Advertisement
Advertisement
Summary of Contents for Wemars 5218G
- Page 1 OPERATOR'S MANUAL 2-Cycle Chain Saw 5218G/5818G/5820G/6220G/6220C...
-
Page 2: Table Of Contents
Contents Introduction..............2 Troubleshooting............27 Safety................4 Assembly..............13 Operation..............16 Maintenance..............22... -
Page 3: Introduction
Introduction TROUBLESHOOTING CAUSE SOLUTION Operator's manual THE UNIT WILL NOT START OR STARTS BUT DOES NOT CONTINUE TO RUN READ ALL INSTRUCTIONS BEFORE OPERATING The unit was started incorrectly Follow all Starting and Stopping Instructions The carburetor mixture adjustment setting is incorrect Contact our service center Product overview The spark plug is fouled... - Page 4 To sharpen the cutting teeth Symbols on the product This product agrees with the applicable EAC directives Meaning the cutting teeth. information on the recommended dimension of Warning This product agrees with the on your product. applicable Ukraine directives 1. Make sure that the saw chain is correctly tensioned.
-
Page 5: Safety
the product has an accessory that is not the product is not repaired at an approved To sharpen the sa chain from the manufacturer or not approved by service center or by an approved authority. The cutter the manufacturer. Safety maintenance to the product if you are not Safety de nitions sure about the situation. - Page 6 Adjust the ar uretor To lea the spark arrester s ree To do ai te a e o the spark plu CAUTION: a et i stru tio s or operatio CAUTION: To adjust the idle speed idle speed. To lea the air lter Note:...
- Page 7 Always hold the product with your two Examine the drive sprocket for excessive Clean or replace the spark arrestor screen hands. Hold the front handle with your left wear and replace if necessary. hand and the rear handle with your right hand.
- Page 8 Maintenance The operator should remain on the uphill side of the terrain as the tree is likely to roll Turn the guide bar daily for more even or slide downhill after it is felled. WARNING: Read and understand wear. the safety chapter before you clean, Plan and prepare your path of retreat Make sure that the lubrication hole in the repair or do maintenance on the...
- Page 9 saw chain during the cut. Loss of control To limb a tree can result if the product touches an object in wood. ground. 2. Remove small limbs in one cut. Pinch-Kickback can occur when the saw If the log is supported on both ends, cut 1/3 chain suddenly stops during the cut.
- Page 10 cause the loss of control of the product To fell a tree by the operator. height. 1. Remove dirt, stones, loose bark, nails, staples and wire from the tree. 2. Make a notch 1/3 the diameter of the tree, perpendicular to the direction of the fall. 5.
- Page 11 he a ma c ma call el ve ec ve ev ces aw cha he e e s ee c eases The am saw cha ay e cha s me c ew w h a small s a sc ew he sc ew cl ckw s ec eas he sc ew c...
- Page 12 15.Run 10 seconds at normal idle speed. Cylinder ooded or death because of asphyxiation or carbon Examine the product for damaged parts. 16.Pull the throttle trigger slowly but fully for 5 monoxide. the damaged guard or part operates release. correctly. Examine for broken or incorrectly can occur.
-
Page 13: Assembly
3. Pull the choke control out fully. 9. If the engine starts or tries to start, push the Assembly choke control back fully position. 3. Put the guide bar above the bar bolts. WARNING: Read and understand Steer the guide bar to under clutch the safety chapter before you position. - Page 14 6. Make sure that the edges of the cutting 4. Fill the saw chain oil tank with the CAUTION: Do not use gasoline tensioning screw clockwise with the links are turned forward on the top edge of recommended saw chain oil. with an octane number less than combination wrench the guide bar.
-
Page 15: Operation
ADJUSTING THE CHAIN TENSION Operation CAUTION: The chain must be WARNING: Read and understand the safety chapter before you tensioned whenever the on the operate the product. drive links hang out of the bar groove. Check for proper chain tension before starting CAUTION: the unit and periodically during operation.