Advertisement
Quick Links
Advertisement
Summary of Contents for Paramount Pools Poolquip Lido
- Page 1 LIDO INGROUND OR INDECK POOLS OVAL POOL INSTRUCTION MANUAL...
- Page 2 LIDO POOL A few important safety hints Enjoy Your Swimming Safely!
- Page 3 LIDO POOL Fence Pool Area (even if it is temporary approved site fencing). Mark out pool location. Prepare site. Set out the final pool dimensions. Assemble frames for pools. Assemble pool ladder. 10. Deepen or dish Pool centre if required. 11.
- Page 4 LIDO POOL Check with your local Council. A building permit may be required or it may be necessary to meet local body regulations. The Fire Department may also require notification. Lido Part No. Details PART1549 The table to the left shows how to select your pool parts. Follow the line on PART1574 which your pool size is shown.
- Page 5 LIDO POOL LINEAL MEASUREMENTS When positioning the pool, ensure that its location meets all Council By-Laws. (FOR TILING AND DECKING) IN PLANNING THE LOCATION OF YOUR POOL, KEEP WATER 1612 – No.1 Wall x 1 = 14.254mtrs SAFETY IN MIND. APPROVED SITE SAFETY FENCING MUST BE 2012 –...
- Page 6 LIDO POOL SET OUT FINAL DIMENSIONS FOR POOL FRAME Once the site is satisfactorily levelled, accurately re-mark the final position of the pools as per the dimensions on the ground plan. The final pool marking should come within the Note: Side braces extend 600mm out from the pool wall. previously levelled area.
- Page 7 LIDO POOL SET OUT FINAL DIMENSIONS FOR POOL FRAME Once the site is satisfactorily levelled, accurately re-mark the final position of the pools as per the dimensions on the ground plan. The final pool marking should come within the Note: Side braces extend 600mm out from the pool wall. previously levelled area.
- Page 8 LIDO POOL SET OUT FINAL DIMENSIONS FOR POOL FRAME Note: Side braces extend 600mm out from the pool wall. APEX OF CURVE PEG No.1 2261mm PEG No.2 RADIUS 1603mm 7087mm 3206mm (To end of base channel) 19mm 591mm 1181mm 1181mm 1181mm 1181mm 1181mm...
- Page 9 LIDO POOL FILTER DRAINAGE DO NOT BACK FILL LOW SIDE OF EXCAVATION Natural surface Excavated leveled surface Straight edge Carpenters level 2. Caution: Do not erect your pool on gravel, asphalt, tar paper or any oil based materials. It is essential that all traces of hardy weeds be completely removed from under the pool as the may puncture the liner.
- Page 10 LIDO POOL ASSEMBLE FRAMES FOR POOLS...
- Page 11 LIDO POOL 7A. PRELIMINARY FRAME EXCAVATION WASHER FITTED BOTH SIDES CHECK VERTICALS WITH CARPENTERS LEVEL CROSS- CHECK LEVELS SAND STAKES TO POSITION BOTTOM RAILS CHECK LEVEL ASSEMBLY OF LOWER RAILS & CONNECTOR 17. Remove frame assembly.
- Page 12 LIDO POOL 19. Excavate the holes for the skid 23. Check whether all uprights are level, 21. Position frames into excavated holes. members 457mm x 457mm x 457mm in line, and level with each other. for concrete. 18. Excavation trenches for the base channel 76mm wide x 76mm deep.
-
Page 13: General View
LIDO POOL CHECK VERTICALS WITH CARPENTERS LEVEL CROSS CHECK LEVEL STAKES TO POSITION BOTTOM RAILS 29. Note: It is Imperative that there is a solid concrete square behind skid member. CHECK LEVEL 30. If the plates are installed on soft fill the weight of water can make the vertical shift out of level. - Page 14 LIDO POOL 7B. SIDEWALL ASSEMBLY 32. and 33. Note: During assembly take special care when handling the sidewall. Careless handling may result in a buckled wall, when erecting. Assembly on very windy days should be avoided. If a colourband wall is being installed, select colour preference and unroll accordingly.
- Page 15 LIDO POOL 8. ASSEMBLE LADDER Stainless steel ladder specially Safety ladder designed for a pool installed in an above ground situation. designed for your inground pool. IMPORTANT! The pool structure and any conductive materials, including but not limited to, stainless steel ladders and aluminum fencing within 1.25mtrs of the pool edge are required to be...
- Page 16 LIDO POOL 10. INSTALL WALLS 11. CUT WALL FOR THE PLUMBING OF THE EYEBALL RETURNS Although the pool wall is supplied with the surface skimmer section pre-punched, the eyeball holes are not cut. This is to allow you to custom fit the eyeball returns (2) in the most suitable position.
- Page 17 LIDO POOL 12. PREPARE COVE AND SPREAD SAND ON BASE 53. Position the liner so that wall-floor 51. Place the pool pad (GROUND COVER) 48. Spread the sand over the entire floor area seam is an equal distance from pool over the entire floor area and hold it in to an even depth of approximately 50mm wall at both ends and sides.
- Page 18 LIDO POOL 17. FIT TOP RAILS/SEATS MAINTENANCE Place one gasket on the inside of the face plate and carefully insert bolts through. starting with the four comers. DO NOT DRAIN THE POOL. Leave the pool filled throughout the year, suitably protected by a winterizing programme.
- Page 19 www. Takapuna 11 Barrys Point Rd, Takapuna Auckland 0622 Email: northshore@paramountpools.co.nz...