE OTHER HALF, LINING UP THE HOLES AND FASTENING USING THE SUPPLIED M10 X 45 HEX HEAD BOLT &...
  • Page 8 Parts Required Step 6 - The Back Bar is part of the structure of the goal, and MUST be attached and anchored in place when in use Anchor at both ends near the Back Bar Bracket As indicated by the Anchor Point Stickers 2 x FT 602 - U Peg DETAIL, Y SCALE: 1 : 3...

Table of Contents