ABNICS FT23D User Manual
  1. Manuals
  2. Brands
  3. ABNICS Manuals
  4. Touch terminals
  5. FT23D
  6. User manual

ABNICS FT23D User Manual

Face recognition terminal
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ABNICS FT23D
Face Recognition Terminal
User Manual
Issue
V1.1
Date
2020-12-18

Advertisement

Table of Contents
loading

Summary of Contents for ABNICS FT23D

  • Page 1 ABNICS FT23D Face Recognition Terminal User Manual Issue V1.1 Date 2020-12-18...

  • Page 3: Precautions

    ABNICS FT23D - Face Recognition Terminal User Manual Precautions Precautions Fully understand this document before using this device, and strictly observe rules in this document when using this device. If you install this device in public places, provide the tip "You have entered the area of electronic surveillance"...
  • Page 4 ABNICS FT23D - Face Recognition Terminal User Manual If this device is installed in places with unsteady voltage, ground this device to discharge high energy such as electrical surges in order to prevent the power supply from burning out. When this device is in use, ensure that no water or any liquid flows into the device. If water or liquid unexpectedly flows into the device, immediately power off the device and disconnect all cables (such as power cables and network cables) from this device.
  • Page 5 ABNICS FT23D - Face Recognition Terminal User Manual Special Announcement All complete products sold by the manufacturer are delivered along with nameplates, operation instructions, and accessories after strict inspection. The manufacturer shall not be held responsible for counterfeit products. This manual may contain misprints, technology information that is not accurate enough, or product function and operation description that is slightly inconsistent with the actual product.

  • Page 7: Table Of Contents

    ABNICS FT23D - Face Recognition Terminal User Manual Contents Precautions ........................i Contents ........................1 1 Hardware Description ..................... 3 1.1 Product Features ......................3 1.2 Unlock Insturctions ......................4 1.3 Appearance Instructions and Cable description .............. 5 1.4 Requirement of Use ......................8 1.5 Dimensions ........................
  • Page 8 ABNICS FT23D - Face Recognition Terminal User Manual 3.6.2 Alarm Linkage Email ..................33 3.6.3 Alarm Input ...................... 34 3.7 Network Service ......................35 3.7.1 Upload Service ....................35 3.7.2 SMTP ....................... 35 3.8 UI & Sound Settings ....................36 3.9 Temperature Parameters ....................

  • Page 9: Hardware Description

    ABNICS FT23D - Face Recognition Terminal User Manual Hardware Description 1.1 Product Features Based on self-developed AI chip, with the support of powerful computing power and face recognition algorithms, temperature measurement face recognition terminals are designed to detect skin-surface temperatures, and can thus be used for rapid and preliminary fever screening in office buildings;...

  • Page 10: Unlock Insturctions

    ABNICS FT23D - Face Recognition Terminal User Manual 1.2 Unlock Insturctions Face recognition terminal can control the lock of door through the multi cable connect to system, in the retention of existing access control system function of the colleague, the access control intelligent operation upgrade.

  • Page 11: Appearance Instructions And Cable Description

    ABNICS FT23D - Face Recognition Terminal User Manual 1.3 Appearance Instructions and Cable description Figure 1-1 Appearance Instructions Issue V1.1 (2020-12-18)
  • Page 12 ABNICS FT23D - Face Recognition Terminal User Manual Figure 1-2 Multi cable Different device may have different multi-head cable, please refer to actual products. Table 1-1 Cable description Description Description Remarks 1RJ45 Network port Connect to Ethernet Not support POE...
  • Page 13 ABNICS FT23D - Face Recognition Terminal User Manual suspended; Connect to Access control’s COM-NO is short-circuited when the door lock is triggered; NC is suspended; 4USB USB port Connect to USB ID reader. 5ALARM- Connect to alarm device line 1...

