Summary of Contents for SKININC Tri-Light Body Sculpt Fit
- Page 1 Y OUR 3 6 0 B OD Y W OR KO UT REI NVEN T ED . Gl ow. L i ft . S mooth . NA S A - I ns p ire d .
-
Page 2: Table Of Contents
Contents 1. To Start With a. Overview Of Product b. Product Composition c. Detailed Modes 2. How To Operate a. Product Suitability b. Precautions c. Remaining Battery Check d. Power On/Off e. Low battery during use f. How To Use In Standby Mode g. -
Page 3: Overview Of Product
Overview Of Product Turn on the Power of Customization for your body with Tri-Light™ Body Sculpt Fit, Skin Inc’s innovative LED treatment. This revolutionary, non-invasive and anti-shock microcurrent treatment is a 4-in-1 that helps to tone, lift, contour, brighten, and smooth appearance of problem skin, with zero downtime. -
Page 4: How To Operate
How To Operate Product Not Suitable For: • Persons undergoing dermatological treatment • Ear, Eyes, Mouth • Persons with metal allergies or acne dermatitis • Excessively tanned skin • Skin with lesions or open wounds • Hemorrhagic area • Persons with severe heart disease •... -
Page 5: Remaining Battery Check
Remaining Battery Check Before using the device, you can check the remaining battery level from the color of the charging indicator by shortly pressing the power button once. Green charging indicator: The battery is fully charged / close to being fully charged. Yellow charging indicator: The battery is enough. -
Page 6: Low Battery During Use
Low Battery During Use The charging/status indicator flashes in red for 5 seconds with a beep sound and then the power is turned off with a 'beep-beep' sound. How To Use In Standby Mode When the operation of each mode is completed, the mode indicator flashes after a short beep sound and the device goes into the standby mode. - Page 7 WARM Mode (Warming at 42° C / 107.6° F) When the mode starts, the charging indicator flashes in white with a beep sound and preheating starts. Preheating takes about 1.5 - 3 minutes. The beep sound stops when preheating is over. Please use the device when preheating is complete. (The time to preheat the device may vary depending on the ambient temperature.) 1) Ensure skin is clean and dry prior to usage.
- Page 8 LIFT Mode (Red LED Therapy) When the mode starts, the charging indicator flashes in red with a beep sound and preheating starts. Preheating takes about 1.5 - 3 mins. The beep sound stops and micro-vibration starts when preheating is over. Please use the device when preheating is complete.
-
Page 9: How To Charge
How To Charge Charging USB Charging adapter connector Charging in Charging USB charging cable USB charging cable progress complete • When using the device for the first time after the purchase, use it after charging it for at least one hour. •... -
Page 10: After Use
After Use After using the device, hold down the switch to turn off the power and thoroughly wipe off any skincare remaining on the metal head with a cloth or cotton pad. Do not submerge the device in water or wash it under running water. Caution •... -
Page 11: How To Dispose The Product
How to Dispose The Product Do not dispose of this product as household waste. Recycle the product or its battery upon disposal to help conserve natural resources and protect the environment. Please contact the local recycling center if you are unsure about disposal. Product Specification Model Tri-Light™... -
Page 12: Faqs
FAQ: Q: I feel a tingling and prickling sensation when the device touches my bare skin. A: Micro-Current from Iontophoresis may cause a tingling sensation on your skin. Q: My skin became irritated from usage and persists while I am not on the device. A: Stop using the device and consult an expert.
Need help?
Do you have a question about the Tri-Light Body Sculpt Fit and is the answer not in the manual?
Questions and answers