Advertisement
Quick Links
www.netlinkict.com
High-Power Optical Amplifier
PTA5102Y-16
Description
The PTA5102Y-16Series Ytterbium and Erbium Doped Fiber Amplifiers (YEDFA) is designed for use in
CATV、 FTTX and HFC application. It is optimized for 1550nm wavelength and is packaged in a 2U 19"
rack housing. The product offering is flexible enough to perform all the requirements of CATV、FTTX
and HFC applications. The device chooses a high performance PUMP laser and circuit (include ACC and
APC) and optical output power is adjustable and flexible for network link loss budget. The
PTA5102Yseries also provide monitors and associated alarms for all vital characteristics. The status and
management of the device can be monitored and managed either from the LCD front panel display&
Web or remotely via Ethernet based-SNMP . The device also support multipul optical output by
build-in PLC splitter and FWDM (1310nm\1490nm) optical multiplexer for Triple-play FTTX network
applications.
Feature
Standard 19 inch 2U Rack YEDFA
16 output ports
Output powers range from 16*16&16*19&16*22dBm
Output power adjustable -3~0Db
Wide input dynamic range(-3to +10dBm)
High Isolated input & output(30dB for max)
Web browser management
Automatic Power Control (APC) or Automatic Current Control (ACC)
LCD Panel Status Indicator for local monitor
Remote management via SNMP (Ethernet Interface)
Advertisement
Summary of Contents for OPTON PTA5102Y-16
- Page 1 High-Power Optical Amplifier PTA5102Y-16 Description The PTA5102Y-16Series Ytterbium and Erbium Doped Fiber Amplifiers (YEDFA) is designed for use in CATV、 FTTX and HFC application. It is optimized for 1550nm wavelength and is packaged in a 2U 19” rack housing. The product offering is flexible enough to perform all the requirements of CATV、FTTX and HFC applications.
- Page 2 www.netlinkict.com Diagram...
-
Page 3: Specifications
Specifications Description Unit Value Conditions / Notes Optical Specifications TVinput:1550nm Fiber connector Output:1550nm SC/APC Input Power -3~+10 1550nm recommend +2~+10dBm Output Power 16*16,16*19,16*22 @+6dBm Input 16*16dBm Alarm range: Out of Laser Bias current Pump 3100mA±200mA 1800mA~4600mA @+6dBm input 16*19dBm Laser Bias current Alarm range: Out of Pump 3300mA±200mA... -
Page 4: Installation
Description Unit Value Conditions / Notes Mechanical Specifications Dimension 483 422 88 Carton:590 590 200 (LxWxH) Weight Net weight 11.5, gross weight :14.8 Mounting 19” EIA rack, 2U Rack Installation 1. Unpack Check the package for obvious damage. ... - Page 5 Fiber Patch Cord Connecter - Remove the fiber connector dust cap and wipe the connector. Use a microscope (100X or 200X) to check the end of the connector for scratches or debris. - If there are no scratches or debris, the connector is clean and ready for use. If scratches or debris are found, repeat the fiber patch cord connector cleaning procedure.
- Page 6 Control Front Panel Display and Alarms Outline the menu of High Power Optical Amplifier. For the description of all instructions, please refer to the panel shown below. Through the buttons on the right side of the LCD screen, you can scroll through all the menus of the large light.
- Page 7 Menu #2 - S/N Product Serial Number Menu #3 -Version: 2.4.1 Program Version Number Menu #4 -Rated Output Power Rated Output Power Menu #5 -Set Output Power xx.x dBm Menu# 6 -Laser Key State Laser Key State Menu #7 -Pin: Input Optical Power Menu# 8- Pout: Output Optical Power...
-
Page 8: Troubleshooting
IP address Menu#17 -IP GATEWAY IP gateway Menu#18 -IP MASK Subnet Mask 3 Menu Operation A. Key Settings 1> Switch the menu to the Laser Key State display page. 2> Press the “Enter” key and then press the “ESC” key, then press the “up” key or the “Down”... - Page 9 by the warning should not be ignored, and there may be lurking serious system failures. Status Working Status LED Color Description Display Current Key off The machine is not Laser Bias working, it is in the off state Chassis Above 55°C Alarm Temperature Input Input Low...
- Page 10 Connect the optical fibers of all ports before power on. The optical connector cannot be plugged or unplugged while the machine is working. The machine cannot move or shake while working.