Advertisement
Quick Links
Installation Manual
SAAB 9-5 2009-2011
Interface with HDMI Mirroring
Part #: NAVTOOL6.0-LG1
NOTICE: Navtool recommends having this installation performed by a certified technician.
Logos and trademarks used here in are the properties of their respective owners.
1
SAAB 9-5 2009-2011
Advertisement
Summary of Contents for NAV TOOL SAAB 9-5 2009-2011
- Page 1 Installation Manual SAAB 9-5 2009-2011 Interface with HDMI Mirroring Part #: NAVTOOL6.0-LG1 NOTICE: Navtool recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. SAAB 9-5 2009-2011...
- Page 2 Print End Pages 1-4 and give them to the customer Open the camera app on your smart- phone and point your rear camera at the QR-Code to scan it. Finally, tap the pop up banner to open support website. SAAB 9-5 2009-2011...
- Page 3 • Make sure you are not connecting to any data wires; always check your connections with a multi- meter. • Always use help of a professional installer to prevent any damage to the vehicle or NavTool interface. SAAB 9-5 2009-2011...
- Page 4 USB Configuration Cable NavTool Interface NavTool LVDS Cables (Part # NT-USB-CNG) (Part # NAVTOOL6.0-LG1) (Part # NT-GMBLU-LVDS) NavTool Vehicle Specific NavTool AUX Activator NavTool Interface Harness Plug and Play Harness (Part # NT-AUX-ACT) (Part # NT-WHNT6) (Part # NT-GMQUAD-BLU) SAAB 9-5 2009-2011...
- Page 5 If the green LED is not ON, the interface HDMI port will not work. USB Port for Apple CarPlay and Android Auto- Not Used HDMI Port- HDMI port is dedicated for connecting video sources such as iPhone mirroring, Android Mirroring, Apple TV, Roku, FireStick, Chromecast, PlayStation, Xbox, or similar devices. SAAB 9-5 2009-2011...
- Page 6 In that case, this wire must be connected to the vehicle’s reverse +12V output. (Change setting “Manual Activation Wire as +12V Reverse Input” See page 41) +12V Output- 500 mA output can be used to drive a relay. This output provides +12V at all times when the vehicle is running. SAAB 9-5 2009-2011...
- Page 7 Quick Connection Guide NavTool Interface See Page 8 (Part # NAVTOOL6.0-LG1-NBT) Click NavTool Supplied Harness (Part # NT-WHNT6) Click Click NavTool Supplied Cable Factory Wire (Part # NT-GMQUAD-BLU) Back of Car Radio SAAB 9-5 2009-2011...
- Page 8 See Page 7 See Part 1 Factory LVDS Cable *2- Cable that previously used to be connected to blue connector in the back of the radio Click Close Up View of Radio Connectors Back of Car Radio SAAB 9-5 2009-2011...
- Page 9 2. 7 mm Socket- Example of a 7 mm socket tool is shown below. Any similar tool will do the job. It does not need to be the same as the picture below. SAAB 9-5 2009-2011...
- Page 10 Installation Instructions STEP 2 Continued Step 1: Remove the radio SAAB 9-5 2009-2011...
- Page 11 Installation Instructions STEP 2 Continued This page has been intentionally left blank. SAAB 9-5 2009-2011...
- Page 12 Reconnect previously removed radio connectors into the back of the radio. STEP 4 Connect supplied universal wiring harness (Part # NT-WHNT6) into plug and play harness (Part # NT-GMQUAD-BLU). (Part # NT-GMQUAD-BLU) (Part # NT-WHNT6) (For complete image, see Quick Connection Guide on page 7) SAAB 9-5 2009-2011...
- Page 13 Step 1: Connect the 4 pin plug from the vehicle specific supplied harness (Part # NT-GMQUAD-BLU) to the 4 pin microphone input connector on the NavTool Interface Harness (Part # NT-WHNT6). NavTool Supplied Harness (Part # NT-WHNT6) Click End View of Harness NT-GMQUAD-BLU SAAB 9-5 2009-2011...
- Page 14 Step 1: Connect NavTool supplied LVDS cable into the blue port on the back of the radio. Step 2: Connect NavTool supplied LVDS cable into the brown port shown in the image below. NavTool Interface Click See Page 15 See Part 1 Back of Car Radio Click Close Up View of Radio Connectors SAAB 9-5 2009-2011...
- Page 15 • If you are adding side or front cameras, install them and plug them into the appropriate camera RCAs. • If you are installing any HDMI or streaming devices, connect it to the HDMI port of the NavTool. SAAB 9-5 2009-2011...
