Advertisement
The range
SMS Alert 9 is developed to connect to an existing alarm system or equipment to be monitored and
controlled. It is a 9
input,
home or business. It notifies you instantly when the inputs are triggered by sending an SMS and missed call
to four cellphones. You can phone the unit and listen in for possible intruders. As it is bi-directional, you can
also send the unit SMS messages and control remote systems. SMS Alert 9 can be configured as a two-
way intercom system using a Base Station intercom. The input strings and phone numbers of the
users are programmable by the user.
Examples: AC Loss/Restore, motion detection; temperature monitoring; computer server room control; 3-
phase imbalance; over/under voltage monitoring; field monitoring by using solar energy; opening of electric
gates; steamer room control & monitoring; farm water pump control and monitoring; air conditioning
monitoring and control; access control and monitoring, etc.
SMS Alert 1 works on the same principle than SMS Alert 9, but it is smaller and less expensive. It is a
programmable dual single
155mm x 75mm x 55mm. It also reports to four cellphones.
Input 1: (Dual option)
Can be set to send a SMS on both a Negative apply or Negative remove trigger. The SMS that will be
send is Programmable.
Examples:
Open your car with your cell phone when you accidentally locked your key in your car; receive a
SMS when your car alarm is on; activate pepper gas in your car; switch boiler rooms on, etc.
SMS Alert Alarm / Plus is a lockup-and-go alarm and does not require an existing alarm system. It is a 9 input,
1 switched relay
output,
SMS, remote control or key switch. It reports to four cellphones.
This is an upgraded SMS Alert 9 that connects to a BPT intercom system. This system enables your visitors to
call and talk to you from your intercom by pressing a button, where after you can open your gate via SMS.
The user can change the phone number as required. It reports to four cellphones.
SMS Alert 9
and 3 switched relay output unit that keeps you in constant contact with your
SMS Alert 1
input,
and 1 switched relay output device. The dimensions are approximately
SMS Alert 9 Alarm /Plus
LED and Siren output device. You can arm or disarm your SMS Alert Alarm via
SMS Alert 9 Intercom
Page 1 of 1
SMS Alert 9
Advertisement
Table of Contents
Summary of Contents for SMS Alert 9
- Page 1 & monitoring; farm water pump control and monitoring; air conditioning monitoring and control; access control and monitoring, etc. SMS Alert 1 SMS Alert 1 works on the same principle than SMS Alert 9, but it is smaller and less expensive. It is a programmable dual single input, and 1 switched relay output device.
-
Page 2: Sms Alert
SMS Alert 9 SMS ALERT 9 User Manual SMS Alert Version 8 *Input 1 : BURGLARY Input 2 : DISARMED , ARMED Input 3 : POWER LOSS, POWER RESTORED *Input 4 : 24 HOUR TEST *Input 5 : DURESS *Input 6... -
Page 3: Quick Start Steps
7. Airtime - Ensure that the SIM-card has sufficient credit. Load airtime if necessary. 8. Message Inbox - Ensure that the phone’s inbox is empty. Once empty, the SMS Alert will automatically keep the inbox empty. Page 3 of 3... - Page 4 SMS Alert 9 9. SMS 1234 b from your cellphone to the SMS Alert. Note the yellow LED will light up when B is active. This step notifies the SMS Alert that it must report to the pone from which the SMS was sent.
- Page 5 How to operate the microphone to silently listen in You are able to phone the SMS Alert and listen in for noises within a 20m radius. Phone the SMS Alert and wait for it to auto answer. It will auto answer automatically after two rings.
-
Page 6: Technical Specifications
Send 1234 02 to toggle this mode. Relay C will latch when input 2 is Arm/Disarm input to triggered. This can be used to arm/disarm the SMS Alert via +12V via relay switch relay C off C to the Key input. -
Page 7: Fault Finding / Troubleshooting
Interfacing to an Most alarm panels work on a negative closed loop principle. alarm panel SMS 1234 03 to the SMS Alert to change it to trigger on a negative power remove (removing negative power from the input). Fault finding / Troubleshooting... - Page 8 (version 7.5 and up SMS Alert is not built for a specific alarm panel. It is a generic solution that works on a negative trigger principle. The following diagram is a proposed example of how it can be connected to an alarm panel: Sensor e.g.
Need help?
Do you have a question about the 9 and is the answer not in the manual?
Questions and answers