Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Feed Mill FME-WBHP-2300
- Page 1 USER MANUAL WORKBENCH WITH HYDRAULIC PRESS FME-WBHP-2300...
-
Page 2: Table Of Contents
Conditions Of Use Machine-Overview MAINTENANCE AND REPAIR Introduction Security During Maintenance Maintenance Instructions Repairs Storage CONTROL ELECTRICAL DIAGRAM EC-DECLARATION OF CONFORMITY TECHNICAL CHANGES RESERVED Feed Mill Services & Equipment BV – Tel. +31 (0)493 310 059 – www.feedmillservices.eu - 2 -... -
Page 3: General Information
The Netherlands Tel: +31 (0)493 310 059 ----------------------------------------------------------------------------------------------------------------------------- Date of issue at Feed Mill Services & Equipment BV: October 2018 TECHNICAL CHANGES RESERVED Feed Mill Services & Equipment BV – Tel. +31 (0)493 310 059 – www.feedmillservices.eu - 3 -... -
Page 4: Iib-Marking
This means that the machine complies with the IIB-marking. The Declaration of Conformity (included in this manual) indicates the guidelines applicable to this machine. TECHNICAL CHANGES RESERVED Feed Mill Services & Equipment BV – Tel. +31 (0)493 310 059 – www.feedmillservices.eu - 4 -... -
Page 5: Introduction
When the workbench is surrendered, it is intended that this user manual is also transferred. Treat this instruction carefully. It is not allowed to change or delete pages. Feed Mill Services & Equipment BV reserves the right to replace parts of this manual, in the context of the improvement of the product, at any time without directly providing a new edition. -
Page 6: Individual Means Of Protection
The following provisions and recommendations are primarily based on observing the rules of the safety regulations mentioned in this manual. Feed Mill Services & Equipment BV isn’t responsible for possible damage to persons or goods related to ignoring of the safety regulations and instructions in this manual. -
Page 7: Operational Restrictions
Ensure that hot surfaces can’t be touched. Touching hot surfaces can lead to severe burns. Improper use of environmentally-friendly and hazardous substances can cause serious damage to the environment. TECHNICAL CHANGES RESERVED Feed Mill Services & Equipment BV – Tel. +31 (0)493 310 059 – www.feedmillservices.eu - 7 -... -
Page 8: Marking
Unreadable labels, symbols, etc. can lead to danger. They can become dirty or unreadable over time. Therefore: - Labels, symbols, etc. must be clearly legible. - Damaged labels, symbols, etc. must be replaced. For this we advise you to contact Feed Mill Services & Equipment BV. TECHNICAL CHANGES RESERVED Feed Mill Services &... -
Page 9: Transport
Check also if the delivery correspondents to the order. When unloading should carefully be made to the equipment. Report any defects or damage immediately to Feed Mill Services & Equipment BV and to the carrier responsible for the damage during the transport. -
Page 10: Installation And Commissioning
Whether all hydraulic connections still be in tact Warning! The risks of improper functioning are greater than normal during business counting. Take additional safety measures where necessary. TECHNICAL CHANGES RESERVED Feed Mill Services & Equipment BV – Tel. +31 (0)493 310 059 – www.feedmillservices.eu - 10 -... -
Page 11: Specifications
Voltage: 230 V Tank capacity: Max. hydraulic pressure: 210 bar Speed: <10 mm/sec Figure 4.1.1 Workbench with hydraulic press FME-WBHP-2300 TECHNICAL CHANGES RESERVED Feed Mill Services & Equipment BV – Tel. +31 (0)493 310 059 – www.feedmillservices.eu - 11 -... -
Page 12: Conditions Of Use
2. Hydraulic Cylinder Drawer Unit 3. Handle Aggregate 4. Terminal box incl. Control panel incl. Emergency stop on/off switch (rear side) TECHNICAL CHANGES RESERVED Feed Mill Services & Equipment BV – Tel. +31 (0)493 310 059 – www.feedmillservices.eu - 12 -... -
Page 13: Maintenance And Repair
- Do not use abrasive or corrosive materials or solvents when cleaning the hydraulic press. Do not use any cleaning agents that affect the parts and/or cause corrosion. TECHNICAL CHANGES RESERVED Feed Mill Services & Equipment BV – Tel. +31 (0)493 310 059 – www.feedmillservices.eu - 13 -... -
Page 14: Maintenance Instructions
- The filters and the oil must be replaced with great maintenance. Figure 5.3.1 Aggregate at the bottom of the workbench TECHNICAL CHANGES RESERVED Feed Mill Services & Equipment BV – Tel. +31 (0)493 310 059 – www.feedmillservices.eu - 14 -... -
Page 15: Repairs
Direct switching can cause damage to the machine and danger to the operator. Let the machine first acclimatize. TECHNICAL CHANGES RESERVED Feed Mill Services & Equipment BV – Tel. +31 (0)493 310 059 – www.feedmillservices.eu - 15 -... -
Page 16: Control
In an emergency situation, press the 'Emergency Stop' (red button) shown in figure 6.2 Figure 6.1 Figure 6.2 ‘On/Off’ button Control panel TECHNICAL CHANGES RESERVED Feed Mill Services & Equipment BV – Tel. +31 (0)493 310 059 – www.feedmillservices.eu - 16 -... -
Page 17: Electrical Diagram
7. ELECTRICAL DIAGRAM TECHNICAL CHANGES RESERVED Feed Mill Services & Equipment BV – Tel. +31 (0)493 310 059 – www.feedmillservices.eu - 17 -... -
Page 18: Ec-Declaration Of Conformity
This Declaration of conformity and the CE marking on the type plate are valid for the workbench with hydraulic press which is part of the Feed Mill Services & Equipment BV delivery. When this workbench is built into a larger system, the manufacturer of this system (this can also be the operator) must carry out the conformity review process for this large system according to machinery Directive 2006/42/EC, the Declaration of Conformity and provide the system with the CE marking. - Page 19 Feed Mill Services & Equipment BV Dr. H. van Doorneweg 38 5753 PM DEURNE The Netherlands Phone: +31 (0)493 310 059 E-mail: info@feedmillservices.eu Website: www.feedmillservices.eu TECHNICAL CHANGES RESERVED Feed Mill Services & Equipment BV – Tel. +31 (0)493 310 059 – www.feedmillservices.eu - 19 -...
Need help?
Do you have a question about the FME-WBHP-2300 and is the answer not in the manual?
Questions and answers