Advertisement
Quick Links
Advertisement
Summary of Contents for elaman TSE 6802
- Page 1 Product Information TSE 6802 System Operation...
- Page 2 TSE 6802 System Operation The set is designated for a monophonic or stereophonic wireless audio signal transmission within 420 MHz band to a distance according to the transmitting power and field conditions. Due to digital modulation, a better audio transmission quality is acquired during a weak signal in the noise threshold in comparison with the analogue systems.
- Page 3 Transmitting Units LOKE STANDARD TRANSMITTER Dynamics compressor Rising time approx. 0.1 s, falling time approx. 4s Switch-off time in VOX regime 13 seconds after acoustic stimulus dies away Crosstalk between audiochannels 40 dB (depending on audio frequency) RF power / DC consumption (typical values) CONFIDENTAL page 3...
- Page 4 HI Power 300mW / 130mA - supply voltage 12V (max) 170mW / 95mA - supply voltage 6V (nominal) 80mW / 90mA - supply voltage 3.6V (min) LO Power 15mW / 54mA - supply voltage 12V (max) 12mW / 52mA - supply voltage 6V (nominal) 10mW / 50mA - supply voltage 3.6V (min) Spurious RF products <...
- Page 5 Loke High Power Transmitter – 2W Stereo inputs: Audio line 0.7V (ef) Microphone (electret, 3V bias ntroduced through 4.7kW resistor) Digital input/output: TTL audio signal data stream input TTL remote control signal output Dynamics compressor: Rise time 0.1s (approx.), fall time 4s (approx.) Switch-off time in VOX mode: 13 seconds after acoustic stimulus or data stream dying down...
- Page 6 Line input – It is being utilized for processing the signal of a standardized line level from other audio devices, e.g. various recording instruments, etc. Digital input/output – This connector is being utilized for the direct data interconnection with the LOKE receiver and this way a repeater station may be created.
- Page 7 Receiving operating period Up to 10 hours depending on battery quality and use of remote control command (without display backlight) Ext. source polarity reversal May lead to a damage - not permitted! Int. battery polarity reversal May lead to a damage - not permitted! Climatic oper.
- Page 8 Remote control function - Push buttons on the keypad are limited by a darker field. Their immediate status is shown on the display. A flashing COMMAND sign on the upper left side indicates the display initial command regime. Terms of the remote control status push buttons. MONO / STEREO Switches between one - and two channel transmission.
- Page 9 Batteries – The unit is supplied by 2 AA cells. By choosing high quality batteries like Duracell Ultra M3, the receiver will be able to operate up to 10 hours (with a limited use of the remote control functions). The batteries will be electronically disconnected if an external power supply is used. External supply voltage - The maximum allowed voltage value is 15V and the minimum is 8V.
- Page 10 In a repeater unit the filter is being utilized for preventing of a strong signal penetration back to the receiver. It comprises the combination of a band pass and band-stop filters and is precisely tuned up to required channels. This filter has to be installed in the repeater unit both on the transmitting and receiving sides.
- Page 11 To set further regime-parameters require using push buttons in the darker field on the keypad (ADDRESS, MONO-STEREO, HIPOW-LOPOW, VOXCONT) Via these regime-parameters the transmitter is activated by pushing the ACT button. WARNING (!!!) - After every change of the regime-parameters it is necessary to execute the activation (update) again by using the ACT push button in order to transfer the changes transferred to the audio transmitter.
- Page 12 For this reason, it is necessary to set the address equal with the own transmitter on the repeater receiver (!!!). Only this way the both units will correctly respond to the remote control commands and will mutually co-operate. After an addressable reception of a valid command for the repeater station the last will be automatically set out.
- Page 13 CONFIDENTAL page 13...
-
Page 14: Warranty
Notes Working Temperature LOKE is being set-up and adjusted at Gamma’s premises under room temperature for which the specifications are referred to in the introduction. Although LOKE is constructed for operations in increased working temperature ranges, the temperature changes can cause the transmission specifications to get slightly worse. - Page 15 If you would like further Information about ELAMAN, or would like to discuss a specific requirement or project, please contact us at: Elaman GmbH German Security Solutions Seitzstr. 23 80538 Munich Germany Tel: +49-89-24 20 91 80 Fax: +49-89-24 20 91 81 info@elaman.de...
Need help?
Do you have a question about the TSE 6802 and is the answer not in the manual?
Questions and answers