Summary of Contents for FPQ 787
- Page 1 Electric Tying Machine User’s Manual CAUTION: READ THIS MANUAL CAREFULLY BEFORE USING THIS MACHINE...
-
Page 2: Table Of Contents
CAUTION: PLEASE UNFOLD PAGE WITH ILLUSTRATIONS TO KNOW THE FUNCTIONS OF THE MACHINE BEFORE READING. CONTENTS Safety Precautions ......................... 3 Safety Symbols ..........................3 General Safety Rules for Power Tools ..................5 Special safety instructions ......................7 Intended purpose ......................... 11 Function description ........................ -
Page 3: Safety Precautions
Safety Precautions Before first using the machine, please read this instruction manual carefully, for your own safety and for the safety of others. Please keep the manual in a safe place, if the owner changes, please transfer it to any subsequent owner to ensure that the information therein is available at any times. - Page 4 2. Symbols on Battery Mark as Ni-MH or Li-ion battery. Don’t dispose with household waste. Do not throw the battery into fire, otherwise it will cause explode. Do not dispose the battery in water or dank environment, otherwise it will explode or be damaged. Do not dispose the battery under strong light for a long time or on hot surface (Max temperature 60℃).
-
Page 5: General Safety Rules For Power Tools
General Safety Rules for Power Tools Warning! Read all safety directions and all instructions. Failure to follow all safety directions and instructions listed below may result in electric shock and fire and/or serious injury. Keep all safety directions and instructions for future reference. - Page 6 3.Personal safety 1).Keep alert, watch what you are doing and use common sense while shifting the power tool. Do not operate the power tool when you are tired, or under the influence of drugs, alcohol or medication. A moment of inattention when operating the power tool may cause serious personal injury.
-
Page 7: Special Safety Instructions
check the degree of wear of the parts and any other conditions that affect the power tool’s operation. If damaged, the power tool should be repaired before use. Many accidents are caused by poorly maintained power tool. 6).Keep the blade sharp and clean. Properly maintained blades with sharp cutting edge are less likely to be stuck and easier to control. - Page 8 personal injury. After tying action is completed, hold the handle to move the tying machine, the prudent usage of the tool will protect the operator effectively and extend the service life of the tying machine. 2.Other safety instructions In order to protect your personal safety, please wear suitable work clothing, such as non-slip boots, protective trousers.
- Page 9 can stretch out and retract smoothly and there is no interference of other foreign matters. Before staring the work of tying, please check objects hidden in grave vines or branches, for example, electric wire, iron wire, surplus branches and leaves, these things may affect the stretching out and retracting of the feeding hook.
- Page 10 2).Always check the charger, wire and plug before every use. If damaged, please contact qualified professional personnel for repair, and only use the original components. Do not use defective charger, and do not take apart it by yourself to ensure the safety of the equipment. 3).The charger's socket must be grounded.
-
Page 11: Intended Purpose
magnetic field may damage the function of medical implants under certain circumstances. In order to avoid serious injury, we recommend that the user with implant(s) consults a doctor and the producer(s) of the implant(s) before using this tool . Warning！ Do not touch the feeding hook or twisting wheel during the operation to avoid any personal injury. - Page 12 Display and Instruction Code Display Description Display Sign of Battery Sign of Battery Battery has 100% Battery Battery has 75% Battery has 50% Battery has 25% Battery has 10% Software over current Trouble Circuit fault Zero means normal Gear be stuck There is not 2 and 8 under voltage Overvoltage...
- Page 13 Button instruction Left button Trouble +/— Laps of knot Right button +/— How many times Touch left button or right button： Long press 3 seconds power Power button Long press 3 seconds power off.. enter Short press twice enters Laps of knot interface.
