Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Hydraram HDG-110R
Summary of Contents for Hydraram HDG-110R
-
Page 1: Part List Total
CE Opera ting and Maintenance Manual Demolition and Sorting Grab HDG-110R... -
Page 2: Part List Total
Refer to the safety regulations before starting on any maintenance or repair work. • Replace defective parts only with original parts from Hydraram. • Failure to replace defective parts with original parts from Hydraram will result in • cessation of the entire warranty and CE liability. -
Page 3: Table Of Contents
Index Content Page EU declaration of compliance Safety regulations Conditions of guarantee Operation Daily maintenance Lubrication schedule Exploded view Total Part list Total 1 Part list Total 2 Partslist + exploded view Cylinder Partslist + exploded view C.O.D. Tightening Torques S803-D CE MANUAL 03-2018... -
Page 4: Eu Declaration Of Compliance
Attention: Any adjustment that is made to this product without written consent on Hydraram, makes this declaration void and invalid. We should draw your attention to the fact that the demolition grab product is designed to... -
Page 5: Safety Regulations
Hydraram is used, then you must assure yourself that it is safe for you and others. You should also ensure that the product will not be damaged or made unsafe by the... -
Page 6: Conditions Of Guarantee
Any claim made under guarantee will only be taken into consideration once a written appeal is made to the dealer or Hydraram. This must be done directly after the damage or fault occurs and at least within 24 hours of any irregularities and problems arising. -
Page 7: Operation
Procedures to follow before initial use Before taking the machine into operation and to ensure the good functioning of the a- pparatus, it is important that the following points are checked and correspond to the tech- nical specifications as shown on the information plate and in the manual. The type and weight of the sorting grab must conform to weight and machine class •... -
Page 8: Daily Maintenance
Daily Mai ntenance For maintenance work, always place the grab in open position on a flat and stable surface and ensure the excavator cannot move. During maintenance on the hydraulic system the hydraulic hoses need to be disconnected. Before disconnecting ensure there is no pressure on the hoses. Consult the manual for the excavator. -
Page 9: Lubrication Schedule
Lubrication Schedule Picture 3: Lubricating pivoting points 1 = Lubricate 1 x per 8 operating hours. Picture 4: Lubricating pivoting points 1 = Lubricate 1 x per 8 operating hours. Picture 5: Lubricating rotator 1 = Lubricate 1 x per 8 operating hours. -
Page 10: Exploded View Total
Exploded View HDG-110R TOTAL... - Page 11 Partslist HDG-110R TOTAL Part No. Description Order part No. Welded main frame construction S803D.001 Shell left (short lever) S803D.002 Shell right (long lever) S803D.003 Welded rotator frame construction S803D.004 Welded linkage construction S803D.005 Hydraulic cylinder right (high nipple) S803D.006 Hydraulic cylinder left (low nipple) S803D.007...
- Page 12 Partslist HDG-110R TOTAAL Part No. Description Order part No. Bolt set slewing ring S803D.030 1 set Locker-u S803D.031 Connector block C.O.D. S803D.032 O-ring to C.O.D. (2 pcs) S803D.033 1 set 1 set Bolt set connector block C.O.D. (2 pcs) S803D.034 Protective cover (connection nippels) S803D.035...
-
Page 13: Partslist + Exploded View Cylinder
Partslist cylind er left HDG-110R Part No. Description Order part No. Cylinder housing (low connection / 2 ports) S803D.101 Piston rod S803D.102 Cylinder nut S803D.103 Piston S803D.104 Bearing cylinder housing S803D.105 Bearing cylinder nut S803D.106 1 set Cylinder seal kit S803D.107... -
Page 14: Partslist + Exploded View C.o
Partslist cylind er right HDG-110R Part No. Description Order part No. Cylinder housing (high connection / 4 ports) S803D.112 Piston rod S803D.102 Cylinder nut S803D.103 Piston S803D.104 Bearing cylinder housing S803D.105 Bearing cylinder nut S803D.106 1 set Cylinder seal kit S803D.107... -
Page 15: Tightening Torques
S803D.206 1 set Bolt set C.O.D. connection block (2 pcs) S803D.207 1 set Rotor seal kit C.O.D. S803D.208 1 set Connection nipples C.O.D. housing (2 pcs) S803D.209 1 set Connection nipples connection block (2 pcs) S803D.210 Exploded view C.O.D. HDG-110R... - Page 16 Torques Specification Maximum torque specified to bolts on the cutting blades and rotator of the demolition and sorting grab. Please consult this listing on diameter, pitch and metric size and maximum torque specified prior to fastening. Bolt size Torque (Nm) Torque (Kg/m) Bolt 10,9 Bolt 10,9...
Need help?
Do you have a question about the HDG-110R and is the answer not in the manual?
Questions and answers