Advertisement
Quick Links
Advertisement
Summary of Contents for CH-SYS SC-406S
- Page 1 Speed Control SC-406S USER MANUAL 操作使用說明書 第 0 頁...
-
Page 2: Table Of Contents
7. Parameter 01 Programming ． ． ． ． ． ． ． ． ． ． ． ． ． ． ． 7 8. Parameters Explanation ． ． ． ． ． ． ． ． ． ． ． ． ． ． ． ． ． ． ． 8 EMAIL:chih.mail@mas.hinet.net Http://www.ch-sys.com 第 1 頁... -
Page 3: Functions Of Control Panel
MODE + ▲ → from low to high (Acceleration) MODE + ▼ → from high to low (Deceleration) 2. Method for moving decimal point: SET + ▲ or ▼ to move the decimal points from left to right. EMAIL:chih.mail@mas.hinet.net Http://www.ch-sys.com 第 2 頁... -
Page 4: External Dimension For Installation
2.External Dimension for Installation 100m/m SPEED CONTROLLER SPEED 100m/m ○ RUN SPEED ○ PRG ○ ERR SC-406s 160m/m 90m/m Panel opening: 92 x 92 m/m EMAIL:chih.mail@mas.hinet.net Http://www.ch-sys.com 第 3 頁... -
Page 5: Standard Connection
2. After finishing system adjustment, please open Terminals 15 and 17 to avoid parameters modified. 3. D/A and signals wirings don’t set near or with power lines. 4. When the distance of signal cable is far from master (motor/inverter and so on), please add isolated interface. EMAIL:chih.mail@mas.hinet.net Http://www.ch-sys.com 第 4 頁... -
Page 6: Explanations Of Terminals
Terminals 15 & 19 are speed deceleration contact A. D/A Output Terminals 20 & 21 are D/A output 0~10V to inverter or DC controller. Please use metal-shielded cable and isolated to power lines. ※Power source (+) and (-) must not be reversed. EMAIL:chih.mail@mas.hinet.net Http://www.ch-sys.com 第 5 頁... -
Page 7: Parameters Setting Method
＊If the setting is 30, the result is 3 second. Higher of the value of parameter 02 and 03 results slower response time. Parameter 04, 05 and 06 have to modify depending on actual situation. EMAIL:chih.mail@mas.hinet.net Http://www.ch-sys.com 第 6 頁... -
Page 8: Parameter 01 Programming
7.Parameter 01 Programming The indicator of【◆】 ：406S equipped functions Parameter Range Position Auto-signal Recovery Upper LCD Display Tracing Input Feedback (memory) Content for E1/E2 Function Linear Signal-tracking Speed Indicator ◆ 0000 ◆ ◆ 0001 ◆ ◆ ◆ 0002 ◆ ◆ ◆... -
Page 9: Parameters Explanation
2. Adjust panel display to be 1000. 3. Start processing, then detect actual (linear) speed. 4. Adjust panel display to make actual (linear) speed equal to Pr04. 5. Change Pr04 to be the value of panel display. EMAIL:chih.mail@mas.hinet.net Http://www.ch-sys.com 第 8 頁... - Page 10 Additional Setting range : 0 ~ 255 Factory setting : 30 Description : During executing function, urgent accelerating time unit is 0.1 second/ For example： Pr07=30, actual executed time is 3 second (30 x 0.1). EMAIL:chih.mail@mas.hinet.net Http://www.ch-sys.com 第 9 頁...
- Page 11 第 10 頁...