Summary of Contents for Incam LCW-20P
- Page 1 © 2021 Incam Systems Wireless Control Unit for SONY Camera LCW-20P Operation Instruction Before operating the unit, please read this instruction thoroughly and retain it for future reference. 1st Edition (Revised 3) English...
-
Page 2: Table Of Contents
© 2021 Incam Systems Table of Contents Overview ......................1 System Configuration ................... 2 Location and Function of Parts ..............3 Operating the Menu ..................5 Menu Settings ....................6 Specifications ....................8 Notes ......................9... -
Page 3: Overview
① The 12V tally power output can only be used for Incam tally lamp (optional). The unit need to be power off before connecting the tally lamp, otherwise, the unit may be damaged. -
Page 4: System Configuration
SONY摄像机 LCW-20P LCW-20P SONY RCP LCW-20P connects SONY camera and control panel directly Long-distance connection example SONY摄像机 LCW-20P LCW-20P FPT-S2E1 SONY RCP FPT-S2E1 LCW-20P connects SONY camera and control panel through FPT-S2E1 portable multi-purpose optical transmission units via SMPTE cable... -
Page 5: Location And Function Of Parts
© 2021 Incam Systems Location and Function of Parts No. Item Introduction to function Antenna connector A Connect omnidirectional antenna (Short) (2.402~2.482 GHz) Antenna connector B Connect omnidirectional antenna (Tall) (902~928 MHz) Master connects control panel Master/Slave identifier Slave connects camera... - Page 6 © 2021 Incam Systems Power connector pin assignment No. Definition Description Ground POWER 9~18V Data connector pin assignment No. Definition Description Ground RXD+ Serial data input+ RXD- Serial data input- TXD- Serial data output- TXD+ Serial data output+ Not connected...
-
Page 7: Operating The Menu
© 2021 Incam Systems Operating the Menu Left Right Down Press the menu control button to display the menu screen, push left and right to switch between menu pages, push up and down to change settings, and press to change parameters. Switch to save menu page to save all the changes, and the unit will automatically restart for the changes to take effect. -
Page 8: Menu Settings
© 2021 Incam Systems Menu Settings Startup screen The unit starts in about 90 seconds. HOME Display wireless signal strength, frequency, ID, band width and RCP/CAM. GROUP_ID The ID can be changed in the range 11~61, please note that the ID of master (RCP) and slave (CAM) unit must be set to the same. - Page 9 © 2021 Incam Systems TX_Power Transmission power can be selected from low, medium and high. RF_Delay RF Delay can be adjusted from 1 to 600. SAVE Save all parameter settings. Caution! Do not cut off power supply during saving procedure, the unit will be permanently damaged! ...
-
Page 10: Specifications
© 2021 Incam Systems Specifications General Power requirements 9~18V DC Power consumption Transmitting power 1W (max.) Transmitting distance 1000m Operating temperature 5 °C to 40 °C (41 °F to 104 °F) Storage temperature -20 °C to +60 °C (-4 °F to +140 °F) -
Page 11: Notes
© 2021 Incam Systems Notes If the unit is suddenly taken from a cold to a warm location, or if the ambient temperature suddenly rises, moisture may form on the outer surface of the unit and/or inside of the unit. This is known as condensation. If condensation occurs, power off the unit and wait until the condensation clears before operating the unit. - Page 12 © 2021 Incam Systems Miscellaneous notes To reduce the risk of fire or electric shock, do not expose this unit to rain or moisture. To avoid electrical shock, do not open the housing. Refer servicing to the manufacturer or local distributor for maintenance.
- Page 13 © 2021 Incam Systems Incam products include: robotic rail camera systems, remote control pan/tilt heads, universal camera wireless control systems, portable optical transmission systems, multi-channel 4K optical transmission systems, SMPTE/LC optical cable converter, remote control panels, micro cameras, customized products, etc.
Need help?
Do you have a question about the LCW-20P and is the answer not in the manual?
Questions and answers