  • Page 14: Requirement Of Use

    ABNICS FT23D - Face Recognition Terminal User Manual Figure 1-3 Multi cable connection diagram 1.4 Requirement of Use To ensure the measurement accuracy, please install the devices indoors, with 20~35℃(68-95℉) ambient temperature. No other obvious heat source around No cover on forehead It is recommended to start measure temperature after 30 minutes being powered on.
  • Page 15 ABNICS FT23D - Face Recognition Terminal User Manual Figure 1-4 Dimensions (unit: mm) Issue V1.1 (2020-12-18)

  • Page 16: Installation And Precaution

    ABNICS FT23D - Face Recognition Terminal User Manual 1.6 Installation and Precaution Figure 1-5 Accessories description Position of opening hole： The diameter of the steel plate opening is 34 mm, the specific position depends on the situation. When the all-in-one is installed in the factory configuration, the elevation angle is about 5°.
  • Page 17 ABNICS FT23D - Face Recognition Terminal User Manual 65 cm 140~195 cm Distance between person and device Recognizable height range 65 cm 130~185 cm 75 cm 130~190 cm 85 cm 130~195 cm Place at an elevation without adding a column...
  • Page 18 ABNICS FT23D - Face Recognition Terminal User Manual Figure 1-7 Fix steel plate Issue V1.1 (2020-12-18)
  • Page 19 ABNICS FT23D - Face Recognition Terminal User Manual Instruction of wall mounting ： When mounting on the wall, user can choose to drill hole on wall, or no drill hole, the accessory is optional following with the different installment. 4-φ5 4-φ3.5...
  • Page 20 ABNICS FT23D - Face Recognition Terminal User Manual Figure 1-8 Wall mounting (drill the passing cables hole) Groove Insert completed Wall bracket’s tray Lock scr ew Drill holes (56 X 36 mm) on the wall as the dimensions of the wall bracket, insert the rubber plug into the hole, and reserve a cable hole on the wall;...
  • Page 21 ABNICS FT23D - Face Recognition Terminal User Manual After the device falls to the final position, tighten the middle screw at the bottom of the device. Figure 1-9 Wall mounting （no the passing cables hole） Groo ve In se rt co mple te d Wa ll bra cket’s tray...

  • Page 22: Packaging And Instrctions

    ABNICS FT23D - Face Recognition Terminal User Manual Drill holes (75 X 60 mm) on the wall as the dimensions of the wall bracket, insert the rubber plug into the hole; Fix the wall mount bracket to the wall plug with 4 self-tapping screws, and pass the equipment wire through the wall mount bracket up or down depending on the need;...

  • Page 23: Quick Configuration

    ABNICS FT23D - Face Recognition Terminal User Manual Quick Configuration 2.1 System Login and Logout Enter the device IP address in the address bar of the Firefox browser or Google Chrome (device default IP:192.168.0.120, the IP is showing on device panel.), press Enter to open the login page, as shown in Figure 2-1.
  • Page 24 ABNICS FT23D - Face Recognition Terminal User Manual Figure 2-2 Activation page Figure 2-3 Security configuration questions You can exit to the login page by clicking the Exit button in the top right corner of the page. If you have forgotten your password, you can answer the security configuration questions to verify identity, set the new password, as shown in Figure 2-4.

  • Page 25: Modify The Password

    ABNICS FT23D - Face Recognition Terminal User Manual Figure 2-4 Forgetting password ----End 2.2 Modify the Password At “Configuration < System < User Management” interface to modify the password, as shown in Figure 2-5. Issue V1.1 (2020-12-18)
  • Page 26 ABNICS FT23D - Face Recognition Terminal User Manual Figure 2-5 User Management Choose the user name from the user list, click “Modify” to change a new password, as shown in Figure 2-6. Figure 2-6 Modify password ----End Issue V1.1 (2020-12-18)

  • Page 27: Preview Interface

    ABNICS FT23D - Face Recognition Terminal User Manual 2.3 Preview Interface 2.3.1 Download VLC Enter the web interface, as shown in Figure 2-7. User need to download the VLC player at first login. Figure 2-7 Download VLC Following the reminder to download the VLC, after installing the VLC, browse the IP again, as shown in Figure 2-8.

  • Page 28: Live Video Interface

    ABNICS FT23D - Face Recognition Terminal User Manual 2.3.2 Live Video Interface The page setting items of the notify sound and interface are as shown in Figure 2-9. Figure 2-9 Preview interface 1. The live video interface. 2. Configuration, set the system, communication, video, image, algorithm, face database.

  • Page 29: Configuration Setting

    ABNICS FT23D - Face Recognition Terminal User Manual Configuration Setting 3.1 Basic Information At basic information interface, user can set the device name, device ID, view the device model, device serial number, hardware version, web version, thermal serial, thermal SDK version, as shown in Figure 3-1.

  • Page 30: Logo Settings

    ABNICS FT23D - Face Recognition Terminal User Manual Figure 3-2 Time configuration page There are two modes to set time, NTP timing and manual timing. 3.2.2 Logo Settings At “ Configuration > System > Logo Setting” interface, User can custom the logo of company, as shown in Figure 3-3.

