Related Manuals for Norden Secnor NAC-5008WA
Summary of Contents for Norden Secnor NAC-5008WA
- Page 1 NAC-5008WA WATERPROOF METAL ACCESS CONTROL IP66 User Manual www.nordencommunication.com...
-
Page 2: Specifications
INTRODUCTION The NAC-5008WA is a compact, waterproof stand-alone programmable access control system that provides proximity entry for up to 2000 users. It uses an Atmel micro controller assuring maximum performance in any environment, and the low- power circuit extends its service life. The products unique features are its simple design, easy operation, and high reliability. -
Page 3: Carton Inventory
Time Lock Output Load 2 Amp Maximum Environment Meets Ip66 Operating Temperature -40°C~60°C Operating Humidity 0% RH~ 98%RH Physical Zinc-Alloy Enclosure Surface Finish Powder Coat Unit Weight 260g(Square)/180(Mini) Shipping Weight 320g(Square)/260(Mini) Carton Inventory: Dimension: www.nordencommunication.com... -
Page 4: Installation
INSTALLATION Remove the back cover from the unit Drill 2 holes (A, C) on the wall for the screws and one hole for the cable Knock the supplied rubber bungs to the screw holes (A, C) Fix the back cover firmly on the wall with 2 flat head screws Thread the cable through the cable hole 9b) Attach the unit to the back cover Wiring... -
Page 5: Connection Diagram
CONNECTION DIAGRAM Common power supply Attention: A 1N4004 or equivalent diode is needed when use a common power supply, or the reader might be damaged. (1N4004 is included in the packing) www.nordencommunication.com... - Page 6 Common power supply Attention: A 1N4004 or equivalent diode is needed when use a common power supply, or the reader might be damaged. (1N4004 is included in the packing) www.nordencommunication.com...
- Page 7 Simplified Instruction Function Description Operation Enter the Programming Mode *(Master Code)# (123456 is the factory default master code) Change the Master Code O (New Master Code) # (Repeat New Master Code) # (Code :6 digits) Add Card User 1 (Read add cards )# (Can add Card continuously) Delete Card User 2 (Read Card )#...
- Page 8 Enter and Exit Program mode Programming Step Keystroke Combination Enter Program Mode *(Master Code)# Factory default is 123456 Exit Program Mode Set Master Code Programming Step Keystroke Combination Enter Program Mode *(Master Code)# Update Master Code 0 (New Master Code)# (Repeat New Master Code)# Exit Program Mode Add User Cards...
- Page 9 Delete User Cards Programming Step Keystroke Combination Enter Program Mode *(Master Code)# Delete Card : By read Card 2 (Read card )# Repeat Step 2 for additional user cards Delete Card : By user ID 2 (User card )# The User ID is any number from 1-2000. Delete Card : By Card Number 2 (Input 8/10 digit card number)# Set Relay Configuration...
- Page 10 Programming Step Keystroke Combination Enter Program Mode *(Master Code)# Strike-Out OFF 4 0 # (factory default) Strike -Out ON 4 1# Access will be denied for 10 minutes Strike-Out ON (Alarm) 4 2 # Set alarm time 5 (0~3)# Factory default is 1 minute Enter Master code # or Valid user card to silence Exit...
- Page 11 Reset to Factory Default: To reset to factory default, power off, press the Exit Button hold it and power on, there will be two beeps, and the LED light turns yellow. Release the exit button, then read any two 125KHz EM card/13.56MHz Mifare cards, the LED will turn red, indicating the reset to factory default was successful.
- Page 12 Operation Status Buzzer Exit from the program- Red Light bright One beep ming mode Open lock Green Light shines One beep Red light Shines quickly Beeps Alarm Operation error Three beeps www.nordencommunication.com...