Table of Contents
Advertisement
Quick Links
If you have any questions, please email our technical team at
support@autohomation.com
Call for immediate assistance from our technical support team
1800-XXX-XXXX
INSTALLATION MANUAL -
PRIME LOCK
REV 01
For easy-to-follow installation instructions, please visit our
Visit us at
www.autohomation.com
website for installation video at
www.autohomation.com
Advertisement
Table of Contents
Related Manuals for AUTO HOMATION PRIME LOCK
Summary of Contents for AUTO HOMATION PRIME LOCK
- Page 1 If you have any questions, please email our technical team at support@autohomation.com Call for immediate assistance from our technical support team 1800-XXX-XXXX INSTALLATION MANUAL - PRIME LOCK REV 01 For easy-to-follow installation instructions, please visit our Visit us at www.autohomation.com website for installation video at www.autohomation.com...
-
Page 2: Instructions
Such warranty will cover repair or replacement of any defective parts at AutoHomation premises and subjected to the following conditions, provided that • Prime Lock is fitted to a patio type sliding door strictly following the supplied instructions • Sliding door is free sliding within the limits of the trial load sliding door puller supplied •... -
Page 3: Table Of Contents
WARRANTY APPLICABILITY CONTENTS This warranty shall be null and void and to no affect if: Instructions …………………………………..............• Prime Lock is abused or in any way used outside the limits of the Introduction…………………………………..............specification anddesign, Warranty..…………………………………........…......• The electric wiring has been interfered with and is not wired in accordance with the original factory settings. -
Page 4: Prime Lock Package Contents
PRIME LOCK PACKAGE CONTENTS PARTS INTRODUCTION Rack Controller Cover Controller Part Details Enclosure Adapter Bracket Assorted Screws Remote Wireless Push Button Tooth cap nut Automatic door Microwave sensor Gear rack Power plug Wireless push button... -
Page 5: Tools Required
TOOLS REQUIRED PRIME LOCK - ABOUT Prime Lock, automatic slider for patio door, is inbuilt with an effective controller that 1. No. 2 flat head screwdriver enables the smooth movement of the patio door with a rack and pinion mechanism. -
Page 6: Application Of Mounting Bracket
INSTALLATION STEPS STEP 3: RACK SELECTION STEP 1: SELECTION OF SYSTEM MOUNTING LOCATION Place the cap on Top Mounting 1 Top Mounting 2 to the rack of close direction Connect the two racks together when the door/window width over 0.5 feet. -
Page 7: Controller Installation Method
RACK FITTING STEP 4: CONTROLLER INSTALLATION METHOD 1 Place controller on top Make pencil marks of door frame when for width of the door is fully closed. door/window on Position it from center both edges as of the whole door at shown. -
Page 8: Controller Installation Method
Position it Two wireless push buttons are supplied with Prime Lock, one for each side of the door. from center of the Measure 3 feet (1m) up from the floor and mark on the door frame, inside and out. -
Page 9: Adjusting The Controls And Programming Sensors
Once all the iii. The light will go out when the Prime Lock has learnt each sensor. testing is done, place the top To clear all ‘learnt’ devices press and hold the learn button for 5 seconds. -
Page 10: Dip Function Introduction And Setting
Congratulations, you should now have a fully functioning Active any terminal of A and B at same time, will work active to open or active to Prime Lock automatic door!! close. Attention: Must be one terminal from A and B active at same time. -
Page 11: Operating Modes
OPERATING MODES learn cycle is successful. The Prime Lock has now memorized the width of the door Once the door is operating correctly the desired mode can be selected:. There are five opening, the weight and friction of your door while sliding. And now knows the modes available: individual power to operate your door smoothly and reliable. -
Page 12: Setting Of Wireless Push Button
Door will be closed slowly, if it is 3. GND 16. GND open. Once the power is on, the Prime Lock resumes normal working (the working 4. UPS + 17. Outside Sensor mode is same selection before power off). -
Page 13: Troubleshooting
SOLUTION: Double check that there is a slight gap between the rack teeth and pinion SOLUTION: Remove the external cover (if already fitted). Turn the Prime Lock off at the cog along the entire length of the rack. Adjust as required. Note: it may be easier to controller switch.
Need help?
Do you have a question about the PRIME LOCK and is the answer not in the manual?
Questions and answers