- Page 16 After the interface is installed and you activate the NavTool, if your screen is blinking or you see a NavTool image for a second and it goes to a black screen, you must cut a wire on the harness. Cut pin 10 This is a front view of the connector NOT wire side SAAB 9-5 2009-2011...
- Page 17 FM, or XM, if equipped, Disc, or AUX (Auxiliary). Must set a radio to auxiliary/AUX before activating NavTool to hear audio from car speakers. • Audio will not play through car speakers if AUX activator jack is not connected or radio is not set to AUX input. SAAB 9-5 2009-2011...
- Page 18 Change the setting to OFF, once the red dot is set to OFF (image shown on the left), click the SAVE button on the bottom right. Apple CarPlay/Android Auto (Auto ON Mode) only set it to ON if you do not plan Step: 3 to use HDMI or video inputs SAAB 9-5 2009-2011...
- Page 19 Press and hold the corner of the touch screen for a few seconds until the bottom menu appears on the screen, release the finger and hold the corner of the screen again to return to the factory menu. (See page 18 for details) SAAB 9-5 2009-2011...
- Page 20 • To test aftermarket left and right cameras, use left and right turn signals. Left and right cameras should display depending on the turn signal activated. • To exit HDMI input or any Camera inputs, tap the touch screen to bring up the bottom menu. After everything is tested and working, reassemble the vehicle. SAAB 9-5 2009-2011...
- Page 21 If all steps above are checked off, you will save time, money and have an extremely happy customer. All above steps eliminate any unnecessary customer comebacks to your shop. If you require any further assistance please call our tech support line, email or go online WWW.NAVTOOL.COM 1-877-628-8665 techsupport@navtool.com SAAB 9-5 2009-2011...
- Page 22 Press and hold one of the four corners of the touch screen to activate or deactivate NavTool interface. After you activated the interface, you will be brought to this screen that you can navigate using the factory touch screen. (See page 18) SAAB 9-5 2009-2011...
- Page 23 HDMI’s device screen and connected image will appear on the screen. To exit HDMI, tap the touch screen to bring up the bottom menu. No HDMI Signal You will get this message when selecting this input with no HDMI source connected to interface. SAAB 9-5 2009-2011...
- Page 24 (Note: This input will not display factory installed right lane watch camera) To exit Right Lane Watch Camera, tap the touch screen to bring up the bottom menu. SAAB 9-5 2009-2011...
- Page 25 The white bar in the middle shows the interface contrast setting. You can lower the contrast of the interface by tapping the minus on the left and increase the interface’s contrast by tapping the plus on the right. Save or cancel any changes you have made. SAAB 9-5 2009-2011...
- Page 26 Parking lines: Select this option if you are installing an aftermarket right lane watch camera and you wish to add distance lines to the camera image. SAAB 9-5 2009-2011...
- Page 27 Down check to save your changes. X to cancel your changes. You can move your parking lines down by selecting the down arrow for your selected parking line. SAAB 9-5 2009-2011...
- Page 28 Turn ON manual activation wire as reverse trigger if your manual Turn OFF: Most vehicles will have the manual activation wire tells you to or if done by an installer. (See page 18 for details) turned OFF. (See page 18 for details) SAAB 9-5 2009-2011...
- Page 29 How to Connect Rear Screens to Car With AV Input Examples of equiptment used if connecting or installing additional rear screens Car Monitor NavTool Interface HDMI to AV Adaptor 1 in 2 Out HDMI Splitter HDMI Sources SAAB 9-5 2009-2011...
- Page 30 How to Connect Rear Screens to Car With HDMI Input Examples of equiptment used if connecting or installing additional rear screens Car Monitor NavTool Interface Car HDMI Input 1 in 2 Out HDMI Splitter HDMI Sources SAAB 9-5 2009-2011...
- Page 31 FM, or XM, if equipped, Disc, or AUX (Auxiliary). Must set a radio to auxiliary/AUX before activating NavTool to hear audio from car speakers. • Audio will not play through car speakers if AUX activator jack is not connected or radio is not set to AUX input. SAAB 9-5 2009-2011...
- Page 32 NavTool interface. Press and hold the corner of the touch screen for a few seconds until the bottom menu appears on the screen, release the finger and hold the corner of the screen again to return to the factory menu. SAAB 9-5 2009-2011...
- Page 33 Do not change if installer has set this feature to OFF. has set this feature to ON. • Tap the text of the setting you want to change. This will turn the setting ON or OFF. • SAVE or CANCEL your changes. SAAB 9-5 2009-2011...
- Page 34 You can lower the brightness of the interface by tap- ping the minus on the left and increase the interface’s brightness by tapping the plus on the right. Save or cancel any changes you have made. SAAB 9-5 2009-2011...