1. Manuals
  2. Brands
  3. CS TIMECLOCK Manuals
  4. Time Clocks
  5. 3110
  6. Quick start manual

CS TIMECLOCK 3110 Quick Start Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
CS TIMECLOCK
3110
QUICK START MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 3110 and is the answer not in the manual?

Questions and answers

Related Manuals for CS TIMECLOCK 3110

Summary of Contents for CS TIMECLOCK 3110

  • Page 1 CS TIMECLOCK 3110 QUICK START MANUAL...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS Time Clock Connectors Installation Instructions Hardware Installation Network Setup 2.1. Setting the IP Address 2.2. Setting the NetMask 2.3. Setting the Gateway Address 2.4. Setting the DNS Address 2.5. Enable / Disable DHCP Setting the Time, Date and Time Zone 3.1.

  • Page 3: Time Clock Connectors

    CLOCK INSTALLATION TIME CLOCK CONNECTORS  The connectors are located at the bottom of the clock  The connectors are described below from left to right with the clock display and keypad facing upwards o 1 – Siren Trigger o 2 – 5-12 Volt Power Input Connector o 3 –...
  • Page 4 The TimeClock provides a trigger connector for to a siren interface and is indicated as no 1 under the TimeClock Connector’s section.  The Siren Relay Trigger Connector pin connectors are shown and described below: o Pin 1 and 2 – Normally closed connection o Pin 2 and 3 –...

  • Page 5: Installation Instructions

    INSTALLATION INSTRUCTIONS 1. HARDWARE INSTALLATION  Installation on a upright surface via two key holes at the back of the TimeClock casing  The keyholes are 86mm apart and 23mm from the top of the TimeClock casing as shown in the diagram below: ...

  • Page 6: Network Setup

    2. NETWORK SETUP  Press 900# to view the clock menu  Press 8 to select “Network”  To cancel at any time press * 2.1. SETTING THE IP ADDRESS  Press 1 (“Set IP”). “Swipe Admin Card or Finger” is displayed on screen ...

  • Page 7: Setting The Gateway Address

    2.3. SETTING THE GATEWAY ADDRESS  Enter the “Network” menu as in 2.  Press 3 (“Gateway”). “Swipe Admin Card or Finger” is displayed on screen  Enter 9970#. “Admin Demo User” is displayed for about 2 seconds followed by “Enter Gateway” ...

  • Page 8: Setting The Time, Date And Time Zone

    3. SETTING THE TIME, DATE AND TIME ZONE  Press 900# to view the clock menu  Press 4 to select “Time”  To cancel at any time press * 3.1. SETTING THE TIME FROM THE INTERNET  Press 1 (“ Int Time”). “Swipe Admin Card or Finger” is displayed on screen ...

  • Page 9: Setting The Date Manually

    3.3. SETTING THE DATE MANUALLY  Enter the “Time” menu as in 3.  Press 3 (“Set Date”). “Swipe Admin Card or Finger” is displayed on screen  Enter 9970#. “Admin Demo User” is displayed for about 2 seconds followed by “DATE dd mm yyyy” and the current date below that ...

  • Page 10: Adding An Employee

    4.1. ADDING AN EMPLOYEE  Press 1 (“Add Emp”). “Swipe Supervisor Card or Finger” is displayed on screen  Enter 9970#. “Supervisor Demo User” is displayed for about 2 seconds followed by “Enter New Employee Number”  Enter the employee number followed by # ...

  • Page 11: Appendix A: Time Zone Codes

    APPENDIX A: TIME ZONE CODES  1:  1000: GMT+1 Africa/Johannesburg  2:  2000: GMT+2 Australia/ACT  3:  2001: GMT+3 Australia/North  4:  2002: GMT+4 Australia/NSW  5:  2003: GMT+5 Australia/Queensland  6:  2004: GMT+6 Australia/South ...

Table of Contents