  • Page 31: User Management

    ABNICS FT23D - Face Recognition Terminal User Manual 3.2.3 User Management At “ Configuration > System > User Management” interface, user can modify the security question and password, as show in Figure 3-4. Figure 3-4 User management interface Click “Security question” the pop-up window shows as following, input the password to enter security configuration questions, as shown in Figure 3-5.
  • Page 32 ABNICS FT23D - Face Recognition Terminal User Manual Figure 3-5 Security qusetion Choose the questions, and input the answers, if the password was forgot, you can use the security questions to verify identity and set the new password. Choose the admin user, click “Modify” to modify password, as shown in Figure 3-6.

  • Page 33: System Parameters

    ABNICS FT23D - Face Recognition Terminal User Manual Figure 3-6 User modify ----End 3.2.4 System Parameters At “ Configuration > System > System Parameters” interface, set the parameters of system. Normal Setting: Attribute Settings, Recognize Settings, Capture Timing Delete Trigger EMMC Snapshot, ID Reader, as shown in Figure 3-7.
  • Page 34 ABNICS FT23D - Face Recognition Terminal User Manual Figure 3-7 System parameters interface Table 3-1 System parameters Parameter Description Configuration Method Attribute Enable the attribute, you can choose whether to [Setting method] Settings detect body temperature or do mask detection,...

  • Page 35: Communication Settings

    ABNICS FT23D - Face Recognition Terminal User Manual ----End 3.3 Communication Settings At communication interface, user can set TCP/IP, Device Port settings. 3.3.1 TCP/IP At “ Configuration > Communication > TCP/IP” interface, user can set the TCP/IP parameters, as shown in Figure 3-8.

  • Page 36: Video Settings

    ABNICS FT23D - Face Recognition Terminal User Manual Figure 3-9 Device Port Configuration interface Input the http port(default is 80) and https port(default is 443). Click “Save” to save the settings. You will need to login the web using the new port after changing the port.

  • Page 37: Image Settings

    ABNICS FT23D - Face Recognition Terminal User Manual 3.5 Image Settings At “ Configuration > Image” interface, user can set display settings and exposure Area ROI, as shown in Figure 3-11. Figure 3-11 Image settings interface 3.5.1 Display Settings At display settings page, user can set image adjustment, digital wide dynamic, HDR, exposure settings, face AE settings and other parameters.
  • Page 38 ABNICS FT23D - Face Recognition Terminal User Manual Digital Wide Dynamic： When low-brightness areas and high-brightness areas appears in the same picture at the same time, it may cause overexposure or loss of details in the dark. Turning on wide dynamic can enhance the dark part and suppress the bright part to get better performance.

  • Page 39: Alarm

    ABNICS FT23D - Face Recognition Terminal User Manual Figure 3-15 Other page ---End 3.6 Alarm At alarm interface, user can set the Alarm Linkage IO Output, Alarm Linkage Email, and Alarm Input. 3.6.1 Alarm Linkage IO Output At “ Configuration > Alarm > Alarm Linkage IO Output” interface, user can tick the abnormal temperature link, abnormal mask link, no match alarm link, set alarm duration, as shown in Figure 3-16.

  • Page 40: Alarm Input

    ABNICS FT23D - Face Recognition Terminal User Manual Figure 3-17 Alarm linkage Email ---End 3.6.3 Alarm Input At “ Configuration > Alarm > Alarm Input” interface, user can enable the alarm input. Choose the alarm index(it depends on which alarm input port is used.), choose the trigger mode(it depends on the feature of alarm input device.), as shown in Figure 3-18.

  • Page 41: Network Service

    ABNICS FT23D - Face Recognition Terminal User Manual 3.7 Network Service 3.7.1 Upload Service At “ Configuration >Network Service > Upload Service” interface, set the parameters of HTTP Upload Server Settings, MQTT Upload Server Settings, and Back Ground Settings as shown in Figure 3-19.