-
Page 14: Overview
twist, knot, and jamming is not included in quality assurance. Overview Components of the tying machine 1.Feeding tray 2.Tying wire 3.Wire pressing plate 4.Open button 5.Front cover 6.Wire pressing wheel 7.Display 8.Feeding hook 9.Operating position 10.Knotted wheel 11.Trigger 12.Handle 13.Battery Technical Parameters Parameters Electric tying machine... -
Page 15: Items Included
Ⅱ Protection class Charging time 4-5 h Items Included Open the package carefully and check whether the following parts are included: 1、 Tying machine 2、 Tying wire 3、 Battery 4、 Charger 5、 Tool box 6、 Instructions 7、 Maintenance manual 8、 Warranty card 9、... -
Page 16: Working Conditions
original equipment made battery pack provided by the Customer Center. · Always keep the applicable safety rules and environmental regulations and information in mind. 1． Keep the charger in a room at room temperature between + 10 ° C and + 22 ° C and avoid water entering. 2．... - Page 17 1、Open the pressing plate 2 、Press down the cover to rotate in accordance with the direction of the arrow, remove the cover. 4、Put in the wire, pay attention to the 3、Remove the cover outgoing line direction. 5、 Press down the cover and 6、Cover the plate rotate in the direction of the arrow.
- Page 18 8 、Use pliers to pull out the two binding wires. 7、 Put the end of wire in from the end of machine. 9. Pay attention to the direction of the thread and the plate is the same, no knots, distortion warp.
-
Page 19: Operation Instructions
Operation instructions Please wear appropriate clothing and work gloves when using this tool. Make sure the tool can operate normally before each use. The ON/OFF switch and safety switch must be normal. The power must be turned off when you loosen the trigger., Must stop using the tool if switch fails. -
Page 20: Tying Skills
and remove the binding machine. Tying skills 1． When the equipment is operating, keep your other hand be at least 5cm away from the area of tying mouth; don’t place your hand in the tying mouth. 2． Don’t use the equipment to tie the branches with a diameter more than 25MM, otherwise the machine may get stuck. - Page 21 Warning! 1. Do not pull the trigger when using tweezers to remove foreign matters from the cutter hole, otherwise the cutter will be damaged. 2.Please stop operation if the wire left only 20cm during using! Please take out the rest wire and replace the new one according to the follow steps.
-
Page 22: Cleaning And Maintenance
2、Take out the rest wire with pliers 3、Install the wire pressing wheel and put the top cover well. The machine can continue to work with the new wire. Cleaning and maintenance Don’t spray water on the equipment or immerse it in water, otherwise the equipment will be damaged. - Page 23 1、Press the button to push the 2. Remove the cover top cover if the machine is stuck or unable to feed wires. 3. Pull out the 4.Use a brush to clean up pressing wheel foreign matters in track as shown in the figure. After completion cleaning,...
-
Page 24: Storage
Storage 1、 To ensure the full charging of battery, don’t expose the equipment in an extremely hot or cold environment. 2、 If the equipment is not to be used for a long time, remove battery before storage. 3、 Battery and charger must be placed in the instrument box, prevent heat, dust, and moisture from entering, check if the switch is in OFF state. -
Page 25: Quality Guarantee
The equipment is not part of household waste. Send the equipment to a recycling center. The metal and plastic in the equipment can be recycled after be screened. For detailed information, please contact the Service Center. Do not discard the battery in household waste, fire (danger of explosion) or water. -
Page 26: Troubleshooting
Troubleshooting Problem Possible reason Corrective measures Battery is used up Charge The equipment Battery is not connected Connect battery cannot be started Cannot press down safety Start switch Invalid switch on/off Send to the Service Centre for repair Internal connecting line is Send to the Service Centre for repair Intermittent running loose... -
Page 27: Three Guarantees" Requirement
branches. adjust operation speed. Only after confirming the completion of tying action can the tying machine be lift up. Cannot charge The battery is not placed in Insert the battery correctly. The red indicator of the charger correctly. charger is blinking. The connection of charger Connect them correctly and power supply is not... - Page 28 complete machine and main components within the range of "Three Guarantees" can enjoy "Three Guarantees" service. 2).If the use obtains the product in the way of passing-on-hand purchase, and the product is still in the valid period of "Three Guarantees ", with the original formal purchase invoice and "Three Guarantees"...
- Page 29 Ningbo ZhenHai Great Wall Automobile Parts Factory Service hotline：400-8787-011 Fax：0086-574-86303993 Email：fpq@fpqtools.com Wangfudi0102@126.com Address：359 Jinchuan Road, Qingshuipu, Zhenhai District, Ningbo City, Zhejiang Province, China Website：www.fpqtools.com Dealer： Tel：...
- Page 30 Address:...
Need help?
Do you have a question about the 787 and is the answer not in the manual?
Questions and answers