Advertisement
Quick Links
Needed Tools
1/16", 3/32" & 5/64" Allen Drivers
3/16", 1/4" & 11/32" Hex Drivers or sockets
Hobby knife
Emery board, needle files or fine sandpaper
1/8" Reamer, (drill will work)
Shock or other non-marring pliers
Synthetic grease
Silicone shock oil (30 wt. recommended)
Optional Parts
Sealed gear differential case for Traxxis 2 WD
Bag A (you will also need the main chassis plate and front shock towers in this step)
Attach 30* nose plate to chassis using (2) 8-32x5/8" & 1 8-32x1/4" FHS. The longer screws go in the two holes toward the
front of the car and will protrude through the nose plate.
Attach front bulkhead to nose plate using (4) 8-32x7/16" FHS
Attach the front shock tower to the nose plate using (4) 4-40x5/16" BHS
Find (2) front suspension arms, (2) 1.52" inner hinge pins and (4) e-clips. Ream the inner and outer hinge pin holes in the sus-
pension arms & the hinge pin holes in the front bulkhead with a .125" reamer. The parts should move freely after assembly.
Using (2) 8-32x7/16" FHS, mount the front bumper mount to the nose plate
Prodigy SC Mod
Instruction Manual
Advertisement
Summary of Contents for FIVESEVEN DESIGNS Prodigy SC Mod
- Page 1 Prodigy SC Mod Instruction Manual Needed Tools 1/16”, 3/32” & 5/64” Allen Drivers 3/16”, 1/4” & 11/32” Hex Drivers or sockets Hobby knife Emery board, needle files or fine sandpaper 1/8” Reamer, (drill will work) ...
- Page 2 Front suspension arm assem- bled. Note; shock is mounted in center hole in arm. Bottom is retained with 4-40 x 1/2” BHS. Top with 4/40 x 5/16” BHS. Top of shock is mounted in upper outer hole. The camber link is mounted to the inner hole in the caster block on the front side of the block.
- Page 3 Bag B Insert (2) 6x10mm flanged and (2) 5x8x2.5mm bearings into each steering bellcrank as shown Attach the bellcrank ackerman plate to the steering bellcranks using (2) bellcrank insert nuts and (2) 4- 40x5/16” FHS and countersunk washers ...
- Page 4 Bag C Assemble adjustable rear arms by applying a small amount of grease to hole in slide nut and outside of part to ease assembly Using (1) 4-40x5/16” BHS and washer, (1) 4- 40x5/16” FHS together with (2) 4-40 lock nuts; as- semble the two halves of the rear arms as shown ...
- Page 5 Bag D Transmission and gear differential Install (4) .085x.600” pins as shown Slide (4) silver 14t gears onto pins (Note; they will be at different heights) Install (2) black outdrive gears into housing, there is a short pin that goes between the outdrive gears to align them ...
- Page 6 Install the .314” thick black delrin spacer between the transmission and the transmission brace using (4) 4-40x 5/8” BHS Insert CVD’s into the rear hub carrier’s, insert the drive pins through the axles then press firmly in on the axles while sliding the hex adaptors in place.
- Page 7 Bag G Attach rear body mount to the transmis- sion brace with 4-40 x 3/8” BHS and lock nuts Attach front body mount to chassis with 4-40 x 3/8” FHS and lock nuts Fix both battery mounts to chassis using 4-40 x 1/2”...