  • Page 42: Ui & Sound Settings

    ABNICS FT23D - Face Recognition Terminal User Manual Figure 3-20 SMTP Table 3-3 SMTP Parameter Description SMTP Server Address The server address of Email. SMTP Server Port The server port of Email Username The username of Email Password The password of Email...
  • Page 43 ABNICS FT23D - Face Recognition Terminal User Manual Figure 3-21 UI & Sound interface Issue V1.1 (2020-12-18)
  • Page 44 ABNICS FT23D - Face Recognition Terminal User Manual Table 3-4 UI & Sound settings Parameter Description Configuration Method Panel UI Settings Tick the show IP, show track box, show [Setting method] number of registrations, show measure area, Tick, or choose...
  • Page 45 ABNICS FT23D - Face Recognition Terminal User Manual Enable the pass scene to set the picture setting Pass scene [Setting method] and sound setting. When someone pass it will Tick, and choose show picture on UI panel, or play the sound the file reminder, as shown in Figure 3-25.
  • Page 46 ABNICS FT23D - Face Recognition Terminal User Manual Figure 3-23 Mask detection Figure 3-24 Over temperature detection Figure 3-25 Pass scene Figure 3-26 Liveliness detection Issue V1.1 (2020-12-18)

  • Page 47: Temperature Parameters

    ABNICS FT23D - Face Recognition Terminal User Manual Figure 3-27 No match detection ----End 3.9 Temperature Parameters At “ Configuration > Temperature Parameters” interface, set the parameters of temperature, as shown in Figure 3-28. Figure 3-28 Temperature parameters interface Table 3-5 Temperature parameters...

  • Page 48: Access Condition

    ABNICS FT23D - Face Recognition Terminal User Manual Temperature Set the unit of temperature, min temperature, [Setting method] Parameters max temperature, correction coefficient, Input the value, environment temperature offset, emulate or choose from temperature mode(normal-1 and normal-2) drop-down list. ----End 3.10 Access Condition...
  • Page 49 ABNICS FT23D - Face Recognition Terminal User Manual Table 3-6 Access condition Parameter Description Configuration Method Unlock Condition Enable body temperature access control mode, [Setting method] (Confirm Enable mask access control mode, and guest access Tick Attribute) control mode. Body temperature mode: As long as the...

  • Page 50: System Maintenance

    ABNICS FT23D - Face Recognition Terminal User Manual Figure 3-30 Wiegand input interface Figure 3-31 Wiegand output interface ----End 3.11 System Maintenance 3.11.1 Upgrade and Maintenance At “ Configuration > System Maintenance > Upgrade and Maintenance interface, user can upgrade and maintenance, thermometer upgrade, as shown in Figure 3-32 .
  • Page 51 ABNICS FT23D - Face Recognition Terminal User Manual Figure 3-32 System maintenance interface Language: Change the language of web, as shown in figure Reboot: Reboot the device, click “Reboot”, on the pop-up window , click “OK” , wait few seconds, the device will restart.

  • Page 52: Thermometer Upgrade

    ABNICS FT23D - Face Recognition Terminal User Manual Upgrade Browse the local folder where the upgrade software locates, click “Upgrade” to upgrade the device. 3.11.2 Thermometer Upgrade At “ Configuration > System > thermometer upgrade interface, user can upgrade the software of thermometer module, as shown in Figure 3-33 .

  • Page 53: Face Database

    ABNICS FT23D - Face Recognition Terminal User Manual Face Database At Face database interface, user can add face information to the local database, and support up to 30,000 face information. User can delete, import, export, search the database. Click “+” to add new face database, as shown in Figure 4-1.
  • Page 54 ABNICS FT23D - Face Recognition Terminal User Manual Figure 4-2 Add person Add person should input name, work ID, add picture. Other parameter is optional, the password is used for UI panel to unlock by password. Tick the persons want to be delete, click “Delete” to delete.
  • Page 55 ABNICS FT23D - Face Recognition Terminal User Manual Figure 4-4 Search person to modify the information, as shown in Figure 4-5. Click “OK” to save the changes. Click Figure 4-5 Modify personal information Click to delete the person information, the pop-up window showing, click “OK”...

  • Page 56: Capture History

    ABNICS FT23D - Face Recognition Terminal User Manual Capture History Set the start time and end time to search capture image, it will show capture time ,FIG sheet, mask, temperature, and the scanning result as shown in Figure 5-1. Figure 5-1 Capture History interface The FIG sheets are saved in camera, it can save up to 30000 image records, the images can be overwritten.
  • Page 57 ABNICS FT23D - Face Recognition Terminal User Manual Figure 5-2 Set detail time User can set the detail time to search. ----End 101-300-0585-02 Issue V1.1 (2020-12-18)

Table of Contents